Aideepen ESP8266 V3 ESP-12E NodeMCU Development Board User Manual

1. บทนำ

The Aideepen ESP8266 V3 ESP-12E NodeMCU Development Board is a versatile Wi-Fi module designed for Internet of Things (IoT) applications. It integrates the ESP-12E module, offering full I/O port access and 802.11 wireless connectivity. This board features a built-in Micro-USB port, flash memory, and a reset switch, simplifying the programming process. It supports STA, AP, and STA+AP working modes, providing flexibility for various network configurations. Its low deep sleep current consumption makes it suitable for power-sensitive projects.

2. คุณสมบัติ

• Integrated ESP-12E Module: Provides 802.11 b/g/n Wi-Fi connectivity.
• Full I/O Port Support: Access to all available input/output pins for project flexibility.
• พอร์ตไมโครยูเอสบี: For power supply and data communication, facilitating easy programming.
• Flash and Reset Switches: Convenient buttons for programming and system reset.
• โหมดการทำงานหลายแบบ: Supports Station (STA), Access Point (AP), and combined STA+AP modes.
• การใช้พลังงานต่ำ: Deep sleep current is approximately 10µA, and off current is less than 5µA.
• Event-Driven API: Accelerates IoT application development.

3. คู่มือการติดตั้ง

Follow these steps to set up your Aideepen ESP8266 V3 ESP-12E NodeMCU Development Board:

1. Install CH340G Driver: The board uses a CH340G USB-to-Serial chip. Before connecting the board to your computer, install the appropriate CH340G driver for your operating system. Drivers are typically available online from CH340G manufacturers or NodeMCU community resources.
2. เชื่อมต่อบอร์ด: Use a Micro-USB cable to connect the NodeMCU board to your computer. Ensure the connection is secure.
3. Configure IDE: Open your preferred Integrated Development Environment (IDE), such as the Arduino IDE or VS Code with PlatformIO. Configure the IDE to recognize the ESP8266 board and select the correct COM port.
4. กำหนดอัตราการรับส่งข้อมูล: For communication and flashing firmware, set the baud rate to 9600bps or higher, as required by your specific application or firmware.
5. รหัสอัปโหลด: You can now upload your code or firmware to the board. The built-in flash and reset switches simplify this process, often requiring no manual button presses during upload.

4. คู่มือการใช้งาน

The NodeMCU ESP8266 V3 ESP-12E board is designed for flexible operation in various network environments.

4.1 โหมดเครือข่าย

• Station (STA) Mode: In this mode, the ESP8266 connects to an existing Wi-Fi network (e.g., your home router) as a client device. It can then access the internet or communicate with other devices on that network.
• โหมดจุดเข้าใช้งาน (AP): In AP mode, the ESP8266 creates its own Wi-Fi network, allowing other devices (like smartphones or computers) to connect directly to it. This is useful for direct device-to-device communication without an intermediary router.
• STA+AP Mode: This mode combines both Station and Access Point functionalities, allowing the ESP8266 to connect to an existing network while simultaneously hosting its own network.

4.2. การเขียนโปรแกรมและการพัฒนา

The board is compatible with various programming environments, including the Arduino IDE (with ESP8266 board support package) and NodeMCU Lua firmware. Developers can write code in C++ (Arduino) or Lua to control the board's functionalities, interact with sensors, and manage network communications.

5. แผนภาพพินเอาท์

Understanding the pinout is essential for connecting peripherals and utilizing the full capabilities of the NodeMCU board. The board features 30 pins arranged in two rows.

Key pin functions include:

• GPIO (General Purpose Input/Output) Pins: D0-D8, SDD0-SDD3, SDCMD, SDCLK, MOSI, MISO, SCLK, CS. These pins can be configured as inputs or outputs for connecting sensors, actuators, and other components.
• พินไฟฟ้า: 3V3 (3.3V output), Vin (5V input via USB or external supply), GND (Ground).
• Communication Pins: RX (Receive), TX (Transmit) for serial communication.
• Special Function Pins: A0 (Analog Input), RST (Reset), EN (Enable), FLASH (Flash button), WAKE (Wake-up pin).

Important Note: The I/O pins operate at 3.3V. Applying 5V directly to these pins without a level shifter can damage the board.

6. ข้อมูลจำเพาะ

7 การแก้ไขปัญหา

• คอมพิวเตอร์ตรวจไม่พบแผงวงจร:
  • Ensure the CH340G driver is correctly installed.
  • Try a different Micro-USB cable; some cables are for charging only.
  • ลองเสียบพอร์ต USB อื่นบนคอมพิวเตอร์ของคุณดู
• Code Upload Fails:
  • Verify that the correct board type (ESP8266 NodeMCU 1.0 or similar) and COM port are selected in your IDE.
  • Check that the baud rate is set correctly (e.g., 115200 for uploads).
  • Ensure no other application is using the serial port.
• ปัญหาการเชื่อมต่อ Wi-Fi:
  • Double-check Wi-Fi SSID and password in your code.
  • Ensure the Wi-Fi network is 2.4GHz, as ESP8266 does not support 5GHz.
  • Check signal strength and proximity to the access point.
• พฤติกรรมผิดปกติ/โปรแกรมหยุดทำงาน:
  • Review your code for errors, especially memory management.
  • ตรวจสอบให้แน่ใจว่าระบบจ่ายไฟมีเพียงพอ การจ่ายไฟไม่เพียงพออาจทำให้ระบบไม่เสถียร
  • Avoid applying 5V directly to 3.3V I/O pins without proper level shifting.

8. การบำรุงรักษา

To ensure the longevity and reliable operation of your NodeMCU Development Board, observe the following maintenance guidelines:

• จัดการด้วยความระมัดระวัง: ควรหลีกเลี่ยงการทำกระดานตก หรือการกระแทกอย่างรุนแรง
• การป้องกันไฟฟ้าสถิตย์: Always handle the board in an anti-static environment or take precautions to prevent electrostatic discharge (ESD), which can damage electronic components.
• ให้แห้ง: Protect the board from moisture and humidity. Store it in a dry place.
• ความสะอาด : Keep the board free from dust and debris. Use a soft, dry brush or compressed air for cleaning if necessary. Avoid using liquids.
• แหล่งจ่ายไฟที่เหมาะสม: Always use a stable and appropriate power supply (5V via Micro-USB or Vin pin). Over-voltagอาจก่อให้เกิดความเสียหายที่ไม่สามารถแก้ไขได้
• การควบคุมอุณหภูมิ: Operate the board within its specified temperature range. Avoid extreme heat or cold.

9. การรับประกันและการสนับสนุน

Aideepen provides customer support and warranty services for this product.

• บริการหลังการขาย: You are entitled to 7*24 hours after-sales service and professional product usage guidance.
• ระยะเวลารับประกัน: ผลิตภัณฑ์ทุกชิ้นที่ซื้อจาก Aideepen มาพร้อมระยะเวลารับประกัน 24 เดือน
• การเปลี่ยน: A new replacement can be obtained if there is any quality issue with your item during the warranty period.
• ติดต่อฝ่ายสนับสนุน: For any issues or inquiries, please refer to the contact information provided with your purchase or visit the official Aideepen store page.