StickS3 Compact and High Performance Programmable Controller
“
StickS3 Product Information
Mga pagtutukoy:
- SoC: ESP32S3
- PSRAM: Included
- Flash: Hindi tinukoy
- Input Power: Hindi tinukoy
- Audio Codec: Integrated
- MEMS Microphone: Included
- Tagapagsalita: Kasama
- Operating Temperature: Hindi tinukoy
Mga Tagubilin sa Paggamit ng Produkto:
Mabilis na Pagsisimula:
Paghahanda:
- Bisitahin ang opisyal na Arduino website at i-install ang Arduino IDE
mula sa dito. - Idagdag ang sumusunod na Board Manager URL sa File > Mga Kagustuhan
> Karagdagang Boards Manager URLs:
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json - Buksan ang Boards Manager, hanapin ang ESP32, at i-click
i-install. - Pagkatapos ng pag-install, piliin ang board ESP32S3 Dev Module.
- I-configure ang mga sumusunod na pagpipilian:
- USB CDC On Boot: Enabled
- PSRAM: PSRAMOPI PSRAM
- USB Mode: Hardware CDC and JTAG
Wi-Fi Scan:
Piliin ang exampang programa Halamples > WiFi > WiFiScan,
piliin ang port na naaayon sa iyong device, at i-click ang compile
at pindutan ng pag-upload sa kaliwang sulok sa itaas. Pagkatapos mag-upload ay
kumpleto, buksan ang Serial Monitor sa view Wi-Fi scan
impormasyon.
BLE Scan:
Piliin ang exampang programa Halamples > BLE > I-scan, piliin
ang port na naaayon sa iyong device, at i-click ang compile at
button sa pag-upload sa kaliwang sulok sa itaas. Matapos makumpleto ang pag-upload,
buksan ang Serial Monitor sa view Impormasyon sa pag-scan ng BLE.
Babala sa FCC:
Sumusunod ang produktong ito sa Bahagi 15 ng Mga Panuntunan ng FCC. Operasyon
ay napapailalim sa sumusunod na dalawang kundisyon: (1) Maaaring hindi ang device na ito
maging sanhi ng mapanganib na pagkagambala, at (2) dapat tanggapin ng aparatong ito ang anuman
interference na natanggap, kabilang ang interference na maaaring magdulot
hindi gustong operasyon.
FAQ:
Q: Ano ang dapat kong gawin kung makatagpo ako ng mga isyu sa panahon ng
proseso ng pag-install?
A: Kung makatagpo ka ng anumang mga isyu sa panahon ng pag-install o pag-setup,
refer to the troubleshooting section in the official Arduino
documentation or contact our customer support for assistance.
“`
StickS3
1. Paglalarawan
StickS3 is a compact and high-performance programmable controller specifically designed for remote control and IoT applications. At its core, it features the ESP32-S3-PICO-1-N8R8 main control chip, supports 2.4 GHz Wi-Fi wireless communication, and comes with 8MB Flash and 8MB PSRAM, meeting the needs of diverse application development while delivering outstanding performance and expandability. For human-machine interaction, it is equipped with a 1.14″ LCD display, a 6-axis IMU sensor, and programmable buttons. The audio system employs the ES8311 mono codec, combined with a high-sensitivity MEMS microphone and an AW8737 power amplifier, enabling clear sound pickup and high-fidelity audio output for voice recognition and interactive experiences. Additionally, it integrates IR transmitter and receiver tubes, along with a 250mAh lithium battery, making it suitable for applications such as smart home control, AI voice assistants, and IoT project development.
2. Mga pagtutukoy
Specification SoC
PSRAM Flash Input Power Audio CodeC MEMS Microphone Speaker Operating Temperature
Parameters ESP32-S3-PICO-1-N8R8 @ Dual-core Xtensa LX7 processor, up to 240MHz main frequency 8MB 8MB USB: DC 5V ES8311: 24-bit resolution, using I2S protocol MSM381A3729H9BPC, Signal-to-Noise Ratio (SNR): 65 dB AW8737 power amplifier,2011 cavity speaker: 1W@8 0 ~ 40°C
3. Mabilis na Pagsisimula
3.1 Paghahanda
1. Bisitahin ang opisyal na Arduino website at i-install ang Arduino IDE https://www.arduino.cc/en/Main/Software 2. Idagdag ang sumusunod na Board Manager URL sa File Mga Kagustuhan sa Karagdagang Boards Manager URLs: https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Buksan ang Boards Manager, hanapin ang “ESP32”, at i-click ang i-install.
4. After installation, select the board “ESP32S3 Dev Module” 5. Configure the following options. USB CDC On Boot: “Enabled”, PSRAM”OPI PSRAM”,
USB Mode: “Hardware CDC and JTAG”
3.2 Pag-scan ng Wi-Fi
Piliin ang exampang programang “Halamples" "WiFi" "WiFiScan", piliin ang port na naaayon sa iyong device, at i-click ang compile at upload button sa kaliwang sulok sa itaas. Pagkatapos makumpleto ang pag-upload, buksan ang Serial Monitor upang view Impormasyon sa pag-scan ng Wi-Fi.
3.3 BLE Scan
Piliin ang exampang programang “Halamples” “BLE” “Scan”, piliin ang port na naaayon sa iyong device, at i-click ang compile at upload button sa kaliwang sulok sa itaas. Pagkatapos makumpleto ang pag-upload, buksan ang Serial Monitor upang view Impormasyon sa pag-scan ng BLE.
4. Babala ng FCC
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Mga Dokumento / Mga Mapagkukunan
 |
M5STACK StickS3 Compact and High Performance Programmable Controller [pdf] User Manual 2AN3WM5STICKS3, 2AN3WM5STICKS3, M5STICKS3, StickS3 Compact and High Performance Programmable Controller, StickS3, Compact and High Performance Programmable Controller, High Performance Programmable Controller, Programmable Controller |