TEZarrE TK61-Pro Three-Mode Mechanical Keyboard
Product Diagram
Equipment Name
Wired connection indication: Gaming Keyboard BT3.0 connection indication: BT3.0KB
2.4G connection indication: 2.4G Wireless Device BT5.0 connection indication: BT5.0KB
Product Specifications
➊ Keycap: 61 keys, Optical switch
➋ Valid distance: s 10m 360°(With external environmental interference)
➌ Bluetooth reconnection time: s 5s
| Bluetooth | 2.4G |
| Compatible with all Bluetooth Dongle in the market, built-in Bluetooth module in notebook, Bluetooth 5.0 needs to support WINB or above system, tablet and mobile phone, etc | According to sub standard protocol, compatible with Windows2000 and MAC operating system; |
➍ Compatibility:
➎ Anti-ghosting: All modes and devices support anti-ghosting
➏ Working voltage: 3.7V
➐ Working mode: wired, 2.4G, Bluetooth 3.0 mode, Bluetooth 5.0 mode
➑ RF power: when keyboard working RF power is 30dbm; when receiver working RF power is 30dbm
➒ Working frequency: 2402/2446/2479
| interface | 2.4G |
| USB | compatible with Windows2000 above and MAC operation system, BLE support WINS or above |
➓ System requirements:
Connection Ways
Bluetooth Mode
- Turn on the keyboard
- Hold down the
(kept pressed more than 3 seconds). - Be paired with BT5.0KB. Until the key lights on for ten seconds
Note: Considering battery health, please turn off the switch on the back if you don’t use it over a long period of time.
USB2.4G Mode
- Turn on the keyboard
- Hold down the
+ 
(kept pressed more than 3 seconds) - Be paired with 2.4G Wireless Device. Until the key lights on for ten seconds
Note: Considering battery health, please turn off the switch on the back if you don’t use it over a long period of time.
Wired Mode
- Turn off the keyboard.
- Connect type-c cable, connect successfully.
Combination Keys
RGB Backlight Setting
Arrow Keys
Multimedia Control
Function Key-1
Function Key-2
Power Indicator
Electrical Specifications (for reference only)
| Charge current | 540-580mA |
| Wired lights on mode current | 110.2mA |
| 2.4G lights on mode current | 168.6mA |
| 2.4G sleep mode current | 4.37mA |
| Bluetooth 3.0 lights on mode current | 168.2mA |
| Bluetooth 3.0 sleep mode | 3.87mA |
| Bluetooth 5.0 lights on mode current | 168.4mA |
| Bluetooth 5.0 sleeping current | 3.87mA |
| Turn off the backlight current | 39.8mA |
Detailed Operation
➊ 2.4G Pairing:
After the keyboard turns on, pressing 
+ 5s into the pairing mode, while the indicator flashing, then inserting the receiver, pairing successful, the indicator lights on for 10s. If no pairing devices have been found, after 3Os, exit the pairing mode and the indicator lights off, the keyboard turn to sleep mode.
➋ Bluetooth Pairing:
Long press 
for 5s, the keyboard turns into the pairing mode, the indicator flashing. when succefully connected with devices, indicator lights on for 10s, if no pairing devices have been connected, the indicator lights off, the keyboard turns to the sleep mode. The Bluetooth names are BT3.O and BT5.O. Please connect as required.
➌ Reconnection Indication:
After keyboard turns on or wakes from sleep mode, Pairing directly with previous devices;
If cannot connect with the devices, The keyboard turns to sleep mode. The keyboard will continue pairing with devices after awakened;
In the process of the 2.4G reconnection, The white indicator slowly flashing. After connected, The indicator lights on for 10s, During the reconnection process, Press keys can extend the reconnection process. Connection takes 10s after pressing the key. If reconnection failed, The indicator lights off, Turn to sleep mode, If pairing successes , The keyboard will turn to the pairing mode again, If failure, The keyboard turns to the sleep mode, But will retain the last pairing data;
Bluetooth white light slowly flashes in the reconnection process, The light is normally on 10s, In the reconnection process, Press keys can extend the process, Connection takes 10s after pressing keys, If failure, The indicator lights off, The keyboard turns to sleep mode, Again after a match such as in pairing mode, After failed to pair, the keyboard turns to sleep mode. but will retain the last match data, If pairing successed, The keyboard will turn to the pairing mode again, If failure, The keyboard turns to the sleep mode, But will retain the last pairing data.
➌ Backlight Mode:
Pressing +
combination key Switching light mode sequence: light wave
(default), always bright, breath, ripple, raindrop, snake, follow, convergence, neon, laser, sine
wave, slanting wind and rain, colorful fountain, peaks and valleys, flowers blooming.
Normal light mode can not adjust the backlight speed; neon, wind and rain, music rhythm can not adjust the backlight color, the rest of the backlight mode can adjust the speed, brightness and color, brightness a total of seven orders, the default maximum brightness; speed a total of 5 orders, the default 3rd order speed, color order: seven colors, ice blue, red, green, blue, orange, purple, yellow.
Remap Keys
The keeb comes with a custom software for windows which allows you to remap keys, edit macros plus other functions! Please use the link to access the tutorial video and the software for windows.
Website
www.tezarre.com
info@tezarre.com
Documents / Resources
 |
TEZarrE TK61-Pro Three-Mode Mechanical Keyboard [pdf] User Guide TK61-Pro Three-Mode Mechanical Keyboard, TK61-Pro, Three-Mode Mechanical Keyboard, Mechanical Keyboard, Keyboard |
