TELESIN T10 Remote Controller User Guide
Overview
LCD Display
Button
Shutter/Select Button
1s Short Press
Shoot photo, turn on/off recording
3s Long Press Enter phone pairing mode, only photo function in phone mode, Bluetooth name is ‘T-10″
Star Button
When in the three main modes ‘Video”, `Photo”, “Time-lapse” Set the current main mode to ‘Quick mode’ Enter the main mode ear responding to the “Quick mode
Mode Button [Power/Mode Switching
2s Long press
Power On
3s long press
Power Off
1s Short press
Mode Switching
(After pairing. you can control the camera on and of)
Setting Button (Pairing, small mode switching)
1s short press
The camera switches between the normal sub-modes of the main mode.
(The sub-modes of different camera models are different and cannot be standardized)
Pairing
Setting Button
3s Long Press
The remote control enters pairing mode, and the Bluetooth indicator flashes
Camera Setting
Select connections > Connected Device > Remote control put the Camera into Pairing mode wait for a successful pairing message to appear on the camera screen
If the pairing fails, select Reset Connection in the camera setting and repeat the process.
If the camera has already been paired,you don’t need to pair it again when you connect the remote control next time, just make sure the wireless Connection of the camera has been turned on, and it will be connected automatically after a few moments. When the camera Es not used fora long time, the wit connection may be turned off completely so please unplug the camera battery and plug It back In to activate the wireless connection.
Pair Up 5
- Camera mode
In the state of the first camera connected, long press the pairing button 3 seconds remote control Bluetooth Indicator flashing you can connect the second camera and so on, the maximum number of connected 5. - Status Display
The display status of the first camera connected - Power On/OFF
- All the connected camera can be controlled at the same time to (Shutdown)
- Only the first connected camera can remain connected in the shutdown state
- The first connected camera can be controlled to (Power on)
- Connecting the next four camera requires the previous steps to be performed again.
Charging
Plug the charging cable into the charging slot. connect the other and of the cable a computer or other USB power source.
Charging Time 2.5h
Usage Time 10h
Please keep the charging device away from metal object to prevent fire caused by short circuit.
When Charging the screen lights up and the power indicator starts to work
| 0-5 | Side Blinking | Side Always On |
| 5-24 | Side Always On | |
| 25-49 | 1/3 Power | 1/3 Power |
| 50-74 | 2/3 Power | 2/3 Power |
| 75-100 | Full Power | Full Power |
Documents / Resources
 | T10 Remote Controller |
References
- 2.sh - This is a premium name2.sh
- r.mer.me
- User Manualmanual.tools
how do you reset the TELESIN T10 Remote Controller.. I have “CHG” in the LCD and it won’t turn off
How do I reset the TELESIN T10 Remote Controller if it is stuck on the 'CHG' screen and won't turn off?
The TELESIN T10 Remote Controller manual does not list a dedicated physical reset button. If your device is stuck displaying "CHG" (Charging) and will not respond to the power button, please try the following troubleshooting steps:
If the issue persists after the battery has been fully drained and recharged, there may be a hardware fault with the internal charging circuit.
Read the full Q&A page
I have purchased two of these units from Amazon and both are/were a piece of garbage. First won’t charge and light up. Second… won’t turn off. Always shows “CHG’ and stays lighted after you turn it off . There is no trouble shoot and instructions suck big time. I’m truly believe customer ratings are fake. Will send them back but I don’t get a remote…. Garbage
How do I troubleshoot a TELESIN T10 remote that won't charge or won't turn off and stays on 'CHG'?
Based on the TELESIN T10 Remote Controller User Guide, here is the information regarding charging and power states:
If one unit will not light up at all even when connected to power for 2.5 hours, and the other remains stuck on the "CHG" screen despite long-pressing the power button, these may be hardware defects. Since the manual does not provide a specific "reset" button combination, and you have already experienced failures with two units, returning them to the retailer as you planned is the recommended course of action.
Read the full Q&A page
Wie kann man das Gerät zurücksetzen wieder auf die Grundeinstellung.
Frage zwei: kann man ein iPhone 16 mit diesem Gerät verbinden. Über eine Antwort würde ich mich freuen. Gruß Ludwig Veith
Frage zwei: kann man ein iPhone 16 mit diesem Gerät verbinden. Über eine Antwort würde ich mich freuen. Gruß Ludwig Veith
How do I reset the TELESIN T10 remote to factory settings and is it compatible with iPhone 16?
Based on the TELESIN T10 Remote Controller User Guide, here is the information regarding your questions:
If the device is unresponsive, ensure it is fully charged using the included magnetic charging cable; the screen will light up and the power indicator will show the charging status.
Read the full Q&A page