TECH Sinum C-S1m Sensor
Product Description
The C-S1m sensor is a device that measures the temperature and humidity in the room.
Additionally, a floor sensor can be connected to the device 4 . Sensor measurements are displayed in the Sinum Central device. Each parameter can be used to create automations or assigned to a scene. C-S1m is surface-mounted and communicates with the Sinum Central device via cable.
Sensor connection
The system has a terminating connection. The position of the sensor on the transmission line with the Sinum Central is determined by the position of the terminating switch 3 .
Set to ON position (sensor at the end of the line) or position 1 (sensor in the middle of the line).
How to register the device in the sinum system
The device should be connected to the Sinum central device using the SBUS connector 2 and then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > SBUS devices > + > Add device. Then briefly press the registration button 1 on the device.
After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.
How to identify the device in the Sinum system
To identify the device in the Sinum Central, activate the Identification Mode in the Settings > Devices > SBUS Devices > + > Identification Mode tab and hold the registration button on the device for 3-4 seconds. The device used will be highlighted on the screen.
Technical data
| Power supply | 24V DC ±10% |
| Max. power consumption | 0,2W |
| Temperature measurement range | -30 ÷ 50ºC |
Notes
TECH Controllers is not responsible for any damages resulting from improper use of the system. The manufacturer reserves the right to improve devices, update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website.
Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children.
It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant.
The product may not be disposed of to household waste containers.
The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.
EU Declaration of conformity
Tech Sterowniki II Sp. z o.o. , ul. Biała Droga 34, Wieprz (34-122) Hereby, we declare under our sole responsibility that the C-S1m sensor is compliant with Directive :
- 2014/35/UE
- 2014/30/UE
- 2009/125/WE
- 2017/2102/UE
For compliance assessment, harmonized standards were used:
- PN-EN IEC 60730-2-9:2019-06
- PN-EN 60730-1:2016-10
- PN-EN IEC 60730-2-13:2018-11
- PN-EN IEC 62368-1:2020-11
- EN IEC 63000:2019-01 RoHS
Wieprz, 01.12.2023
The full text of the EU declaration of conformity and the user manual are available after
scanning the QR code or at www.tech-controllers.com/manuals
www.tech-controllers.com/manuals
Made in Poland
TECH STEROWNIKI II Sp. z o.o.
ul. Biała Droga 31
34-122 Wieprz
Customer Support
tel: +48 33 875 93 80 www.tech-controllers.com support.sinum@techsterowniki.pl
Documents / Resources
 |
TECH Sinum C-S1m Sensor [pdf] User Manual C-S1m, Sinum C-S1m Sensor, Sinum C-S1m, Sensor |
