Parkside Polishing Set PWP 90 B2 Instruction Manual

การแนะนำ

This instruction manual provides essential information for the safe and effective use of your Parkside Polishing Set PWP 90 B2. Please read this manual thoroughly before first use and keep it for future reference. This set is designed for use with the Parkside PWP 90 B2 polisher (LIDL IAN 104097, 273271) for vehicle care, specifically for applying polishes and waxes.

ภาพที่ 1: จบแล้วview of the Parkside Polishing Set PWP 90 B2, showing the polishing plate, sponge cap, and synthetic fur cap.

เนื้อหาแพ็คเกจ

The Parkside Polishing Set PWP 90 B2 includes the following components:

• 1x Polishing Plate: The base attachment for the polisher.
• 1x Sponge Cap: Designed for applying polishes.
• 1x Synthetic Fur Cap: Designed for waxing and buffing.

คำแนะนำการตั้งค่า

Follow these steps to correctly attach the polishing accessories to your Parkside PWP 90 B2 polisher:

1. Ensure Polisher is Off: Before attaching any accessories, ensure your Parkside PWP 90 B2 polisher is switched off and unplugged from the power source to prevent accidental startup.
2. Attach Polishing Plate: Securely fasten the polishing plate to the polisher's spindle. Refer to your polisher's manual for specific attachment instructions if needed.
3. Select and Attach Cap:
   • For polishing, use the หมวกฟองน้ำ. Carefully stretch the sponge cap over the polishing plate, ensuring it fits snugly and is centered.
   • For waxing or buffing, use the Synthetic Fur Cap. Stretch the synthetic fur cap over the polishing plate, ensuring a secure and even fit.
4. ตรวจสอบสิ่งที่แนบมา: Gently tug on the attached cap to ensure it is firmly secured to the polishing plate and will not detach during operation.

Image 2: The sponge cap, used for applying polishing compounds.

Image 3: The synthetic fur cap, ideal for waxing and buffing surfaces.

คำแนะนำการใช้งาน

This section outlines the general procedure for using the polishing set. Always refer to your polisher's specific operating instructions and the polish/wax product's guidelines.

General Polishing Procedure:

1. เตรียมพื้นผิว: Ensure the surface to be polished is clean, dry, and free of dirt or debris.
2. ทาเล็บ: Apply a small amount of polishing compound directly onto the sponge cap or the surface area to be polished. Do not over-apply.
3. เริ่มขัดเงา: Place the polisher with the sponge cap flat on the surface before turning it on. Start at a low speed and gradually increase as needed.
4. Polish Area: Move the polisher in a consistent, overlapping pattern (e.g., cross-hatch) over the surface. Apply light, even pressure. Avoid pressing too hard, as this can generate excessive heat.
5. ติดตามความคืบหน้า: Continuously check the surface for desired results.
6. ปิดเครื่องขัดเงา: Before lifting the polisher from the surface, turn it off.
7. Wipe Residue: Use a clean microfiber cloth to wipe off any polish residue.

General Waxing/Buffing Procedure:

1. เตรียมพื้นผิว: Ensure the surface is clean and dry, ideally after polishing.
2. ทาแว็กซ์: Apply a thin, even layer of wax to the synthetic fur cap or directly to the surface.
3. เริ่มขัดเงา: Place the polisher with the synthetic fur cap flat on the surface before turning it on. Use a low to medium speed.
4. Wax/Buff Area: Move the polisher in a consistent, overlapping pattern. The synthetic fur cap is excellent for spreading wax evenly and buffing to a high shine.
5. ปิดเครื่องขัดเงา: Before lifting the polisher from the surface, turn it off.
6. Final Buff (Optional): For an even higher shine, a final hand buff with a clean, dry microfiber cloth may be performed.

หมายเหตุด้านความปลอดภัยที่สำคัญ:

• ควรสวมใส่อุปกรณ์ป้องกันส่วนบุคคล (PPE) ที่เหมาะสมเสมอ เช่น แว่นตานิรภัย
• Do not use the polisher near flammable liquids or gases.
• Avoid applying excessive pressure, which can damage the surface or the polisher.
• Regularly check the caps for wear and tear. Replace them if they become damaged or ineffective.

การบำรุงรักษาและการดูแล

Proper maintenance extends the life of your polishing set and ensures optimal performance.

1. Cleaning Caps:
   • After each use, remove the sponge and synthetic fur caps from the polishing plate.
   • Wash the caps thoroughly with warm water and a mild detergent. Gently squeeze out excess product and dirt.
   • Rinse thoroughly until all soap residue is gone.
   • Allow the caps to air dry completely before storing or reusing. Do not tumble dry or expose to direct heat.
2. Cleaning Polishing Plate: Wipe the polishing plate with a damp cloth to remove any residue. Ensure it is dry before storage.
3. พื้นที่จัดเก็บ: Store the polishing set components in a clean, dry place, away from direct sunlight and extreme temperatures.
4. การตรวจสอบ: Periodically inspect the caps for signs of wear, tears, or hardening. Replace them if they are no longer effective or show damage.

การแก้ไขปัญหา

This section addresses common issues you might encounter with your polishing set.

ข้อมูลจำเพาะ

Key technical details for the Parkside Polishing Set PWP 90 B2:

ข้อมูลการรับประกัน

Specific warranty details for the Parkside Polishing Set PWP 90 B2 are not provided in this manual. For information regarding the product warranty, please refer to the documentation included with your purchase, the product packaging, or contact the manufacturer directly. Warranty terms may vary by region and retailer.

การสนับสนุนลูกค้า

If you encounter any issues or have questions regarding your Parkside Polishing Set PWP 90 B2 that are not covered in this manual, please contact the retailer where you purchased the product or the manufacturer, Parkside, for assistance. Please have your product model number (PWP 90 B2) and ASIN (B07L4LNNXP) ready when contacting support.

You may also visit the official Parkside webเว็บไซต์นี้เหมาะสำหรับค้นหาข้อมูลเพิ่มเติมหรือข้อมูลการติดต่อ