Parts list
| 1 | 9-inch screen |
| 2 | Camera and extension cable |
| 3 | Power harness |
| 4 | Trim removal tool |
| 5 | Fixed bracket |
1. Tools required for installation
Plastic warping board, T20 sleeve screwdriver, threading tape, tape
2. Second, installation precautions
The version 23 years after the model year has a distinction between the rear with or without OBD connectors, which should be paid attention to when installing. The installation positions are different (shared by cable harnesses). For details, see installation instructions.
M3\MY TES-F9C Pro Carplay dashboard Disclaimer and Precautions
Warnings and Disclaimers
Important notice: Welcome to purchase the company’s products, in order to protect the legitimate rights and interests of users, in this special reminder to users, please be sure to carefully read and fully understand the terms of this statement before using this product. If you use this product, your use behavior will be regarded as the acceptance of the entire content of this statement, and agree to accept the following terms of this statement, and bear the effect caused by irregular use of the payment. Company reserves the right to update the above documents. Please be sure to operate this product according to the instructions. Precautions for use
- Check whether the product list is complete and damaged before installation.
- the installation instructions may be slightly different from the actual operation. If there are any differences, please refer to the actual situation or contact us.
- Warning: Do not disassemble any parts by yourself, any improper operation is not covered by the warranty.
- Watch the installation video and instruction manual before installing the product.
- check whether the installed product function is normal.
 Installation manual |
 Installation video |
| https://qr61.cn/ovcXRg/qyujPfZ | https://qr03.cn/FOngKX |
Customer Service :
phone : +1(626)412-7352
+1 7143179647
Email: service@tesstudio.com
M3\MY TES-F9C Pro Carplay Instrument Panel Installation Instructions
 |
 |
| 1. Remove the triangular panel on the left side (the same goes for the right side) | 2. Remove the instrument middle trim panel |
 |
 |
| 3. Take out the passenger rectangular trim panel | 4. Remove the clips on the passenger door trim panel and remove the door sill trim panel (the same applies to the left and right) |
 |
 |
| 5. Take out the positioning sticker | 6. Place the sticker correctly on the driver’s side front dash trim plate |
 |
 |
| 7. The three points on the sticker correspond to the three holes on the dash trim plate. | 8. Align the wiring harness plugs on the screen and pass them through |
 |
 |
| 9. The screen is stuck in, and the back of the trim panel looks like this | 10. Take out the fixing bracket and tighten the screws one by one. |
Intel version
 |
 |
| 11. Use T20 to unscrew the fixing screws and buckles of the passenger floor. | 12. Unplug the second gray plug on the computer board and plug it in |
AMD version
 |
 |
| 13. Connect the plug to the white plug under the A-pillar of the right front seat | 14. Insert the plug into the blue plug under the A-pillar of the right front seat |
 |
 |
| 15. Plug in the corresponding plug according to your car version, and then run the wiring harness along the edge to the front of the steering wheel. |
16 . Each plug has a corresponding label. You must check it first. If it is correct, just plug in the plug according to the color. If you find anything wrong, please contact us (the yellow wire harness is optional on the front view) |
 |
 |
| 17、Put the central control instrument with the screen installed back into the central control position and power it on to test if it is normal | 18. After restoring the instrument panel, tear off the hole fixing stickers |
The front-view camera is an optional product. If you do not need to install a front-view camera, you do not need to follow the steps below
 |
 |
| 19. Remove the air intake trim panel screws. | 20. Use a No. 10 socket to unscrew the four fixing |
 |
 |
| 21. Pry open the buckle that fixes the front trunk | 22. Unplug the front trunk button and take out the front trunk |
 |
 |
| 23. Pass the camera harness through the heat dissipation grille hole into the cabin. | 24. Use double-sided tape to stick the camera in the center of the license plate, align the position with the fixing screw (clean it before pasting) |
 |
 |
| 25. Cut off the raised position of the rubber plug as shown in the picture ( the location is in the upper right corner of the passenger frunk) | 26. Thread the threading tape from the cut position ( Don’t break the rubber plug, otherwise it will be difficult to snap it back in) |
 |
 |
| 27. Pull out the threading strap from the passenger side (tie the extension harness over there in the cabin) | 28. Walk along the main wiring harness to the front of the steering wheel (the wiring harness can be fixed with tape to prevent abnormal noise) |
 |
 |
| 29. Plug the extension cord into the camera plug (fix the excess wire harness) | 30. Plug the other end into the screen plug. The yellow wire harness is the front-view plug (fix the excess wire harness) |
F9C Pro Carplay version instrument screen -FAQ troubleshooting guide
| Fault | Reason | Solution |
| Black screen (The screen does not light up after installation) | Other factors cause the microprocessor to work abnormally | Restart key |
| After the host plug was unplugged, it was not plugged back in for 5 minutes. | Connect the wiring harness, lock the car for 2 hours, keep the mobile phone and remote control key more than 20 meters away from the car, and check after 2 hours to see if the screen can be lit. |
|
| The host or screen plug is not tightly plugged in | Reconnect the console plug | |
| Start without display | Background data error | Reconnect the console plug |
| The original car information is not synchronized or not displayed | The power line protocol line is blocked | Replug the cable and check the cable interface |
| How to switch between day and night mode |
Push the right scroll wheel to the right to enter the settings interface |
Set to manual or automatic mode |
| Dimming | Push the right scroll wheel to the right to enter the settings interface | Set to desired brightness |
| How to switch body color? | Push the right scroll wheel to the right to enter the settings interface | Set desired color |
| How to switch UI interface | Press the right scroll wheel to the right to enter the UI selection interface | Set up the required UI |
| Why can’t I enter the front view? | Set the front-view camera to turn off | Open the front camera on the settings page |
| What should I do if the machine crashes? | System breakdown | Press and hold the left scroll wheel to the left to force restart. |
| How to adjust the volume | 1. There are shortcuts on the right side of the interface that can be adjusted directly by touching 2. Rotate the left wheel up and down to increase or decrease the volume. |
Warranty and support
Tesstudio offers 1-year Extended Warranty. Send us your customer number to receive a full 1 year warranty
Email: service@tesstudio.com
Our Website:tesstudio.COM
Designed by TESSTUDIO
Documents / Resources
 |
TES STUDIO TES-F9C Pro CarPlay Screen Dashboard Display [pdf] User Manual TES-F9C Pro, TES-F9C Pro CarPlay Screen Dashboard Display, TES-F9C Pro, CarPlay Screen Dashboard Display, Dashboard Display, Display |