TECH Controllers CP-04 Sinum control panel Instructions

TECH Controllers CP-04 Sinum control panel

Technical Data & Specifications

The CP-04 control panel is a device equipped with a 4-inch touch screen. After configuring the device in the Sinum Central, you can adjust the temperature in the mm directly from the panel, display the weather forecast on the screens and create shortcuts of your favorite scenes. CP-04 is flush mounted in 060mm electrical 1m. Communication with the Sinum Central device is done by wire.

Important!
The mm sensor should be mounted below or next to the control panel at a distance of at
least 10 cm. The sensor should not be mounted in a sunny location.

Menu Function

1. Registration – registration a device in the Sinum central device.
2. Room sensor – temgHature calibration of the built-in sensor
3. Floor sensor – on/off floor sensor; sensor temperature
4. Device identification – allows you to læate a specific device in the tab Settings > Devices > SBUS devices>@> Identyfication mode in the Sinum Central device settings.
5. Screen settings – settings of screen parameters such as: brightness, dimming, theme change, on/off button sound
6. Return to the home screen – on/off automatic return to the home screen; setting the delay time to return to the home screen
7. Automatic lock – on/off automatic lock, setting the delay time automatic lock; PIN code setting
8. Language version – changing the menu language
9. Software version – preview of the softvare version
10. Software update via IJSB – from the memory stick connected to the micro  USB port on the device
11. Factory settings – restoring factory settings

Description

1. Floor sensor connector
2. Room sensor connector
3. SBUS communication connector
4. Micro USB

How to register the device in the sinum system
The device should be connected to the Sinum central device using the SBUS connector and then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > SBUS devices > > Add device. Next, click Registration in CP-04 menu. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.

Notes

• TECH Controllers is not responsible for any damages resulting from improper use of the system. The manufacturer reserves the right to improve devices, update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website.
• Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children.
• It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant.
• The product may not be disposed of to household waste containers.
• The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.

Instructions

EU Declaration of conformity

Tech Sterowniki II Sp. z 0.0. , Ill. Biala Droga 34, Wieprz (34-122) Hereby, we declare under our sole responsibility that the control panel CP-04 is compliant with Directive :

• 2014/35/1—1 E
• 2014/30/UE
• 2009/125/WE
• 2017/2102/UE

For compliance assessment, harmonized standards were used:

• PN-EN IEC 60730-2-9:2019-06
• PN-EN 60730-1:2016-10
• PN-EN IEC 62368-1:2020-11
• EN IEC 630002018 RoHS

Wieprz, 01.10.2025

The full text of the EU declaration of conformity and the user manual are available after scanning the QR code or at www.tech-controllers.com/manuals

• www.tech-controllers.com/manuals
• Made in Poland