TELTONIKA FMM920 Tracker Smart and Small User Guide

The FMM920 is a small and smart tracker designed for telematics applications. It features various inputs and outputs for monitoring and controlling devices.

Product Usage Instructions

Know Your Device:
The device includes various components such as a power cable, micro-USB port, LED indicators, battery socket, and micro-SIM slot. Refer to the manual for detailed pinout information.

Set Up Your Device:

Micro-SIM Card Installation:
1. Carefully remove the FMM920 cover using a plastic pry tool.
2. Insert the Micro-SIM card with the cut-off corner facing forward into the slot.
3. Remove the adhesive tape protection.
4. Place the battery inside the casing and connect it to the PCB.
5. Reattach the cover to complete the setup.

PC Connection (Windows):
1. Download and install the necessary USB drivers for Windows from the provided link.
2. Connect the device to your computer for configuration.
Configuration:
Customize device settings using Teltonika Configurator software on a Windows OS. Ensure you have the required .NET Framework installed.

KNOW YOUR DEVICE

PINOUT

WIRING SCHEME

SET UP YOUR DEVICE

COVER REMOVAL
Gently remove the FMM920 cover using a plastic pry tool from both sides.

MICRO-SIM CARD INSERT
Insert Micro-SIM card as shown with PIN request disabled or read Security info1 how to enter it later in Configurator. Make sure that the Micro-SIM card cut-off corner is pointing forward to the slot. wiki.teltonika-gps.com/view/FMM920_Security_info
REMOVING PROTECTION
Remove the adhesive tape protection.

PLACING BATTERY
Place the battery inside the casing of the FMM920. Make sure the adhesive tape sticks to the casing.
CONNECTING BATTERY
Connect the internal battery to the FMM920 PCB.

ATTACHING COVER BACK
Attach the device cover back. The device is ready \to be connected

PC CONNECTION (WINDOWS)

Power-up FMM920 with DC voltage (10 – 30 V) power supply using power wires. LEDs should start blinking, see “LED indications1”.

Connect the device to the computer using a Micro-USB cable or Bluetooth® connection:
- Using Micro-USB cable
- You will need to install USB drivers, see “How to install USB drivers (Windows)2”
- Using Bluetooth® wireless technology
- FMM920 Bluetooth is enabled by default. Turn on the Bluetooth® connection on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “FMM920_last_7_imei_digits”, without LE in the end.
- Enter default password 5555, press Connect, and then select Done.
You are now ready to use the device on your computer.

HOW TO INSTALL USB DRIVERS (WINDOWS)

Please download COM port drivers from here1.
Extract and run TeltonikaCOMDriver.exe.
Click Next in the driver installation window.
In the following window click the Install button.
Setup will continue installing the driver and eventually, the confirmation window will appear. Click Finish to complete the setup.

wiki.teltonika-gps.com/images/d/d0/TeltonikaCOMDriver.zip

CONFIGURATION

At first, the FMM920 device will have default factory settings set. These settings should be changed according to the user’s needs. The main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses the prerequisite MS .NET Framework. Make sure you have the correct version installed.

Downloaded Configurator will be in a compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking ? in the right bottom corner.The configuration process begins by pressing on the connected device.

After connection to Configurator Status window will be displayed. Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5, etc. FMM920 has one user-editable profile, which can be loaded and saved to the device. After any modification of configuration, the changes need to be saved to the device using the Save to Device button. Main buttons offer the following functionality:

Load from the device – loads configuration from the device.
Save to device – saves the configuration to the device.
Load from file – loads configuration from file.

Save to file – saves the configuration to file.
Update firmware – updates the firmware on the device.
Read records – reads records from the device.

Reboot devicrestartarts the device.
Reset configuration – sets device configuration to default.

The most important configurator section is GPRS – where all your server and GPRS settings6 can be configured and Data Acquisition7 – where data acquiring parameters can be configured. More details about FMM920 configuration using Configurator can be found in our Wiki8.

QUICK SMS CONFIGURATION

The default configuration has optimal parameters present to ensure the best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it:

Note:
Before SMS text, two space symbols should be inserted.
GPRS SETTINGS:

2001 – APN

2002 – APN username (if there are no APN usernames, an empty field should be left)
2003 – APN password (if there are no APN passwords, an empty field should be left)

SERVER SETTINGS:

2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)

DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION:

VEHICLE MOVEMENT will be detected by accelerometer
IGNITION WILL BE DETECTED by vehicle power voltage between 13,2 – 30 V

DEVICE MAKES A RECORD OF MOVING IF ONE OF THESE EVENTS HAPPENS:

300 seconds passes
VEHICLE DRIVES 100 meters

VEHICLE TURNS 10 degrees
SPEED DIFFERENCE between the last coordinate and current position is greater than 10 km/h

DEVICE MAKES A RECORD ON STOP IF:

1 HOUR PASSES while the vehicle is stationary and ignition is off

RECORDS SENDING TO SERVER:

IF THE DEVICE HAS MADE A RECORD it is sent to the server every 120 seconds

After successful SMS configuration, the FMM920 device will synchronize time and update records to the configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.

MOUNTING RECOMMENDATIONS

CONNECTING WIRES

Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.

If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
Wires cannot be connected to the board computers or control units.

CONNECTING POWER SOURCE

Be sure that after the car computer falls asleep, power is still available on the chosen wire. Depending on the car, this may happen in a 5 to 30-minute period.
When the module is connected, measure the voltage again to make sure it did not decrease.
It is recommended to connect to the main power cable in the fuse box.

Use 3A, 125V external fuse.

CONNECTING IGNITION WIRE

Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.

Check if this is not an ACC wire (when the key is in the first position, most of the vehicle electronics are available).
Check if power is still available when you turn off any of vehicles devices.
The ignition is connected to the ignition relay output. As an alternative, any other relay, that has power output when ignition is on, may be chosen.

CONNECTING GROUND WIRE

The ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
If the wire is fixed with the bolt, the loop must be connected to the end of the wire.

For better contact scrub paint from the spot where the loop is going to be connected.

LED INDICATIONS

NAVIGATION LED INDICATIONS

STATUS LED INDICATIONS

BASIC CHARACTERISTICS

gps.com/products/accessories/sensors-beacons

wiki.teltonika-gps.com/view/How_to_connect_OBD_II_Bluetooth_Dongle_to_FMB_device

ELECTRICAL CHARACTERISTICS

SAFETY INFORMATION

This message contains information on how to operate FMM920 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device.

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of the device’s operation.
When connecting the connection (1×5) cables to the vehicle, the appropriate jumpers of the power supply of the vehicle should be disconnected.

Before dismounting the device from the vehicle, the 1×5 connection must be disconnected.
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard.
The device FMM920 is not designed as a navigational device for boats.

Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
All wireless data-transferring devices produce interference that may affect other devices that are placed nearby.
The device must be firmly fastened in a predefined location.

The programming must be performed using a PC with an autonomic power supply
The device must be connected only by qualified personnel.
Installation and/or handling during a lightning storm is prohibited.

The device is susceptible to water and humidity.

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User’s Manual before you start using the device. The full Users Manual version can be found in our Wikil wiki.teItonika-gps.com/view/FMM920

This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste. Para maiores informaØes, consulte o site da
ANATEL www.anatel.gov.br

For more information, see the ANATEL website www.anatel.gov.br
This equipment is not entitled to protection against harmful interference and must not cause interference in duly authorized systems.
The standard aims to provide users with more detailed information than vague marketing terms such as waterproof.

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by I-JAB Teltonika Telematics is under license. Other trademarks and trade names are those of their respective owners.
Hereby, Teltonika declares under our sole responsibility that the above-described product conforms with the relevant Community harmonization: European Directive 2014/53/ELJ (RED).
I-JK Conformity Assessed (UKCA) marking is a conformity mark that indicates conformity with the applicable requirements for above described products sold within Great Britain.

E-Mark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.
The Australian standard AS/NZS 4417.1 and AS/NZS 4417.2 Marking of electrical products to indicate compliance with regulations – General rules for use of the mark provide general requirements for the use of the RCM including the location of the marking on the equipment and its dimensional requirements.
REACH addresses the production and use of chemical substances and their potential impacts on both human health and the environment. Its 849 pages took seven years to pass, and it has been described as the most complex legislation in the Union’s history and the most important in 20 years. It is the strictest law to date regulating chemical substances and will affect industries throughout the world.

The RoHS1 is a directive regulating the manufacture, import, and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use of 10 different hazardous materials (to date)

DECLARATION OF IMEI ASSIGNMENT
The IMEI number is used by a GSM network to identify valid devices and therefore can be used to stop a stolen phone from accessing that network. For example, if a mobile phone is stolen, the owner can call their network provider and instruct them to blacklist the phone using its IMEI number. This renders the phone useless on that network and sometimes other networks too, whether or not the phone’s subscriber identity module (SIM) is changed.

CHECK ALL CERTIFICATES
All the newest certificates may be found in our Wiki2.wiki.teltonika-gps.com/view/FMM920_Certification_%26_Approvals.

WARRANTY

We guarantee our products a 24-month warranty1 period.
All batteries carry a 6-month warranty period.
Post-warranty repair service for products is not provided.

If a product stops operating within this specific warranty time, the product can be:
- Repaired
- Replaced with a new product
- Replaced with an equivalent repaired product fulfilling the same functionality
- Replaced with a different product fulfilling the same functionality in case of EOL for the original product
Additional agreements for an extended warranty period can be agreed upon separately.

WARRANTY DISCLAIMER

Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fault.
Products are intended to be used by personnel with training and experience.
Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance, or inadequate installation – not following operating instructions (including failure to heed warnings) or use with equipment with which it is not intended to be used.
The warranty does not apply to any consequential damages.
Warranty is not applicable for supplementary product equipment i. e. PSU, power cables, antennas) unless the accessory is defective on arrival.
More information on what is RMA1
wiki.teltonika-gps.com/view/RMA_guidelines

FAQS

Q: How can I check the status of my device?
A: Use the various status window tabs to display information about GNSS, GSM, I/O, Maintenance, and more. You can also save configurations to the device for future use.

Documents / Resources

TELTONIKA FMM920 Tracker Smart and Small [pdf] User Guide
FMM920 Tracker Smart and Small, FMM920, Tracker Smart and Small, Smart and Small

References

User Manual

TELTONIKA FMM920 Tracker Smart and Small

Specifications

Product Information