TE Connectivity SRBP Series Corcom Shielded Power Inlet Filter
Specifications
- UL Recognized, CSA Certified, VDE Approved
- Operating Frequency: 50/60 Hz
- Rated Voltage: 250 VAC
- Rated Current: 15A
- Capacitor Options: Q, R, S, T, W, X, Y, Z
- Hipot Rating: 2250 VDC Line to Ground, 1450 VDC Line to Line
Product Usage Instructions
Installation
- Ensure power is disconnected before installation.
- Mount the SRB Series filter securely in the desired location.
- Connect the input power lines to the designated terminals following proper polarity.
- Ground the filter according to local electrical codes.
Maintenance
Regularly inspect the filter for any signs of damage or wear. Replace if necessary to maintain optimal performance.
SRB Series
- Smallest depth Corcom RFI filter available
- Complete shield
- Wide range of capacitor values
- Attenuates coupled EMI up to 300MHz
- Minimal to low leakage current versions are suitable for patient and non-patient contact medical equipment.
- Full range of mounting and termination options including unique vertical and horizontal orientation slide in mounts, eliminates the need for mounting hardware
Ordering Information
- 15A versions are tested by Underwriters Laboratories to US and Canadian requirements and are VDE approved at 10A, 250VAC
Specifications
Maximum leakage current each Line to Ground
Hipot rating (one minute)
- Line to Ground: 2250 VDC
- Line to Line: 1450 VDC
- Rated Voltage (max.): 250 VAC
- Operating Frequency: 50/60 Hz
- Rated Current: 15A*
Operating Ambient Temperature Range (at rated current Ir)
Capacitor Options
| Capacitor ID | Capacitor Value |
| Q | 33 pF |
| R | 100 pF |
| S | 220 pF |
| T | 330 pF |
| W | 470 pF |
| X | 1000 pF |
| Y* | 2200 pF |
| Z* | 3300 pF |
Available Part Numbers
Flange Mount
| 15SRB1 | 15SRB2 | 15SRBP | 15SRB8 |
| 15SRB1-Q | 15SRB2-Q | 15SRBP-Q | 15SRB8-Q |
| 15SRB1-R | 15SRB2-R | 15SRBP-R | 15SRB8-R |
| 15SRB1-S | 15SRB2-S | 15SRBP-S | 15SRB8-S |
| 15SRB1-T | 15SRB2-T | 15SRBP-T | 15SRB8-T |
| 15SRB1-W | 15SRB2-W | 15SRBP-W | 15SRB8-W |
| 15SRB1-X | 15SRB2-X | 15SRBP-X | 15SRB8-X |
| 15SRB1-Y | 15SRB2-Y | 15SRBP-Y | |
| 15SRB1-Z | 15SRB2-Z | 15SRBP-Z | |
| Snap-In | Slide-In | ||
| 15SRBS1 | 15SRBS8 | 15SRBX8 | 15SRBY8 |
| 15SRBS1-Q | 15SRBS8-Q | 15SRBX8-Q | 15SRBY8-Q |
| 15SRBS1-R | 15SRBS8-R | 15SRBX8-R | 15SRBY8-R |
| 15SRBS1-S | 15SRBS8-S | 15SRBX8-S | 15SRBY8-S |
| 15SRBS1-T | 15SRBS8-T | 15SRBX8-T | 15SRBY8-T |
| 15SRBS1-W | 15SRBS8-W | 15SRBX8-W | 15SRBY8-W |
| 15SRBS1-X | 15SRBS8-X | 15SRBX8-X | 15SRBY8-X |
| 15SRBS1-Y | |||
| 15SRBS1-Z | |||
Electrical Schematic
Accessories
- GA400: NEMA 5-15P to IEC 60320-1 C-13 line cord
Case Styles
SRB1
Typical Dimensions:
- Mounting holes (2):
- 132 [3.35] Dia. with .236 [5.99] Dia. x 90° countersink for #4 flathead screw
- Line Inlet (1):
- IEC 60320-1 C14
- Load Terminals (2):
- 250 [6.3) with .07 [1.8] Dia. hole
- Ground Terminal (1):
- 250 [6.3] with .07 x .16 [1.8 x 3.8] slot
SRB2
Typical Dimensions
- Mounting holes (2):
- 132 [3.35] Dia. with .236 [5.99] Dia. x 90° countersink for #4 flathead screw
- Line Inlet (1):
- IEC 60320-1 C14
- Load Terminals (2):
- 250 [6.3] with .07 [1.8] Dia. hole
- Ground Terminal (1):
- 250 [6.3] with .07 x .16 [1.8 x 3.8] slot
SRBP
- Mounting holes (2)
- IEC 60320-1 C14
- Line Inlet (1)
- 250 [6.3] with .07 [1.8] Dia. hole
- PC board pins (3)
- 250 [6.3] with .07 x .16 [1.8 x 3.8] slot
SRB8
Typical Dimensions
- Mounting holes (2): 132 [3.35] Dia. with .236 [5.99] Dia. x 90° countersink for #4 flathead screw
- Line Inlet (1): IEC 60320-1 C14
- Wire Leads: 4.0 [101.6] Min., 18AWG, UL1015
SRBS8
Typical Dimensions
- Line Inlet (1):
- IEC 60320-1 C14
- Wire Leads:
- 4.0 [101.6] Min., 18AWG, UL1015
SRBY8
Typical Dimensions
- Line Inlet (1):
- IEC 60320-1 C14
- Wire Leads:
- 4.0 [101.6] Min., 18AWG, UL1015
Case Dimensions
Recommended Panel Cutouts
SRB1, SRB2, SRBP & SRB8
SRBS
SRBX
SRBY
PC Board Layout
Performance Data
Typical Insertion Loss
Measured in a closed 50 Ohm system
Minimum Insertion Loss
Common Mode / Asymmetrical (Line to Ground)
Measured in closed 50 Ohm system
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.For email, phone or live chat, please go to te.com/help corcom.com
FAQs
What is the maximum leakage current for each Line to Ground at different voltages?
@120 VAC: 2.1 A, @250 VAC: 3.65 A
What are the available capacitor options for the SRB Series?
Q (33 pF), R (100 pF), S (220 pF), T (330 pF), W (470 pF), X (1000 pF), Y (2200 pF), Z (3300 pF)
How should I calculate the maximum operating current for the SRB Series?
Io = Ir (85-Ta)/45, where Io is the maximum operating current, Ir is the rated current, and Ta is the ambient temperature.
Documents / Resources
 |
TE Connectivity SRBP Series Corcom Shielded Power Inlet Filter [pdf] User Guide SRBP, SRBS8, SRB1, SRB2, SRBP Series Corcom Shielded Power Inlet Filter, SRBP Series, Corcom Shielded Power Inlet Filter, Shielded Power Inlet Filter, Power Inlet Filter, Inlet Filter, Filter |