TiNLY Sp/lit Bluetooth CD Player
Products Overview
Screen Display and Key Description
CD player&Speaker all in one
Button Description
Complete Model
Bluetooth pair
Press the mode button to switch to the BT-IN mode.
Mobile phone connection
Bluetooth signal “SPLIT” CD PLAY Press MODE button to switch to CD PLAY mode. It will be playing the cd disk.
Bluetooth output
Press the MODE button to switch to BT-OUT mode. Connects to external Bluetooth devices.
CD Player
Button Description
CD Player Button Description
Wireless connection to external Bluetooth speaker devices
Note: If the device is independent, connect the power supply
- Step1 Press the MODE button to enter BT-OUT mode
- Step 2 Turn on the external speaker, Adjust to Bluetooth pairing status
- Step 3 Bluetooth connection successful
Wireless connection to SPLIT
- Step 1 Press the MODE button to switch to BT-OUT mode
- Step 2 Turn on the power, Verify that the speaker is in Bluetooth pairing mode (blue light flash)
- Step 3 Bluetooth connection successful
Bluetooth speaker
Description
Bluetooth speaker Independent Use
Bluetooth input
- Step 1 Automatically enter Bluetooth search mode after power on.
The indicator light is on and the blue light is flashing. - Step 2 Mobile phone connection Bluetooth signal “split”.
Main Specifications
- Supported formats CD-DA/MP3 (CDR-RW)
- CD-R/RW MP3 (32-320k bps)
- Bluetooth output protocol SBC and AAC
- Output (main unit) 3.5mm stereo audio output jack/Bluetooth 5.3
- Power 5W, standby power 0.5W
- Power Supply DC5V/2ATYPE-C interface/ built-in battery 2000mAh
- Maximum external dimensions 230mm*138mm*35mm
- Mass 595g
- Accessories 595g TYPE-C power cable *1, CD player *1
*This product does not support the use of dry batteries
Safety Precautions
- 0nly CD discs containing the logo shown at the right can be played on this set.
- Do not stick a label etc. on a disc.
- Do not heat discs.
- Do not use this apparatus near water.
- Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged,liquid has been spilled or objects have fallen into the apparatus has been exposed to ain or moisture, does not operate normally, or has been endropped. - Do not place heavy objects on the CD player.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not install near strong magnetic fields or electrical sources.
- Spraying flammable insecticides near the unit.
- Must recycle the processing battery correctly.
- Do not place the battery in a place where it isexposed to strong light/where the fire source is overheated.
Issues & Solutions
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction
Documents / Resources
 | Sp/lit Bluetooth CD Player |
References
- User Manualmanual.tools
The speaker still has no sound, and the blue light is flashing in pairing mode, but it isn’t working. I’ve already switched to BT-OUT mode, but it won’t pair with the CD player. What should I do? I need help, because The CD player works with wired headphones.
How do I troubleshoot Bluetooth pairing issues between the TiNLY Sp/lit CD player and an external speaker when BT-OUT mode is active but no sound is produced?
Based on the TiNLY Sp/lit manual, please follow these troubleshooting steps to resolve the pairing and sound issues:
If the blue light continues to flash without turning solid, try resetting both devices by turning them off and back on, then initiating the pairing process again starting with the speaker first.
Read the full Q&A page