Tera Electronic Time Clock

Package Contents
- Electronic Time Clock
- Time Card
- Ribbon Cassette
Please do not hesitate to contact us if you have any questions.
Important Notice: Please include your Order Number and Product Model Number in the email.
Official Customer Service
- Email Address: info@tera-digital.com
- Cell: +1 (909) 242-8669
- Whatsapp: +1 (626) 438-1404
Follow us:
- Instagram: tera_digital
- Youtube: Tera Digital
- Twitter: Tera Digital
- Facebook: Tera
User manuals are available in Spanish, French, Italian, and German, and can be downloaded from our website.
You may visit our official website via the link below or by scanning the given QR code: Website: https://www.tera-digital.com

Appearance and Display Layout

- Latch
- Day of the Week Indication
- Current Time
- Current Date
- Printing Color
- Printing Position and Buttons

- Mounting Holes
- Sticker
- Reserved Holes for Backup Battery Lock
- Power Supply Port
When in program mode
- Parameters
- Current Parameter Group
Installing the ribbon cassette
- Step 1: press [4] button.
- Step 2: Switch the latch to the ON position.
- Step 3: remove the cover.

- Step 4: remove the protective film on the installed ribbon cassette.
- Step 5: pull A and B backward and hold, and pull C to take out the ribbon cassette.
- Step 6: turn the knob of the new ribbon cassette in the same direction as shown by the arrow near the knob to tighten the ribbon. (Note: Must not turn the knob in the opposite direction. Improper handling causes malfunction of a ribbon cassette.)
- Step 7: make sure the ribbon is between the print head (E) and the ribbon mask(F)
- Step 8: push the ribbon cassette until it snaps into the clasps on both sides.
- Step 9: turn the knob of the ribbon cassette in the direction of the arrow to tighten the ribbon
Introduction
How to Enter Program Mode
- Long press [6] Button until all the indicators flash three times and the beeper emits three beeps, to enter the program mode.
- (If you have set a four-digit password, you should first enter the password)
- (If you cannot remember the password, please enter 9813 to activate program mode)
How to Adjust the Parameters
Press the [1] button to increase the flashing number or the [2] button to decrease the flashing number. When you have determined the appropriate value, press [3] button or [4] button to save the change and move to the next or previous parameter group
| Group | Description |
| 00 | Year |
| 01 | Month |
| 02 | Day |
| 03 | Hour |
| 04 | Minute |
| 05 | Alarm Duration (0-99s) |
| 06 | Alarm 1 |
| 07 | Alarm 2 |
| 08 | Alarm 3 |
| 09 | Alarm 4 |
| 10 | Alarm 5 |
| 11 | Alarm 6 |
| 12 | Time when the clock shifts to the next row |
| 13 | Time when the clock shifts to the 1st column |
| 14 | Time when the clock shifts to the 2nd column |
| 15 | Time when the clock shifts to the 3rd column |
| 16 | Time when the clock shifts to the 4th column |
| 17 | Time when the clock shifts to the 5th column |
| 18 | Time when the clock shifts to the 6th column |
| 19 | Time when printing in red (In) |
| 20 | Time when printing in black (Out) |
| 21 | Time when printing in red (In) |
| 22 | Time when printing in black (Out) |
| 23 | Time when printing in red (In) |
| 24 | Time when printing in black (Out) |
| 25 | Alarm 7 |
| 26 | Alarm 8 |
| 27 | Alarm 9 |
| 28 | Alarm 10 |
| 29 | Alarm 11 |
| 30 | Alarm 12 |
| 31 | Printing Position |
| 32 | Card Side Detection |
| 33 | Standard Shift and Three Shifts |
| 34 | Password |
Note:
The 12th parameter group means the time when the clock will move the print head to the position where the first column of the card is when placed in the card slot. By default, the time is set as 00:00 and it is not necessary to change it unless the schedule is three shifts, in which case the 12th parameter should be set as a time between the quitting time of the last work shift and the starting time of the first work shift. 32nd parameter group: Card Side Detection. There are only two parameters available: 00:00 (Disable detection) and 00:01 (Enable detection).
Quick Setup
Connect the time clock to a power supply, hold the [6] button until all the indicators flash 3 times and the beeper emits 3 beeps, to enter program mode.
- On the lower left corner of the display appears 00, which indicates Press [1] button or [2] button to adjust the last flashing two digits to the current year. Press the [3] button to save the change and move to the next parameter group.
- On the lower left corner of the display appears 01, which indicates Month. Press the [1] button or [2] button to adjust the flashing number to the current month. Press the [3] button to save the change and move to the next parameter
- On the lower left corner of the display appears 02, which indicates Day. Press the [1 ] button or [2] button to set up for the Day. Press the [3] button to save the change and move to the next parameter group.
- On the lower left corner of the display appears 03, which indicates Hour. Press the [1] button or [2] button to set up for Hour. Press the [3] button to save the change and move to the next parameter group.
- On the lower left corner of the display appears 04, which indicates Press [1] button or [2] button to set up for Minute. Press the [3] button to save the change and move to the next parameter group.
- On the lower left corner of the display appears 05, which indicates the Duration of a The default value is 00:10, which means the alarm will last for 1Os. Press [1] button or [2] button to extend or shorten the duration. Press the [3] button to save the change and move to the next parameter group.
- On the lower left corner of the display appears 06, which indicates the time when an Alarm starts. Press the [1] button or [2] button to change the Hour and then press the [3] button to continue to set up for Minute. Lastly, press the [3] button to save the change and move to the next parameter group. (If you don’t need an alarm anymore, press the [5] button while the lower left corner of the display shows 06 and the Hour parameter is flashing, and the display will show–:–, meaning that the alarm is removed.)
- On the lower left corner of the display appears 12, which indicates the time when the clock will move the print head to the next row. It is not necessary to change the default parameter if in a standard schedule. Simply press [3] to save the change and proceed to set up for other parameters.
- On the lower left corner of the display appears 13, which indicates the time when the clock will move the print head to the 1st column. Press [1] button or [2] button to
Note: From the 6th group to the 11th group and the 25th group to the 30th group are all alarm groups, so the configuration steps are the same. Note that the time when the clock shifts to the 1st column must be earlier than the shift starting time. (The 13th group through 18th group can be set in the same way.) - On the lower left corner of the display appears 19, which indicates the time when the print head inside the clock will print in red. Press the [1] button or [2] button to change the Hour and then press the [3] button to continue to set up for Minute. Lastly, press [3] to save the change and move to the next parameter group. ( The 19th group through the 24th group can be set in the same way.)
- On the lower left corner of the display appears 31 , indicating the printing The default value is 00:05 and the printing is often in the center of the cell on the card Press the [1] button or [2] button to adjust the parameter so as to slightly change the printing position. Press the [3] button to save the change and move to the next parameter group. (The greater the number is, the higher the printing position will be.)
- On the lower left corner of the display appears 32, which indicates the feature that detects the side of the card When this feature is enabled, the time clock will only accept the card which is placed with the correct printing side to the front. If the card is placed with the printing side to the back, it will not pull in the card. (Normally, if placed correctly, the time card is automatically pulled in, printed, and then ejected) If you don’t want to change the setting, simply press the [3] button to save and move to the next parameter group.
- On the lower left corner of the display appears 33, which indicates work shifts. By default, the parameter is 00:00, which means standard shift. If you need to enable three shifts, just change the parameter to 00:01 by pressing the [1] button, then press [3] to save the change and move to the next parameter group.
- On the lower left corner of the display appears 34, which indicates the password. By default, there is no password. If you want to protect the time clock, you may add a password by entering four-digit codes using the [1 ] button and [2] button. When configuration is done, press [3] to save the change and move to the next parameter group. By this step, all the parameters are configured and you can hold the [6] button to exit program mode. (If you want to remove the password, just press the [5] button when the display shows the 34th group of parameter. The display will show–:-, meaning the parameter is null.)
- To reset the time clock, hold [1][5][6] buttons at the same time when the clock is in program mode.
FREQUENTLY ASKED QUESTIONS
What is the Tera Electronic Time Clock?
How does the Tera Electronic Time Clock work?
Is the Tera Electronic Time Clock suitable for small businesses?
Can the Tera Electronic Time Clock calculate employee work hours and overtime?
Is the Tera Electronic Time Clock compatible with biometric authentication methods?
Can the Tera Electronic Time Clock integrate with payroll software?
Does the Tera Electronic Time Clock have reporting capabilities?
Is the Tera Electronic Time Clock web-based or standalone?
Can employees access their time records on the Tera Electronic Time Clock?
Is the Tera Electronic Time Clock compliant with labor laws and regulations?
What is the warranty for the Tera Electronic Time Clock?
Is the Tera Electronic Time Clock user-friendly and easy to set up?
Can the Tera Electronic Time Clock handle multiple shifts and schedules?
Is the Tera Electronic Time Clock suitable for remote or mobile workforce management?
Is the Tera Electronic Time Clock compatible with different payment methods?
Does the Tera Electronic Time Clock offer support and training for businesses?
DOWNLOAD THE PDF LINK: Tera Electronic Time Clock Operation Manual
References
- User Manualmanual.tools

Why is it not feeding when it is 16th to 31st of the month?
Why is the time clock not feeding cards from the 16th to the 31st of the month?
This issue is typically related to the Card Side Detection feature or the orientation of the time card. Most standard time cards are double-sided, with one side for days 1-15 and the other for days 16-31.
If your device is not feeding the card during the second half of the month, please check the following:
00:00disables detection, while00:01enables it. If you are having trouble with the machine accepting the card, you may try setting this to00:00.If the card still does not pull in automatically, ensure the ribbon cassette is properly installed and that there are no obstructions in the card slot.
Read the full Q&A page