HOBBYWING JUSTOCK G2.1 Brushless Motor Instruction Manual

การแนะนำ

This manual provides essential information for the proper installation, operation, and maintenance of your HOBBYWING JUSTOCK G2.1 brushless motor. Designed for 1/10 and 1/12 scale RC vehicles, this motor is compliant with ROAR and IFMAR rules, featuring zero timing for spec racing.

Key features include a heat-resistant magnet attached aluminum case, double insulated windings, high precision bearings, and a robust rotor structure for durability and performance. The built-in Hall sensor and non-adjustable end bell ensure smooth and linear power delivery.

ข้อมูลด้านความปลอดภัย

คำเตือน: This item is not a toy. It contains small parts and electrical components. Adult supervision is recommended during assembly and operation, especially for users under 16 years of age.

• Always disconnect the battery before performing any maintenance or installation.
• ตรวจสอบให้แน่ใจว่ามีการระบายอากาศที่เหมาะสมระหว่างการทำงานเพื่อป้องกันความร้อนสูงเกินไป
• หลีกเลี่ยงการสัมผัสกับชิ้นส่วนที่เคลื่อนไหวระหว่างการทำงาน
• Do not expose the motor to water or excessive moisture unless specifically designed for such conditions.
• Use only compatible electronic speed controllers (ESCs) and batteries.

การติดตั้งและการตั้งค่า

Proper installation is crucial for optimal performance and longevity of your motor.

1. การติดตั้งมอเตอร์

Securely mount the motor to your vehicle's motor mount using appropriate screws. Ensure the motor is aligned correctly with the pinion gear to prevent excessive wear and friction.

รูปที่ 1: ด้านข้าง view of the HOBBYWING JUSTOCK G2.1 Brushless Motor, showing the sensor port and mounting holes.

2. การเชื่อมต่อสายไฟ

Connect the motor to your Electronic Speed Controller (ESC) according to the ESC's instructions. Typically, the three motor wires (A, B, C) connect to the corresponding output terminals on the ESC. Ensure correct polarity and secure connections.

• สายเซนเซอร์: Connect the sensor cable from the motor to the sensor port on your ESC. This is essential for sensored operation and smooth low-speed performance.
• การเชื่อมต่อแบตเตอรี่: Connect your battery to the ESC, ensuring correct polarity. The motor supports 2S-3S LiPo batteries.

รูปที่ 2: ด้านบน view of the HOBBYWING JUSTOCK G2.1 Brushless Motor, indicating the A, B, C terminals for ESC connection and the fixed timing end bell.

3. Gear Ratio Selection

Select an appropriate gear ratio for your vehicle and track conditions. Refer to your vehicle's manual or consult experienced users for recommendations. Incorrect gearing can lead to overheating and reduced performance.

คำแนะนำการใช้งาน

Once installed and connected, the HOBBYWING JUSTOCK G2.1 motor is ready for operation. This motor is designed for zero timing spec racing.

• การเพิ่มพลังเริ่มต้น: เปิดเครื่องส่งสัญญาณก่อน จากนั้นจึงเชื่อมต่อแบตเตอรี่เข้ากับ ESC
• การสอบเทียบ: If necessary, calibrate your ESC with the motor and transmitter according to your ESC's manual.
• วิ่ง: Operate your RC vehicle as usual. Monitor motor temperature during initial runs to ensure proper gearing and setup.
• ปิดระบบ: ก่อนอื่นให้ถอดแบตเตอรี่ออกจาก ESC จากนั้นปิดเครื่องส่งสัญญาณของคุณ

This motor is perfectly matched with the HOBBYWING XR10-JUSTOCK ESC for all zero timing spec racing and is also compatible with other HOBBYWING electronic speed controllers and other brands.

การซ่อมบำรุง

Regular maintenance will prolong the service life and improve the operating efficiency of your JUSTOCK motor.

• การทำความสะอาด: The motor features a detachable structure design for daily cleaning. Carefully disassemble the motor (if comfortable) to clean out dirt, dust, and debris from the internal components. Use compressed air or a soft brush.
• การตรวจสอบตลับลูกปืน: Periodically check the motor bearings for smooth operation. Replace worn or noisy bearings to maintain efficiency.
• O-Ring Seal: The silicone O-ring seal between the end bell and stator helps conduct inner heat and prevent dust. Ensure it is clean and properly seated.
• ตรวจสอบการเชื่อมต่อ: Regularly inspect all wiring connections for signs of wear, corrosion, or looseness.

การแก้ไขปัญหา

If you encounter issues with your motor, consider the following common troubleshooting steps:

• มอเตอร์ไม่ทำงาน:
  • Check all wiring connections between the motor, ESC, and battery.
  • ตรวจสอบให้แน่ใจว่าแบตเตอรี่ชาร์จแล้วและเชื่อมต่ออย่างถูกต้อง
  • Verify ESC calibration with the transmitter.
  • Inspect the sensor cable for damage or improper connection.
• ความร้อนสูงเกินไป:
  • Check your gear ratio; it might be too aggressive.
  • Ensure there is adequate airflow to the motor.
  • Verify that the motor is not binding or experiencing excessive friction.
• Irregular Performance / Cogging:
  • Re-check sensor cable connection and ensure it's not damaged.
  • Ensure all motor phase wires are securely connected.
  • ตรวจสอบดูว่ามีเศษสิ่งสกปรกอยู่ภายในมอเตอร์หรือไม่

If problems persist, contact HOBBYWING customer support or consult with an experienced RC hobbyist.

ข้อมูลจำเพาะ

การรับประกันและการสนับสนุน

Legal Disclaimer and Warranty Information

Because HOBBYWING has no control over the use, installation, or maintenance of this product, no liability may be assumed for any damage or losses resulting from the use of the product. HOBBYWING does not assume responsibility for any losses caused by unauthorized modifications to its products. HOBBYWING reserves the right to modify product design, appearance, features, and usage requirements without prior notification.

HOBBYWING is only responsible for the product cost. Products purchased from Hong Kong / Chinese retailers may not conform to CE / North America regulations, and such products are deemed non-warranty. Discount / auction stores such as eBay are considered "non-authorized sales channels" in North America, and products purchased from these channels are also deemed non-warranty.

การสนับสนุนลูกค้า

For technical assistance or further inquiries, please visit the official HOBBYWING website or contact your local authorized dealer. Ensure you have your product model number (30408013) and purchase details available when seeking support.