VB Series General Purpose RFI Filters
Specifications:
- Product Name: B Series RFI Power Line Filters
- Application: General Purpose RFI Filters for High Impedance
Loads at Low Current - Certifications: UL Recognized, CSA Certified, VDE Approved
Product Usage Instructions:
1. Application:
The B Series RFI Power Line Filters are designed for use with
portable equipment and non-patient medical equipment.
2. Installation:
Ensure that the power source is disconnected before installing
the filter. Connect the filter in-line with the power supply cable
of the equipment, following the manufacturer’s guidelines.
3. Maintenance:
Regularly inspect the filter for any signs of damage or wear.
Replace the filter if any issues are detected to maintain optimal
performance.
4. Troubleshooting:
If you experience any interference or noise issues with your
equipment, check the filter connections and ensure they are secure.
Contact customer support if problems persist.
FAQ:
Q: Can the B Series RFI Power Line Filters be used with
high-power equipment?
A: The filters are designed for high impedance loads at low
current. It is recommended to check the product specifications and
consult with the manufacturer for compatibility with high-power
equipment.
Q: How do I know if the filter needs replacement?
A: If you notice a decrease in filter performance, such as
increased interference or noise, or physical damage to the filter,
it may be time for a replacement. Regular maintenance checks are
advised to ensure optimal functionality.
B Series
Corcom Product Guide
Catalog: 1654001 Issue Date: 06.2011
General Purpose RFI Filters for High Impedance Loads at Low Current
UL Recognized CSA Certified VDE Approved
VB6
1
RFI Power Line Filters
B Series
· Small size & low cost · General purpose · Wide variety of termination options · Meets low leakage current requirements of VDE
portable equipment and non-patient medical equipment
Ordering Information 10 E B 1
Input / Output Style 1 .250 [6.3] spade terminals 3 Wire leads 6 Threaded bolt
B Series
Leakage current designation E Low leakage (<0.5 mA) V Standard
Current Rating 1, 2, 3, 5, 10, 20 or 30A
Electrical Schematic
LINE
LOAD
VB1 / EB1
VB3 / EB3
Specifications
Maximum leakage current each Line to Ground:
VB Models
EB Models
@ 120 VAC 60 Hz:
.4 mA
.21 mA
@250 VAC 50 Hz:
.7 mA
.36 mA
Hipot rating (one minute): Line to Ground: Line to Line:
2250 VDC 1450 VDC
Rated Voltage (max): Operating Frequency: Rated Current:
250 VAC 50/60 Hz
1 to 30A
Operating Ambient Temperature Range
(at rated current Ir):
-10°C to +40°C
In an ambient temperature (Ta) higher than +40°C
the maximum operating current (Io) is calculated as
follows: Io = Ir (85-Ta)/45
Available Part Numbers
1VB1 1VB3 2VB1 2VB3 3VB1 3VB3 5VB1 5VB3 10VB1 10VB3 10VB6 20VB1 20VB6 30VB6
1EB1 1EB3 2EB1 2EB3 3EB1 3EB3 5EB1 5EB3 10EB1 10EB3 20EB1
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.
Downloaded from Arrow.com.
15
For email, phone or live chat, please go to
te.com/help
corcom.com
B Series
Case Styles B1
Corcom Product Guide
Catalog: 1654001 Issue Date: 06.2011
General Purpose RFI Filters for High Impedance/ Low Current (continued)
30VB6
E DB
A
C
E DB
2.00 50.8
A
C
B3
Blue
E DB
Brown
Blue Green/Yellow
Brown
A
C
10VB6 & 20VB6
E DB
A
C
Case Dimensions
Part No.
A
B
1VB1, 1EB1, 2VB1, 2EB1
1VB3, 1EB3,
2VB3, 2EB3
3VB1, 3EB1,
5VB1, 5EB1
3VB3, 3EB3, 5VB3, 5EB3
10VB1, 10EB1
10VB3, 10EB3
10VB6
20VB1, 20EB1
20VB6
30VB6
C
D
E
16
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.
Downloaded from Arrow.com.
For email, phone or live chat, please go to te.com/help corcom.com
Corcom Product Guide
Catalog: 1654001 Issue Date: 06.2011
General Purpose RFI Filters for High Impedance/ Low Current (continued)
B Series
Performance Data
Typical Insertion Loss
Measured in closed 50 Ohm system
1EB & 3EB
db 100 90 80 70 60 50 40 30 20
10
0
0.1
1
10
30
Frequency in MHz
Common Mode / Asymmetrical (L-G) Differential Mode / Symmetrical (L-L)
2EB, 5EB & 10EB
db 100 90 80 70 60 50 40 30
20 10 0
0.1
1
10
30
Frequency in MHz
20EB
db 100
90
80
70
60
50
40
30
20
10
0
0.1
1
10
30
Frequency in MHz
1VB
db 100 90 80 70 60 50 40 30 20
10 0
0.1
1
10
30
Frequency in MHz
2VB
db 100 90 80 70 60 50 40 30 20
10 0
0.1
1
10
30
Frequency in MHz
3VB
db 100 90 80 70 60 50 40 30 20
10 0
0.1
1
10
30
Frequency in MHz
10VB
db 100
90
80
70
60
50
40
30
20
10
0
0.1
1
10
30
Frequency in MHz
20VB
db 100
90
80
70
60
50
40
30
20
10
0
0.1
1
Minimum Insertion Loss
Measured in closed 50 Ohm system
Common Mode / Asymmetrical (Line to Ground)
10
30
Frequency in MHz
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.
Downloaded from Arrow.com.
30VB
db 100
90
80
70
60
50
40
30
20
10
0
0.1
1
10
30
Frequency in MHz
17
For email, phone or live chat, please go to
te.com/help
corcom.com
RFI Power Line Filters
1
Documents / Resources
 |
TE connectivity VB Series General Purpose RFI Filters [pdf] User Guide VB6, VB Series General Purpose RFI Filters, VB Series, General Purpose RFI Filters, Purpose RFI Filters, RFI Filters, Filters |