Tianjin 2.4GHz Touch Remote RGB Controller 

Specifications

• Model: [Insert Model Number]
• Compliance: FCC
• RF Exposure: General RF exposure requirement met

Product Usage Instructions

RF Exposure Information

The device has been evaluated to meet general RF exposure requirements. It can be used in 0mm exposure conditions while complying with exposure requirements . Only when used under the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

CAUTION

1. Do not expose the components of this product t direct moisture.
2. Do not expose the components of this product to excessively high temperatures.
3. Please keep out of reach of children.
4. Please consult your owner’s manual and/or local dealer if issues arise.
5. Do NOT mix alkaline, standard, and rechargeable Batteries.
6. Do NOT mix old and new Batteries.
7. Exhausted Batteries should be removed immediately from the Remote. 8  . The supply terminals are not to be short-circuited.

TECHNICAL PARAMETERS

Remote		Receiver
Control Freq.	2.4G Hz RF	Input	Dc12v~24v
Power Supply	2*AAA battery	Output	3 Channel)
		Output current	6A(each channel)
Standby Power Consumption	lOuA	Output Power	Max 216W/432W(12V/24V)
Size:	L110xW53xH20mm	Connecting mode	Common anode
Remote Distance	>20m	Output gary level	256
Standby time	6 months	Size:	L86xW45xH23mm

REMOTE INTERFACE

CONTROLLER INTERFACE

CONNECTION INTERFACE

Materials:

1. One Power Adapter, or a DC12-24V Source. To give DC Voltage to the Receiver 2, Two AAA Batteries, to power the Remote
2. One LED RG B Strip

OPERATING PROCESS

1.  Refto er to Ronnecting Setup, and make sure the controller is connected correctly. And connect the LED to the Receiver correctly.
2. Load the Batteries to the Remote.
3. Power on the Receiver. And the LED will illuminate. If the LED does NOT illuminate, pis check the wire connection.  Reset the wire and restore the power to the Controller.
4. If necessary, pis pair the Receiver to the Remote. Refer to the below process … After pairing successfully, the Remote can only control the Receiver.
5. Now using the Remote, you can manage the color of the LED, and select the Operating Mode. 6, The Operating Mode is listed as the Program List below.

PROGRAM LIST

(The mode is just for reference, The actual modes are by the product criterion that has been received.)

PS: R&red G&green B&blue W&white

Paring The Receiver to the remote 

For some particular applications if you want one Remote only control one Receiver, then the Receiver is required to be paired to the Remote. Here below is the guide.

Before any action setup the controller correctly:

1. Load the Batteries into the Remote.
2. Connect the LED to the Receiver.
3. Connect the Receiver to the Power Supply

Pairing the Receiver to the Remote.

1. Switch off the main power supply to the Receiver.
2. Restore power, and within 6 seconds, sync depresses the two buttons for more than 2second., as picture.
3. If the LED flashes, that means the successful pairing process. 4, If the LEDs don’t flash, repeat the step to step 2.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedbyh the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirements device can be used in 0mm exposure conditions,an d   omp compliance exposure requirements. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

Frequently Asked Questions

Q: Can the device be used in any other exposure conditions?
A: The device is recommended to be used in 0mm exposure conditions to ensure compliance with RF exposure requirements.

Q: What is the significance of meeting FCC RF Exposure requirements?
A: Meeting FCC RF Exposure requirements ensures that the device operates within safe exposure limits for users

Documents / Resources

Tianjin 2.4GHz Touch Remote RGB Controller [pdf] User Manual 2BNC9-ET641RC, 2BNC9ET641RC, et641rc, 2.4GHz Touch Remote RGB Controller, Touch Remote RGB Controller, Remote RGB Controller, RGB Controller, Controller

References

• User Manual