TE Connectivity 2MM-RD-S12-S-T-TB Amp Modu 2 Mm Interconnection System
Specifications
- Materials: Housing – Liquid Crystal Polymer, UL 94V0, Black; Contact – Phosphor Bronze
- Contact Plating: Not specified
- Electrical:
- Voltage Rating: 125 Vrms (max.)
- Current Rating: 2 A (max.)
- Operating Temperature: Not specified
- Dielectric Withstanding Voltage: 650 VAC
- Mechanical:
- Durability: 25 cycles
- Connector Mating/Unmating Force: Mating: 2.2 N max., Unmating: 0.2 N min.
- Contact Retention Force in Housing (Board Connectors): 5 N min.
- Contact Retention Force in Housing (Wire Receptacles): 10 N min.
- Vibration: No electrical discontinuity greater than 1 microsecond under specified conditions
- Shock Latch Durability: No electrical discontinuity greater than 1 microsecond by 50 G acceleration
- Positive Latch Engage/Disengage Force (without Contacts): Engage: 6 N max., Disengage: 20 N min.
Product Usage Instructions
Configurations:
The AMPMODU 2 mm interconnection system offers various configurations for headers and receptacles including breakaway, shrouded with detent latches, shrouded with positive latch, board receptacles, crimp snap-in receptacles, and insulation displacement contacts (IDC) receptacles. Choose the appropriate configuration based on your application needs.
Installation:
- Ensure proper alignment of the connectors before mating. Apply gentle pressure to securely connect the headers and receptacles.
- Verify that the connectors are fully engaged to prevent signal loss or damage.
Maintenance:
- Regularly inspect the connectors for any signs of damage or wear. Clean the contacts if necessary using a soft, dry cloth.
- Avoid using abrasive materials that may scratch the contacts.
FAQ
- Q: What are the certifications and approvals for the AMPMODU 2 mm interconnection system?
- A: The product is certified with RoHS, REACH, and cURus approvals. Specific product specifications are provided for headers, board receptacles, crimp snap-in receptacles, and IDC receptacles.
- Q: What is the voltage and current rating of the system?
- A: The system has a voltage rating of 125 Vrms (max) and a current rating of 2 A (max).
- Q: How do I choose the right configuration for my application?
- A: Consider factors such as space constraints, mating/unmating force requirements, and environmental conditions when selecting the configuration. Refer to the product manual for detailed information on each configuration.
INTRODUCTION
TE Connectivity (TE)’s AMPMODU 2 mm interconnection system reliably and economically meets the requirements of today’s miniature, sophisticated electronics. This system is ideal for space constrained environments and offers a wide portfolio with design features that enable reliable signal transfers in demanding applications.
TE’s compact 2 mm design enables space savings, providing designers with greater overall flexibility. The AMPMODU 2 mm system occupies 38% less space on a printed circuit board as compared to traditional 2.54 mm centerline connectors. This connector system is available in both board-to-board and wire-to-board mating options and utilizes a dual-beam contact design to enable 2 points of contact for increased signal reliability. The AMPMODU 2 mm connection system is available in 4 types of plating options: 30µ” [0.76 µm] gold, 15µ” [0.38 µm] gold, 4µ” [0.1 µm] gold flash, and tin. All 2 mm board-mount connectors are offered in single and double row versions and vertical and horizontal orientations for both headers and receptacles. Surface mount and through-hole mounting options are available with the capability to support reflow solder processes up to 260°C.
Board-mount connectors can be packaged in tape and reel to support automated assembly processes, or in tubes, which may be ideal in manual assembly environments. AMPMODU 2 mm wire-to-board connectors are available without latches, and with detent or positive latches for high-vibrations applications that demand more secure electrical connections. Wire-mount receptacles are offered with two options for discrete wire termination crimp snap-in contacts and insulation displacement contacts (IDC). Additionally, wire termination is easily accomplished with TE-designed application tooling.
The AMPMODU 2 mm interconnection system is the clear choice for demanding Industrial applications, offering a comprehensive, economical, and reliable connector portfolio.
FEATURES
· Centerline: 0.079″ [2 mm] · 0.020″ [0.50 mm] square pins for headers · Dual-beam receptacle contact · Multiple solder tail lengths for various PCB
thicknesses, 0.063″ to 0.094″ [1.6 mm to 2.4 mm] · High temperature plastic (LCP) housing · Board connectors available in tube and tape & reel
packaging · Up to 25 positions per row, single and dual row
offering · Wire termination: crimp and IDC · Wire size:
· Crimp contacts: AWG 30 – 24 · IDC: AWG 30 26 · Environmental: UL94V0, low halogen
APPLICATIONS
· PLC · I/O devices · Servo drives · Robotics · Automated guided vehicles · Material handling equipment · Industrial controls · Instrumentation and test equipment · Building automation devices · Medical equipment · Energy storage systems
BENEFITS
· Occupies 38% less space on PCB board compared with 0.100″ [2.54 mm] centerline
· Two-point electrical stability for reliable signal transfer · Multiple options for Board-to-Board stacking by various
header and receptacle combinations · Ease of assembly with automated surface-mounting
and through-hole reflow manufacturing · Reliable connection in high vibration environments with
detent and positive latching variants · Ergonomic and easy mating/unmating process with
positive latching variant · Headers are intermateable with other major brand
receptacles · Design flexibility with various crimp terminal options · Fast termination/installation without the need to strip
the wire with IDC wire receptacles · IDC and crimp receptacles mate with the same headers · Interchangeable IDC and Crimp Snap-In contacts allow
for easy replacement of damaged/faulty contacts
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
AMPMODU 2 MM INTERCONNECTION SYSTEM
OVERVIEW
5 4
4
2
3
1
1
5
5
3
5
4
1
4 1
2
5
4
2
2
1 4
1
BREAKAWAY HEADERS
2
SHROUDED HEADERS
SHROUDED HEADERS W/ DETENT LATCHES
3
SHROUDED HEADERS W/ POSITIVE LATCH
4
BOARD RECEPTACLES
CRIMP SNAP-IN RECEPTACLES 5
INSULATION DISPLACEMENT CONTACTS (IDC) RECEPTACLES
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM Downloaded from Arrow.com.
Page 9 – 12 Page 13 – 16 Page 17 – 20 Page 21 – 25 Page 26 – 29 Page 30 – 33
3
AMPMODU 2 MM INTERCONNECTION SYSTEM
AMPMODU 2 MM INTERCONNECTION SYSTEM PERFORMANCE SPECIFICATIONS AND STANDARDS
MATERIALS Housing Contact
Contact Plating
Liquid Crystal Polymer, UL 94V0, Black Phosphor Bronze
30µ” [0.76 µm] Gold 15µ” [0.38 µm] Gold
4µ” [0.1 µm] Gold Tin
ELECTRICAL
Voltage Rating Current Rating Operating Temperature Dielectric Withstanding Voltage Temperature Rise
125 Vrms (max.) 2 A (max.)
Tin Plating: -40 to +105°C Gold Plating: -40 to +125°C
650 VAC
30°C@1.6A
SPECIFICATIONS AND APPROVALS
Certifications and Approvals
Product Specification
Application Specification
RoHS REACH cURus Headers: 108-64040 Board Receptacles: 108-64040 Crimp Snap-In Receptacles: 108-64040-1 IDC Receptacles: 108-64040-2 Headers: 114-64040 Board Receptacles: 114-32186 Crimp Snap-In Receptacles: 114-32173 IDC Receptacles: 114-32175
MECHANICAL
Durability
30µ” [0.76 µm] Gold: 250 cycles 15µ” [0.38 µm] Gold: 100 cycles
4µ” [0.1 µm]Gold: 50 cycles Tin: 25 cycles
Connector Mating/ Unmating Force
Mating: 2.2 N max. Unmating: 0.2 N min.
Contact Retention Force in Housing (Board Connectors) Contact Retention Force in Housing (Wire Receptacles)
Vibration
Shock Latch Durability
5 N min.
10 N min.
No electrical discontinuity greater than 1 microsecond under 10-55-10 Hz traversed in minute at 1.52 mm amplitude No electrical discontinuity greater than 1 microsecond by 50 G acceleration
25 cycles
Positive Latch Engage/Disengage Force (without Contacts)
Engage: 6 N max. Disengage: 20 N min.
Solderability
Reflow Solderable, Capable up to 260°C
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
4
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
CONFIGURATIONS
Headers
A
BREAKAWAY VERTICAL
B
BREAKAWAY VERTICAL
C
TH
SMT
BREAKAWAY HORIZONTAL
TH
Receptacles
1
BOARD VERTICAL
2
BOARD VERTICAL
3
BOARD HORIZONTAL
4
BOARD HORIZONTAL
TH
SMT
TH
SMT
D
SHROUDED W/ DETENT
LATCHES VERTICAL
TH
E
SHROUDED W/ DETENT
LATCHES VERTICAL
SMT
F
SHROUDED W/ DETENT
LATCHES HORIONTAL
TH
BOARD VERTICAL OUTRIGGER
TH
G
SHROUDED W/ POSITIVE
H
SHROUDED W/ POSITIVE
J
SHROUDED W/ POSITIVE
LATCH VERTICAL
LATCH VERTICAL LATCH HORIZONTAL
TH
SMT
TH
5
WIRE (CRIMP/IDC)
6
WIRE (CRIMP/IDC)
7
WIRE (CRIMP/IDC)
STANDARD
W/ DETENT W/ POSITIVE LATCH
LATCHES
BOARD-TO-BOARD
Application
Parallel boards – vertical board receptacle and vertical shrouded
header
A1 B1 A2 B2
X (Single Row) 0.083″ [2.10 mm] 0.083″ [2.10 mm] 0.083″ [2.10 mm] 0.083″ [2.10 mm]
X (Double Row) 0.161″ [4.10 mm] 0.161″ [4.10 mm] 0.161″ [4.10 mm] 0.161″ [4.10 mm]
Y 0.236″ [6.00 mm] 0.285″ [7.25 mm] 0.244″ [6.20 mm] 0.293″ [7.45 mm]
Application
Parallel boards – vertical board receptacle and vertical shrouded
header
D1 E1 D2 E2
X (Single Row) 0.157″ [4.00 mm] 0.157″ [4.00 mm] 0.157″ [4.00 mm] 0.157″ [4.00 mm]
X (Double Row) 0.244″ [6.20 mm] 0.244″ [6.20 mm] 0.244″ [6.20 mm] 0.244″ [6.20 mm]
Y 0.236″ [6.00 mm] 0.285″ [7.25 mm] 0.244″ [6.20 mm] 0.293″ [7.45 mm]
Application
Perpendicular boards vertical board receptacle
and horizontal breakaway header
C1 C2
X (Single Row) 0.083″ [2.10 mm] 0.083″ [2.10 mm]
X (Double Row) 0.161″ [4.10 mm] 0.161″ [4.10 mm]
Y 0.236″ [6.00 mm] 0.244″ [6.20 mm]
Application
X (Single Row) X (Double Row)
Y
Perpendicular boards vertical board receptacle and horizontal shrouded
header
F1 F2
0.157″ [4.00 mm] 0.157″ [4.00 mm]
0.244″ [6.20 mm] 0.244″ [6.20 mm]
0.236″ [6.00 mm] 0.244″ [6.20 mm]
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
5
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
CONFIGURATIONS – CONTINUED
BOARD-TO-BOARD
Application
Perpendicular boards – horizontal board
receptacle and vertical breakaway header
A3 B3 A4 B 4
X (Single Row) 0.083″ [2.10 mm] 0.083″ [2.10 mm] 0.093″ [2.35 mm] 0.093″ [2.35 mm]
X (Double Row) 0.161″ [4.10 mm] 0.161″ [4.10 mm] 0.172″ [4.36 mm] 0.172″ [4.36 mm]
Y 0.244″ [6.20 mm] 0.293″ [7.45 mm] 0.244″ [6.20 mm] 0.293″ [7.45 mm]
WIRE-TO-BOARD
Application
Perpendicular to PCB nonlatching solution – breakaway header and standard wire receptacle (no
latches)
Row
A5
Single row Double row
B5
Single row Double row
Crimp
X
Y
0.099″ [2.51 mm] 0.185″ [4.70 mm] 0.099″ [2.51 mm] 0.185″ [4.70 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm] 0.443″ [11.25 mm] 0.443″ [11.25 mm]
IDC
X
Y
0.094″ [2.4 mm]
–
0.094″ [2.4 mm]
–
0.57″ [14.50 mm]
–
0.62″ [15.75 mm]
–
Application
Parallel to PCB – non-latching
solution breakaway header and standard wire
receptacle (no latches)
C5
Row
Single row Double row
Crimp
X
Y
0.099″ [2.51 mm] 0.185″ [4.70 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm]
IDC
X
Y
0.094″ [2.4 mm] –
0.57″ [14.50 mm] –
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
6
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
CONFIGURATIONS – CONTINUED
WIRE-TO-BOARD
Application
Perpendicular to PCB – non-latching solution
– shrouded header with detent latches and standard wire receptacle (no latches)
Row
D5
Single row Double row
E5
Single row Double row
Crimp
X
Y
0.157″ [4.00 mm] 0.244″ [6.20 mm] 0.157″ [4.00 mm] 0.244″ [6.20 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm] 0.443″ [11.25 mm] 0.443″ [11.25 mm]
IDC
X
Y
0.157″ [4.00 mm]
–
0.157″ [4.00 mm]
–
0.57″ [14.50 mm]
–
0.62″ [15.75 mm]
–
Application
Perpendicular to PCB – detent latching solutions – shrouded header with detent latches and wire receptacle with detent latches
Row
D6
Single row
Double row
E6
Single row
Double row
Crimp
X
Y
0.157″ [4.00 mm] 0.244″ [6.20 mm] 0.157″ [4.00 mm] 0.244″ [6.20 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm] 0.443″ [11.25 mm] 0.443″ [11.25 mm]
IDC
X
Y
0.157″ [4.00 mm]
–
0.157″ [4.00 mm]
–
.57″ [14.50 mm]
–
0.62″ [15.75 mm]
–
Application
Parallel to PCB non-latching solution
– shrouded header with detent latches and standard wire receptacle (no latches)
Row
F5
Single row Double row
Crimp
X
Y
0.157″ [4.00 mm] 0.244″ [6.20 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm]
IDC
X
Y
0.157″ [4.00 mm]
0.57″ [14.50 mm]
–
–
Application
Parallel to PCB – detent latching solution –
shrouded header with detent latches and wire receptacle with detent
latches
Row
F6
Single row Double row
Crimp
X
Y
0.157″ [4.00 mm] 0.244″ [6.20 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm]
IDC
X
Y
0.157″ [4.00 mm]
0.57″ [14.50 mm]
–
–
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
7
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
CONFIGURATIONS – CONTINUED
WIRE-TO-BOARD
Application
Perpendicular to PCB positive latching solution – shrouded
header with positive latch wire and wire receptacle with positive
latch
Row
G7
Single row Double row
H7
Single row Double row
Crimp
X
Y
0.218″ [5.54 mm] 0.305″ [7.74 mm] 0.218″ [5.54 mm] 0.305″ [7.74 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm] 0.443″ [11.25 mm] 0.443″ [11.25 mm]
IDC
X
Y
0.218″ [5.54 mm]
–
0.218″ [5.54 mm]
–
0.57″ [14.50 mm]
–
0.62″ [15.75 mm]
–
Application
Parallel to PCB positive latching solution – shrouded header with positive
latch and wire receptacle with positive
latch
Row
J7
Single row Double row
Crimp
X
Y
0.218″ [5.54 mm] 0.305″ [7.74 mm]
0.394″ [10.00 mm] 0.394″ [10.00 mm]
IDC
X
Y
0.218″ [5.54 mm] –
0.57″ [14.50 mm] –
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
8
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
BREAKAWAY HEADERS
SMART PART NUMBER DEFINITION
2MM – HB – _ _ – _ – _ – _ – _
PRODUCT SERIES
2MM AMPMODU 2 mm series
1
GENDER / TYPE
2
HB Breakaway headers
NUMBER OF ROWS
S Single row
3
D Double row
NUMBER OF PINS PER ROW
##
02 thru 25 per row (enter two digits)
4
PACKAGING
8
TB Tube without cap
Tube with cap TBP (N/A for 2 and 3 positions per row)
TRP Tape and reel with cap
*select allowable Packaging from table DESIGN NAVIGATOR
PLATING
T Tin
F 4µ” [0.1 µm] Gold (gold flash)
7
M 15µ” [0.38 µm] Gold
H 30µ” [0.76 µm] Gold
ORIENTATION & TERMINATION
VT Vertical through hole
5
VS Vertical surface mount
HT Horizontal through hole
TAIL LENGTH
6
00 N/A for surface mount
01 0.087″ [2.2 mm]
02 0.110″ [2.8 mm]
*see table DESIGN NAVIGATOR for guidance
*select allowable Tail Length from table
DESIGN NAVIGATOR
SMART PN EXAMPLES
· AMPMODU 2 mm, breakaway header, double row, 20 positions (2 x 10), vertical surface mount, tail length: N/A, tin, T&R with cap: 2MM-HB-D10-VS-00-T-TRP
DESIGN NAVIGATOR
Orientation & Termination
VT
Tail Length
Packaging
TB
01
0.087″ [2.2 mm]
TBP
TRP
TB
02
0.110″ [2.8 mm]
TBP
TRP
TRP
VS
00
–
TBP
TB
01
0.087″ [2.2 mm]
TBP
TRP HT
TB
02
0.110″ [2.8 mm]
TBP
TRP
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
9
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
BREAKAWAY HEADERS
SINGLE ROW
Product Type Vertical
Through Hole
Drawing Number
Solder Lead Length
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] 30µ” [0.76µm] Packaging
Gold
Gold
2823074
2823078
2823082
2823086
0.087″ [2.2mm]
2MM-HB-SXXVT-01-T-TB
2823651
2MM-HB-SXXVT-01-T-TBP
2MM-HB-SXXVT-01-F-TB
2823652
2MM-HB-SXXVT-01-F-TBP
2MM-HB-SXXVT-01-M-TB
2823653
2MM-HB-SXXVT-01-M-TBP
2MM-HB-SXXVT-01-H-TB
2823654
2MM-HB-SXXVT-01-H-TBP
Tube w/o cap
Tube w/ cap
Available Positions
2~25
3~25
2823465
2823466
2823467
2823468
2823074
0.110″ [2.8mm]
2MM-HB-SXXVT-01-T-TRP
2823076
2MM-HB-SXXVT-02-T-TB
2823655
2MM-HB-SXXVT-02-T-TBP
2MM-HB-SXXVT-01-F-TRP
2823080
2MM-HB-SXXVT-02-F-TB
2823656
2MM-HB-SXXVT-02-F-TBP
2MM-HB-SXXVT-01-M-TRP
2823084
2MM-HB-SXXVT-02-M-TB
2823657
2MM-HB-SXXVT-02-M-TBP
2MM-HB-SXXVT-01-H-TRP
2823088
2MM-HB-SXXVT-02-H-TB
2823658
2MM-HB-SXXVT-02-H-TBP
T&R w/ cap
Tube w/o cap
Tube w/ cap
2~25 2~25 3~25
Horizontal Through Hole
2823469
2823470
2823471
2823472
2MM-HB-SXX- 2MM-HB-SXX- 2MM-HB-SXX- 2MM-HB-SXXVT-02-T-TRP VT-02-F-TRP VT-02-M-TRP VT-02-H-TRP
T&R w/ cap
2823090
2823094
2823098
2823102
0.087″ [2.2mm]
2MM-HB-SXXHT-01-T-TB
2823671
2MM-HB-SXXHT-01-T-TBP
2MM-HB-SXXHT-01-F-TB
2823672
2MM-HB-SXXHT-01-F-TBP
2MM-HB-SXXHT-01-M-TB
2823673
2MM-HB-SXXHT-01-M-TBP
2MM-HB-SXXHT-01-H-TB
2823674
2MM-HB-SXXHT-01-H-TBP
Tube w/o cap
Tube w/ cap
2~25 2~25 3~25
2823481
2823482
2823483
2823484
Vertical Surface Mount
2823090 2823106
0.110″ [2.8mm] –
2MM-HB-SXXHT-01-T-TRP
2823092
2MM-HB-SXXHT-02-T-TB
2823683
2MM-HB-SXXHT-02-T-TBP
2823485
2MM-HB-SXXHT-02-T-TRP
2823106
2MM-HB-SXXVS-00-T-TRP
2823659
2MM-HB-SXXVS-00-T-TBP
2MM-HB-SXXHT-01-F-TRP
2823096
2MM-HB-SXXHT-02-F-TB
2823684
2MM-HB-SXXHT-02-F-TBP
2823486
2MM-HB-SXXHT-02-F-TRP
2823107
2MM-HB-SXXVS-00-F-TRP
2823660
2MM-HB-SXXVS-00-F-TBP
2MM-HB-SXXHT-01-M-TRP
2823100
2MM-HB-SXXHT-02-M-TB
2823685
2MM-HB-SXXHT-02-M-TBP
2823487
2MM-HB-SXXHT-02-M-TRP
2823108
2MM-HB-SXXVS-00-M-TRP
2823661
2MM-HB-SXXVS-00-M-TBP
2MM-HB-SXXHT-01-H-TRP
2823104
2MM-HB-SXXHT-02-H-TB
2823686
2MM-HB-SXXHT-02-H-TBP
2823488
2MM-HB-SXXHT-02-H-TRP
2823109
2MM-HB-SXXVS-00-H-TRP
2823662
2MM-HB-SXXVS-00-H-TBP
T&R w/ cap
Tube w/o cap
Tube w/ cap
T&R w/ cap
T&R w/ cap
Tube w/ cap
2~25 2~25 3~25 2~25 2~25 3~25
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
10
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
BREAKAWAY HEADERS
DOUBLE ROW
Product Type
Vertical Through Hole
Drawing Number
Solder Lead Length
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Packaging
Available Positions
2823110
2823114
0.087″ [2.2mm]
2MM-HB-DXXVT-01-T-TB
2823739
2MM-HB-DXXVT-01-T-TBP
2MM-HB-DXXVT-01-F-TB
2823740
2MM-HB-DXXVT-01-F-TBP
2823118
2MM-HB-DXXVT-01-M-TB
2823741
2MM-HB-DXXVT-01-M-TBP
2823122
2MM-HB-DXXVT-01-H-TB
2823742
2MM-HB-DXXVT-01-H-TBP
Tube w/o cap
Tube w/ cap
4~50 6~50
2823110
2823473
2823474
0.110″ [2.8mm]
2MM-HB-DXXVT-01-T-TRP
2823112
2MM-HB-DXXVT-02-T-TB
2823755
2MM-HB-DXXVT-02-T-TBP
2MM-HB-DXXVT-01-F-TRP
2823116
2MM-HB-DXXVT-02-F-TB
2823756
2MM-HB-DXXVT-02-F-TBP
2823475
2MM-HB-DXXVT-01-M-TRP
2823120
2MM-HB-DXXVT-02-M-TB
2823757
2MM-HB-DXXVT-02-M-TBP
2823476
2MM-HB-DXXVT-01-H-TRP
2823124
2MM-HB-DXXVT-02-H-TB
2823758
2MM-HB-DXXVT-02-H-TBP
T&R w/ cap
Tube w/o cap
Tube w/ cap
4~50 4~50 6~50
Horizontal Through Hole
2823477
2823478
2MM-HB-DXX- 2MM-HB-DXXVT-02-T-TRP VT-02-F-TRP
2823126
2823130
0.087″ [2.2mm]
2MM-HB-DXXHT-01-T-TB
2823763
2MM-HB-DXXHT-01-T-TBP
2MM-HB-DXXHT-01-F-TB
2823764
2MM-HB-DXXHT-01-F-TBP
2823479
2MM-HB-DXXVT-02-M-TRP
2823134
2MM-HB-DXXHT-01-M-TB 2823765
2MM-HB-DXXHT-01-M-TBP
2823480
2MM-HB-DXXVT-02-H-TRP
T&R w/ cap
2823138
2MM-HB-DXXHT-01-H-TB 2823766
2MM-HB-DXXHT-01-H-TBP
Tube w/o cap
Tube w/ cap
4~50 4~50 6~50
2823126
Vertical Surface Mount
2823142
2823489
2823490
0.110″ [2.8mm]
2MM-HB-DXXHT-01-T-TRP
2823128
2MM-HB-DXXHT-02-T-TB
2823779
2MM-HB-DXXHT-02-T-TBP
2823493
2MM-HB-DXXHT-02-T-TRP
2MM-HB-DXXHT-01-F-TRP
2823132
2MM-HB-DXXHT-02-F-TB
2823780
2MM-HB-DXXHT-02-F-TBP
2823494
2MM-HB-DXXHT-02-F-TRP
2823491
2MM-HB-DXXHT-01-M-TRP
2823136
2MM-HB-DXXHT-02-M-TB
2823781
2MM-HB-DXXHT-02-M-TBP
2823495
2MM-HB-DXXHT-02-M-TRP
2823492
2MM-HB-DXXHT-01-H-TRP
2823140
2MM-HB-DXXHT-02-H-TB
2823782
2MM-HB-DXXHT-02-H-TBP
2823496
2MM-HB-DXXHT-02-H-TRP
T&R w/ cap
Tube w/o cap
Tube w/ cap
T&R w/ cap
2823142
2823143
2823144
2823145
–
2MM-HBDXX-VS-00-
T-TRP
T&R w/ cap 2MM-HB-DXX- 2MM-HB-DXX- 2MM-HB-DXXVS-00-F-TRP VS-00-M-TRP VS-00-H-TRP
2823787
2823788
2823789
2823790
2MM-HBDXX-VS-00-
T-TBP
2MM-HB-DXX- 2MM-HB-DXX- 2MM-HB-DXXVS-00-F-TBP VS-00-M-TBP VS-00-H-TBP
Tube w/ cap
4~50 4~50 6~50 4~50 4~50
6~50
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
11
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
BREAKAWAY HEADERS
MATEABLE PARTS Breakaway Headers Vertical Orientation
B-t-B Orientation Parallel
2MM – HB – _ _ – VT
Mateable Receptacles
Vertical Board Receptacles
Page 15-16
2MM – R – _ _ – VT
2MM – R – _ _ – VTR
2MM – HB – _ _ – VS
Perpendicular
2MM – R – _ _ – VS Horizontal Board Receptacles
2MM – R – _ _ – HT
Page 15-16
Horizontal Orientation 2MM – HB – _ _ – HT
Perpendicular
2MM – R – _ _ – HS Vertical Board Receptacles
2MM – R – _ _ – VT
2MM – R – _ _ – VTR
Page 15-16
Breakaway Headers Vertical Orientation 2MM – HB – _ _ – VT
2MM – R – _ _ – VS
W-t-B Orientation
Mateable Receptacles
Crimp Receptacles
Page 17-19
2MM – RC – _ _
IDC Receptacles
Single row Only
Page 20-22
2MM – RD- _ _
2MM – HB – _ _ – VS
Horizontal Orientation 2MM – HB – _ _ – HT
Standard (No Latches)
Standard (No Latches)
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
12
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS
SHROUDED HEADERS WITH DETENT LATCHES
SMART PART NUMBER DEFINITION
2MM – HSD – _ _ – _ – _ – _ – _
PRODUCT SERIES
1
2MM AMPMODU 2 mm series
GENDER / TYPE
Shrouded headers with detent HSD
2
latches
NUMBER OF ROWS
S Single row
3
D Double row
NUMBER OF PINS PER ROW
02 thru 25 (enter two digits)
4
## · Single row: 02 thru 16 · Double row: 02 thru 16, 20, 22, 25 per row
PACKAGING
8 TB Tube without cap
Tube with cap TBP (N/A for 2 positions per row)
TRP
Tape and reel with cap (N/A for 2 positions per row for horizontal through hole)
*select allowable Packaging from table DESIGN NAVIGATOR
PLATING T Tin
7 F 4 µ” [0.1 µm] Gold (gold flash)
M 15 µ” [0.38 µm] Gold H 30 µ” [0.76 µm] Gold
ORIENTATION & TERMINATION
TAIL LENGTH
VT Vertical through hole
VS Vertical surface mount
5
00 N/A for surface mount
6 01 0.087″ [2.2 mm]
HT Horizontal through hole
02 0.110″ [2.8 mm]
*see table DESIGN NAVIGATOR for guidance
*select allowable Tail Length from table
SMART PN EXAMPLES
DESIGN NAVIGATOR
· AMPMODU 2 mm, shrouded header with detent latches, single row, 8 positions (1 x 8),horizontal through hole, 2.8 mm tail length, 15µ” [0.38µm] gold, tube without cap:
2MM-HSD-S08-HT-02-M-TB
DESIGN NAVIGATOR
Orientation & Termination VT
Tail Length
Packaging
TB
01
0.087″ [2.2 mm]
TBP
TRP
TB
02
0.110″ [2.8 mm]
TBP
TRP
TRP
VS
00
–
TBP
TB
01
0.087″ [2.2 mm]
TBP
TRP HT
TB
02
0.110″ [2.8 mm]
TBP
TRP
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
13
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS WITH DETENT LATCHES
SINGLE ROW
Product Type
Vertical Through Hole
Drawing Number
Solder Lead Length
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Packaging
0.087″ [2.2mm]
2823372
2823375
2823378
2823381
2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX-
VT-01-T-TB
VT-01-F-TB
VT-01-M-TB
VT-01-H-TB
Tube w/o cap
2823839
2MM-HSD-SXXVT-01-T-TBP
2823840
2MM-HSD-SXXVT-01-F-TBP
2823841
2MM-HSD-SXXVT-01-M-TBP
2823842
2MM-HSD-SXXVT-01-H-TBP
Tube w/ cap
Available Positions
2~16
3~16
2823372
0.110″ [2.8mm]
2823497
2823498
2823499
2823500
2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX-
VT-01-T-TRP
VT-01-F-TRP
VT-01-M-TRP
VT-01-H-TRP
T&R w/ cap
2823373
2823376
2823379
2823382
2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX-
VT-02-T-TB
VT-02-F-TB
VT-02-M-TB
VT-02-H-TB
Tube w/o cap
2823847
2MM-HSD-SXXVT-02-T-TBP
2823848
2MM-HSD-SXXVT-02-F-TBP
2823849
2MM-HSD-SXXVT-02-M-TBP
2823850
2MM-HSD-SXXVT-02-H-TBP
Tube w/ cap
2~16 2~16 3~16
Horizontal Through Hole
2823501
2823502
2823503
2823504
2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX-
VT-02-T-TRP
VT-02-F-TRP VT-02-M-TRP VT-02-H-TRP
T&R w/ cap
2823384
2823387
2823390
2823393
0.087″ [2.2mm]
2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX-
HT-01-T-TB
HT-01-F-TB
HT-01-M-TB
HT-01-H-TB
2823855
2823856
2823857
2823858
2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX-
HT-01-T-TBP
HT-01-F-TBP
HT-01-M-TBP
HT-01-H-TBP
Tube w/o cap
Tube w/ cap
2~16 2~16 3~16
2823384
Vertical Surface Mount 2823396
0.110″ [2.8mm] –
2823513
2MM-HSD-SXXHT-01-T-TRP
2823385
2MM-HSD-SXXHT-02-T-TB
2823863
2MM-HSD-SXXHT-02-T-TBP
2823517
2MM-HSD-SXXHT-02-T-TRP
2823514
2MM-HSD-SXXHT-01-F-TRP
2823388
2MM-HSD-SXXHT-02-F-TB
2823864
2MM-HSD-SXXHT-02-F-TBP
2823518
2MM-HSD-SXXHT-02-F-TRP
2823515
2MM-HSD-SXXHT-01-M-TRP
2823391
2MM-HSD-SXXHT-02-M-TB
2823865
2MM-HSD-SXXHT-02-M-TBP
2823519
2MM-HSD-SXXHT-02-M-TRP
2823516
2MM-HSD-SXXHT-01-H-TRP
2823394
2MM-HSD-SXXHT-02-H-TB
2823866
2MM-HSD-SXXHT-02-H-TBP
2823520
2MM-HSD-SXXHT-02-H-TRP
T&R w/ cap
Tube w/o cap
Tube w/ cap
T&R w/ cap
2823396
2MM-HSD-SXXVS-00-T-TRP
2823397
2MM-HSD-SXXVS-00-F-TRP
2823398
2MM-HSD-SXXVS-00-M-TRP
2823399
2MM-HSD-SXXVS-00-H-TRP
T&R w/ cap
2823871
2823872
2823873
2823874
2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX- 2MM-HSD-SXX-
VS-00-T-TBP
VS-00-F-TBP VS-00-M-TBP VS-00-H-TBP
Tube w/ cap
3~16 2~16 3~16 3~16 2~16 3~16
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
14
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS WITH DETENT LATCHES
DOUBLE ROW
Product Type
Vertical Through Hole
Drawing Number
Solder Lead Length
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] 30µ” [0.76µm]
Gold
Gold
Packaging
Available Positions
0.087″ [2.2mm]
2823335
2823338
2823341
2823344
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
VT-01-T-TB
VT-01-F-TB
VT-01-M-TB
VT-01-H-TB
Tube w/o cap
2823875
2MM-HSD-DXXVT-01-T-TBP
2823876
2MM-HSD-DXXVT-01-F-TBP
2823877
2MM-HSD-DXXVT-01-M-TBP
2823878
2MM-HSD-DXXVT-01-H-TBP
Tube w/ cap
4~32, 40, 44, 50
6~32, 40, 44, 50
2823335
0.110″ [2.8mm]
2823505
2823506
2823507
2823508
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
VT-01-T-TRP
VT-01-F-TRP
VT-01-M-TRP
VT-01-H-TRP
T&R w/ cap
2823336
2823339
2823342
2823345
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
VT-02-T-TB
VT-02-F-TB
VT-02-M-TB
VT-02-H-TB
Tube w/o cap
2823883
2MM-HSD-DXXVT-02-T-TBP
2823884
2MM-HSD-DXXVT-02-F-TBP
2823885
2MM-HSD-DXXVT-02-M-TBP
2823886
2MM-HSD-DXXVT-02-H-TBP
Tube w/ cap
4~32, 40, 44, 50
4~32, 40, 44, 50
6~32, 40, 44, 50
Horizontal Through Hole
2823509
2823510
2823511
2823512
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
VT-02-T-TRP
VT-02-F-TRP VT-02-M-TRP VT-02-H-TRP
T&R w/ cap
2823352
2823355
2823358
2823361
0.087″ [2.2mm]
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
HT-01-T-TB
HT-01-F-TB
HT-01-M-TB
HT-01-H-TB
2823899
2823900
2823901
2823902
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
HT-01-T-TBP
HT-01-F-TBP
HT-01-M-TBP
HT-01-H-TBP
Tube w/o cap
Tube w/ cap
4~32, 40, 44, 50
4~32, 40, 44, 50
6~32, 40, 44, 50
2823351
Vertical Surface Mount 2823367
0.110″ [2.8mm]
2823521
2823522
2823523
2823524
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
HT-01-T-TRP
HT-01-F-TRP
HT-01-M-TRP
HT-01-H-TRP
T&R w/ cap
2823351
2823354
2823357
2823360
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
HT-02-T-TB
HT-02-F-TB
HT-02-M-TB
HT-02-H-TB
Tube w/o cap
2823891
2823892
2823893
2823894
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
HT-02-T-TBP
HT-02-F-TBP
HT-02-M-TBP HT-02-H-TBP
Tube w/ cap
2823525
2MM-HSD-DXXHT-02-T-TRP
2823526
2MM-HSD-DXXHT-02-F-TRP
2823527
2MM-HSD-DXXHT-02-M-TRP
2823528
2MM-HSD-DXXHT-02-H-TRP
T&R w/ cap
2823367
2823368
2823369
2823370
T&R w/ cap
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
–
VS-00-T-TRP
VS-00-F-TRP
VS-00-M-TRP VS-00-H-TRP
2823907
2823908
2823909
2823910
2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX- 2MM-HSD-DXX-
VS-00-T-TBP
VS-00-F-TBP VS-00-M-TBP VS-00-H-TBP
Tube w/ cap
6~32, 40, 44, 50
4~32, 40, 44, 50
6~32, 40, 44, 50
6~32, 40, 44, 50
4~32, 40, 44, 50
6~32, 40, 44, 50
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
15
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS WITH DETENT LATCHES
MATEABLE PARTS
Shrouded Headers w/ Detent Latches
Vertical Orientation
B-t-B Orientation Parallel
Mateable Receptacles
Vertical Board Receptacles
Page 15-16
2MM – HSD – _ _ – VT
2MM – R – _ _ – VT
2MM – HSD – _ _ – VS
Horizontal Orientation 2MM – HSD – _ _ – HT
Perpendicular
2MM – R – _ _ – VTR 2MM – R – _ _ – VS Vertical Board Receptacles 2MM – R – _ _ – VT 2MM – R – _ _ – VTR 2MM – R – _ _ – VS
Page 15-16
Shrouded Headers w/ Detent Latches
Vertical Orientation
W-t-B Orientation
2MM – HSD – _ _ – VT
Crimp Receptacles
Mateable Receptacles
Page 17-19
IDC Receptacles
Single row Only
Page 20-22
2MM – RC – _ _
2MM – RD- _ _
2MM – HSD – _ _ – VS
Horizontal Orientation 2MM – HSD – _ _ – HT
Standard (No Latches)
2MM – RCD – _ _
W/ Detent Latches
Standard (No Latches)
2MM – RDD- _ _
W/ Detent Latches
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
16
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS WITH POSITIVE LATCH
SMART PART NUMBER DEFINITION
2MM – HSP – _ _ – _ – _ – _ – _
PRODUCT SERIES
2MM AMPMODU 2 mm series
1
GENDER / TYPE
HSP
Shrouded headers with positive latch
2
NUMBER OF ROWS
S Single row
3
D Double row
NUMBER OF PINS PER ROW
##
03 thru 16 per row (enter two digits)
4
PACKAGING
TB Tube without cap TBP Tube with cap
8
TR Tape and reel without cap TRP Tape and reel with cap *select allowable Packaging from table DESIGN NAVIGATOR
PLATING
T Tin
M 15 µ” [0.38 µm] Gold
7
H 30 µ” [0.76 µm] Gold
ORIENTATION & TERMINATION
TAIL LENGTH
VT Vertical through hole
VS Vertical surface mount
5
00 N/A for surface mount
6
01 0.087″ [2.2 mm]
HT Horizontal through hole
02 0.110″ [2.8 mm]
*see table DESIGN NAVIGATOR for guidance
*select allowable Tail Length from table DESIGN NAVIGATOR
SMART PN EXAMPLES
· AMPMODU 2 mm, shrouded header with positive latch, double row, 16 positions (2 x 8), vertical through hole, 2.2 mm tail length, 30″ [0.76µm] gold, tube without cap: 2MM-HSP-D08-VT-01-H-TB
DESIGN NAVIGATOR
Orientation & Termination
VT
Tail Length
Packaging
TB
01
0.087″ [2.2 mm]
TBP
TRP
TB
02
0.110″ [2.8 mm]
TBP
TRP
TRP
VS
00
–
TBP
TB
01
0.087″ [2.2 mm]
TR
HT TB
02
0.110″ [2.8 mm]
TR
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
17
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS WITH POSITIVE LATCH
SINGLE ROW
Product Type
Vertical Through Hole
Drawing Number
Solder Lead Length
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Packaging
2823174
Up On Request
2823179
2823183
0.087″ [2.2mm]
2MM-HSP-SXXVT-01-T-TB
2823911
2MM-HSP-SXXVT-01-T-TBP
Up On Request
–
2MM-HSP-SXXVT-01-M-TB
2823912
2MM-HSP-SXXVT-01-M-TBP
2MM-HSP-SXXVT-01-H-TB
2823913
2MM-HSP-SXXVT-01-H-TBP
Tube w/o cap
Tube w/ cap
Available Positions
3~16
3~16
2823174
0.110″ [2.8mm]
2823529
2MM-HSP-SXXVT-01-T-TRP
2823400
2MM-HSP-SXXVT-02-T-TB
2823917
2MM-HSP-SXXVT-02-T-TBP
Up On Request
Up On Request
Up On Request
–
2823530
2MM-HSP-SXXVT-01-M-TRP
2823401
2MM-HSP-SXXVT-02-M-TB
2823918
2MM-HSP-SXXVT-02-M-TBP
2823531
2MM-HSP-SXXVT-01-H-TRP
2823402
2MM-HSP-SXXVT-02-H-TB
2823919
2MM-HSP-SXXVT-02-H-TBP
T&R w/ cap
Tube w/o cap
Tube w/ cap
3~16 3~16 3~16
Horizontal Through Hole
2823187
Vertical Surface Mount 2823199
0.087″ [2.2mm] 0.110″ [2.8mm] –
2823532
2MM-HSP-SXXVT-02-T-TRP
Up On Request –
2823533
2MM-HSP-SXXVT-02-M-TRP
2823534
2MM-HSP-SXXVT-02-H-TRP
T&R w/ cap
2823187
Up On Request
2823191
2823194
2MM-HSP-SXXHT-01-T-TB
2823541
2MM-HSP-SXXHT-01-T-TR
2823403
2MM-HSP-SXXHT-02-T-TB
2823544
2MM-HSP-SXXHT-02-T-TR
Up On Request
Up On Request
Up On Request
–
2MM-HSP-SXXHT-01-M-TB
2823542
2MM-HSP-SXXHT-01-M-TR
2823404
2MM-HSP-SXXHT-02-M-TB
2823545
2MM-HSP-SXXHT-02-M-TR
2MM-HSP-SXXHT-01-H-TB
2823543
2MM-HSP-SXXHT-01-H-TR
2823405
2MM-HSP-SXXHT-02-H-TB
2823546
2MM-HSP-SXXHT-02-H-TR
Tube w/o cap
T&R w/o cap
Tube w/o cap
T&R w/o cap
2823199
2MM-HSP-SXXVS-00-T-TRP
2823929
2MM-HSP-SXXVS-00-T-TBP
Up On Request –
Up On Request –
2823203
2MM-HSP-SXXVS-00-M-TRP
2823930
2MM-HSP-SXXVS-00-M-TBP
2823207
2MM-HSP-SXXVS-00-H-TRP
2823931
2MM-HSP-SXXVS-00-H-TBP
T&R w/ cap
Tube w/ cap
3~16 3~16 3~16 3~16 3~16 3~16 3~16
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
18
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS WITH POSITIVE LATCH
DOUBLE ROW
Product Type
Drawing Number
Vertical Through Hole
2823211
Horizontal Through Hole
2823224
Vertical Surface Mount 2823235
Solder Lead Length
0.087″ [2.2mm]
0.110″ [2.8mm]
0.087″ [2.2mm]
0.110″ [2.8mm]
–
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Packaging
Available Positions
2823211
Up On Request
2823214
2823219
2MM-HSP-DXXVT-01-T-TB
2823932
2MM-HSP-DXXVT-01-T-TBP
Up On Request
–
2MM-HSP-DXXVT-01-M-TB
2823933
2MM-HSP-DXXVT-01-M-TBP
2MM-HSP-DXXVT-01-H-TB
2823934
2MM-HSP-DXXVT-01-H-TBP
Tube w/o cap
Tube w/ cap
6~32 6~32
2823535
2MM-HSP-DXXVT-01-T-TRP
2823406
2MM-HSP-DXXVT-02-T-TB
2823938
2MM-HSP-DXXVT-02-T-TBP
Up On Request
Up On Request
Up On Request
–
2823536
2MM-HSP-DXXVT-01-M-TRP
2823407
2MM-HSP-DXXVT-02-M-TB
2823939
2MM-HSP-DXXVT-02-M-TBP
2823537
2MM-HSP-DXXVT-01-H-TRP
2823408
2MM-HSP-DXXVT-02-H-TB
2823940
2MM-HSP-DXXVT-02-H-TBP
T&R w/ cap
Tube w/o cap
Tube w/ cap
6~32 6~32 6~32
2823538
2MM-HSP-DXXVT-02-T-TRP
Up On Request –
2823539
2MM-HSP-DXXVT-02-M-TRP
2823540
2MM-HSP-DXXVT-02-H-TRP
T&R w/ cap
6~32
2823224
Up On Request
2823228
2823232
2MM-HSP-DXXHT-01-T-TB
2823547
2MM-HSP-DXXHT-01-T-TR
2823409
2MM-HSP-DXXHT-02-T-TB
2823550
2MM-HSP-DXXHT-02-T-TR
Up On Request
Up On Request
Up On Request
–
2MM-HSP-DXXHT-01-M-TB
2823548
2MM-HSP-DXXHT-01-M-TR
2823410
2MM-HSP-DXXHT-02-M-TB
2823551
2MM-HSP-DXXHT-02-M-TR
2MM-HSP-DXXHT-01-H-TB
2823549
2MM-HSP-DXXHT-01-H-TR
2823411
2MM-HSP-DXXHT-02-H-TB
2823552
2MM-HSP-DXXHT-02-H-TR
Tube w/o cap
T&R w/o cap
Tube w/o cap
T&R w/o cap
6~32 6~32 6~32 6~32
2823235
2MM-HSP-DXXVS-00-T-TRP
Up On Request –
2823240
2MM-HSP-DXXVS-00-M-TRP
2823244
2MM-HSP-DXXVS-00-H-TRP
T&R w/ cap
2823950
Up On Request
2823951
2823952
2MM-HSP-DXXVS-00-T-TBP
–
2MM-HSP-DXX- 2MM-HSP-DXXVS-00-M-TBP VS-00-H-TBP
Tube w/ cap
6~32 6~32
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
19
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
SHROUDED HEADERS WITH POSITIVE LATCH
MATEABLE PARTS
Shrouded Headers w/ Positive Latch
W-t-B Orientation
Vertical Orientation
Crimp Receptacles
2MM – HSP – _ _ – VT
Mateable Receptacles
Page 17-19
IDC Receptacles
Single row Only
Page 20-22
2MM – HSP – _ _ – VS
2MM – RCP – _ _
2MM RDP – _ _
Horizontal Orientation 2MM – HSP – _ _ – HT
W/ Positive Latch
W/ Positive Latch
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
20
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
BOARD RECEPTACLES
SMART PART NUMBER DEFINITION
2MM – R – _ _ – _ – _ – _ – _
PRODUCT SERIES
1
2MM AMPMODU 2 mm series
PACKAGING TB Tube without cap
GENDER / TYPE
2
R Receptacle
TBP Tube with cap
8
TR Tape and reel without cap
NUMBER OF ROWS
S Single row
3
D Double row
TRP Tape and reel with cap
*select allowable Packaging from table DESIGN NAVIGATOR
PLATING
NUMBER OF POSITIONS PER ROW
##
02 thru 25 per row (enter two digits)
4
T Tin
F 4µ” [0.1 µm] Gold (Gold flash)
7
M 15µ” [0.38 µm] Gold
ORIENTATION & TERMINATION
H 30µ” [0.76 µm] Gold
VT Vertical through hole
TAIL LENGTH
VTR Vertical through hole outrigger
00 N/A for surface mount
VS Vertical surface mount
5
HT Horizontal through hole
01 0.079 – 0.091″ [2.0 – 2.3 mm]
6
02 0.106 0.110″ [2.7 – 2.8 mm]
HS Horizontal surface mount
03 0.126 0.134″ [3.2 – 3.4 mm]
*see table DESIGN NAVIGATOR for guidance
*select allowable Tail Length from table DESIGN NAVIGATOR
SMART PN EXAMPLES
· AMPMODU 2 mm, board receptacle, double row, 8 positions (2 x 4), horizontal SMT, tail length: N/A, gold flash, T&R without cap: 2MM-R-D04-HS-00-F-TR
DESIGN NAVIGATOR
Orientation & Termination VT
VTR
Tail Length
01
0.079″ [2.0 mm]
02
0.106″ [2.7 mm]
03
0.126″ [3.2 mm]
01
0.091″ [2.3 mm]
02
0.110″ [2.8 mm]
03
0.134″ [3.4 mm]
Packaging TRP TBP TRP TBP TB TB TRP TBP TRP TBP TB TB
TRP
VS
00
–
TBP
TR
01
0.083″ [2.1 mm]
TB
HT
TR
02
0.110″ [2.8 mm]
TB
03
0.134″ [3.4 mm]
TB
TB
HS
00
–
TR
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
21
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
BOARD RECEPTACLES
SINGLE ROW
Product Type
Drawing Number
Vertical Through Hole
Solder Lead Length
0.079″ [2.0mm]
2307764
0.106″ [2.7mm]
Vertical Through Hole
Outrigger
0.126″ [3.2mm] 0.091″ [2.3mm]
2307832
0.110″ [2.8mm]
Vertical Surface Mount
0.134″ [3.4mm]
2307812
–
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Packaging
Available Positions
2307764
2MM-R-SXXVT-01-T-TRP
2314867
2MM-R-SXXVT-01-T-TBP
2307765
2MM-R-SXXVT-02-T-TRP
2314879
2MM-R-SXXVT-02-T-TBP
2314875
2MM-R-SXXVT-02-T-TB
2307766
2MM-R-SXXVT-03-T-TB
2307767
2MM-R-SXXVT-01-F-TRP
2314868
2MM-R-SXXVT-01-F-TBP
2307768
2MM-R-SXXVT-02-F-TRP
2314880
2MM-R-SXXVT-02-F-TBP
2314876
2MM-R-SXXVT-03-F-TB
2307769
2MM-R-SXXVT-03-F-TB
2307770
2MM-R-SXXVT-01-M-TRP
2314869
2MM-R-SXXVT-01-M-TBP
2307771
2MM-R-SXXVT-02-M-TRP
2314881
2MM-R-SXXVT-02-M-TBP
2314877
2MM-R-SXXVT-02-M-TB
2307772
2MM-R-SXXVT-03-M-TB
2307773
2MM-R-SXXVT-01-H-TRP
2314870
2MM-R-SXXVT-01-H-TBP
2307774
2MM-R-SXXVT-02-H-TRP
2314882
2MM-R-SXXVT-02-H-TBP
2314878
2MM-R-SXXVT-02-H-TB
2307775
2MM-R-SXXVT-03-H-TB
T&R w/ cap
Tube w/ cap
T&R w/ cap
Tube w/ cap Tube w/o cap Tube w/o cap
2~25
2307832
2MM-R-SXXVTR-01-T-TRP
2314899
2MM-R-SXXVTR-01-T-TBP
2307833
2MM-R-SXXVTR-02-T-TRP
2314911
2MM-R-SXXVTR-02-T-TBP
2314907
2MM-R-SXXVTR-02-T-TB
2307834
2MM-R-SXXVTR-03-T-TB
2307835
2MM-R-SXXVTR-01-F-TRP
2314900
2MM-R-SXXVTR-01-F-TBP
2307836
2MM-R-SXXVTR-02-F-TRP
2314912
2MM-R-SXXVTR-02-F-TBP
2314908
2MM-R-SXXVTR-02-F-TB
2307837
2MM-R-SXXVTR-03-F-TB
2307838
2MM-R-SXXVTR-01-M-TRP
2314901
2MM-R-SXXVTR-01-M-TBP
2307839
2MM-R-SXXVTR-02-M-TRP
2338990
2MM-R-SXXVTR-02-M-TBP
2314909
2MM-R-SXXVTR-02-M-TB
2307840
2MM-R-SXXVTR-03-M-TB
2307841
2MM-R-SXXVTR-01-H-TRP
2314902
2MM-R-SXXVTR-01-H-TBP
2307842
2MM-R-SXXVTR-02-H-TRP
2314914
2MM-R-SXXVTR-02-H-TBP
2314910
2MM-R-SXXVTR-02-H-TB
2307843
2MM-R-SXXVTR-03-H-TB
T&R w/ cap
Tube w/ cap
T&R w/ cap
Tube w/ cap
Tube w/o cap
Tube w/o cap
2307812
2MM-R-SXXVS-00-T-TRP
2314847
2MM-R-SXXVS-00-T-TBP
2307813
2MM-R-SXXVS-00-F-TRP
2314848
2MM-R-SXXVS-00-F-TBP
2307814
2MM-R-SXXVS-00-M-TRP
2314849
2MM-R-SXXVS-00-M-TBP
2307815
2MM-R-SXXVS-00-H-TRP
2314850
2MM-R-SXXVS-00-H-TBP
T&R w/ cap
Tube w/ cap
2~25 2~25
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
22
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
Product Type
Horizontal Through Hole
Drawing Number
Solder Lead Length
0.083″ [2.1mm]
2307700
0.110″ [2.8mm]
Horizontal Surface Mount
0.134″ [3.4mm]
2307724
–
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] 30µ” [0.76µm]
Gold
Gold
2307700
2307703
2307706
2307709
2MM-R-SXXHT-01-T-TR
2314927
2MM-R-SXXHT-01-T-TB
2314935
2MM-R-SXXHT-02-T-TR
2307701
2MM-R-SXXHT-02-T-TB
2307702
2MM-R-SXXHT-03-T-TB
2MM-R-SXXHT-01-F-TR
2314928
2MM-R-SXXHT-01-F-TB
2314936
2MM-R-SXXHT-02-F-TR
2307704
2MM-R-SXXHT-02-F-TB
2307705
2MM-R-SXXHT-03-F-TB
2MM-R-SXXHT-01-M-TR
2314929
2MM-R-SXXHT-01-M-TB
2314937
2MM-R-SXXHT-02-M-TR
2307707
2MM-R-SXXHT-02-M-TB
2307708
2MM-R-SXXHT-03-M-TB
2MM-R-SXXHT-01-H-TR
2314930
2MM-R-SXXHT-01-H-TB
2314938
2MM-R-SXXHT-02-H-TR
2307710
2MM-R-SXXHT-02-H-TB
2307711
2MM-R-SXXHT-03-H-TB
2307724
2307725
2307726
2307727
2MM-R-SXXHS-00-T-TR
2314943
2MM-R-SXXHS-00-T-TB
2MM-R-SXXHS-00-F-TR
2314944
2MM-R-SXXHS-00-F-TB
2MM-R-SXXHS-00-M-TR
2314945
2MM-R-SXXHS-00-M-TB
2MM-R-SXXHS-00-H-TR
2314946
2MM-R-SXXHS-00-H-TB
Packaging
T&R w/o cap
Tube w/ cap
T&R w/o cap
Tube w/ cap
Tube w/ cap
T&R w/ cap
Tube w/ cap
Available Positions
2~25
2~25
DOUBLE ROW
Product Type
Vertical Through Hole
Drawing Number
Solder Lead Length
0.079″ [2.0mm]
2307776 0.106″ [2.7mm] 0.126″ [3.2mm]
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Packaging
2307776
2MM-R-DXXVT-01-T-TRP
2314811
2MM-R-DXXVT-01-T-TBP
2307777
2MM-R-DXXVT-02-T-TRP
2314823
2MM-R-DXXVT-02-T-TBP
2314819
2MM-R-DXXVT-02-T-TB
2307778
2MM-R-DXXVT-03-T-TB
2307779
2MM-R-DXXVT-01-F-TRP
2314812
2MM-R-DXXVT-01-F-TBP
2307780
2MM-R-DXXVT-02-F-TRP
2314824
2MM-R-DXXVT-02-F-TBP
2314820
2MM-R-DXXVT-02-F-TB
2307781
2MM-R-DXXVT-03-F-TB
2307782
2MM-R-DXXVT-01-M-TRP
2314813
2MM-R-DXXVT-01-M-TBP
2307783
2MM-R-DXXVT-02-M-TRP
2314825
2MM-R-DXXVT-02-M-TBP
2314821
2MM-R-DXXVT-02-M-TB
2307784
2MM-R-DXXVT-03-M-TB
2307785
2MM-R-DXXVT-01-H-TRP
2314814
2MM-R-DXXVT-01-H-TBP
2307786
2MM-R-DXXVT-02-H-TRP
2314826
2MM-R-DXXVT-02-H-TBP
2314822
2MM-R-DXXVT-02-H-TB
2307787
2MM-R-DXXVT-03-H-TB
T&R w/ cap
Tube w/ cap
T&R w/ cap
Tube w/ cap Tube w/o cap Tube w/o cap
Available Positions
4~50
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
23
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
Product Type
Drawing Number
Solder Lead Length
Vertical Through Hole Outrigger
0.091″ [2.3mm]
2307820
0.110″ [2.8mm]
Vertical Surface Mount
0.134″ [3.4mm]
2307816
–
Horizontal Through Hole
0.083″ [2.1mm]
2307712
0.110″ [2.8mm]
Horizontal Surface Mount
0.134″ [3.4mm]
2307728
–
Base Number / Smart Part Number
Tin
4µ” [0.1µm] Gold
15µ” [0.38µm] 30µ” [0.76µm] Packaging
Gold
Gold
2307820
2MM-R-DXXVTR-01-T-TRP
2314851
2MM-R-DXXVTR-01-T-TBP
2307821
2MM-R-DXXVTR-02-T-TRP
2314863
2MM-R-DXXVTR-02-T-TBP
2314859
2MM-R-DXXVTR-02-T-TB
2307822
2MM-R-DXXVTR-03-T-TB
2307823
2MM-R-DXXVTR-01-F-TRP
2314852
2MM-R-DXXVTR-01-F-TBP
2307824
2MM-R-DXXVTR-02-F-TRP
2314864
2MM-R-DXXVTR-02-F-TBP
2314860
2MM-R-DXXVTR-02-F-TB
2307825
2MM-R-DXXVTR-03-F-TB
2307826
2MM-R-DXXVTR-01-M-TRP
2314853
2MM-R-DXXVTR-01-M-TBP
2307827
2MM-R-DXXVTR-02-M-TRP
2314865
2MM-R-DXXVTR-02-M-TBP
2314861
2MM-R-DXXVTR-02-M-TB
2307828
2MM-R-DXXVTR-03-M-TB
2307829
2MM-R-DXXVTR-01-H-TRP
2341413
2MM-R-DXXVTR-01-H-TBP
2307830
2MM-R-DXXVTR-02-H-TRP
2314866
2MM-R-DXXVTR-02-H-TBP
2314862
2MM-R-DXXVTR-02-H-TB
2307831
2MM-R-DXXVTR-03-H-TB
T&R w/ cap
Tube w/ cap
T&R w/ cap
Tube w/ cap
Tube w/o cap
Tube w/o cap
2307816
2MM-R-DXXVS-00-T-TRP
2314843 2MM-R-DXXVS-00-T-TBP
2307817
2MM-R-DXXVS-00-F-TRP
2314844 2MM-R-DXXVS-00-F-TBP
2307818
2MM-R-DXXVS-00-M-TRP
2314845 2MM-R-DXXVS-00-M-TBP
2307819
2MM-R-DXXVS-00-H-TRP
2314846 2MM-R-DXXVS-00-H-TBP
T&R w/ cap
Tube w/ cap
2307712
2MM-R-DXXHT-01-T-TR
2314915
2MM-R-DXXHT-01-T-TB
2314923
2MM-R-DXXHT-02-T-TR
2307713
2MM-R-DXXHT-02-T-TB
2307714
2MM-R-DXXHT-03-T-TB
2307715
2MM-R-DXXHT-01-F-TR
2314916
2MM-R-DXXHT-01-F-TB
2314924
2MM-R-DXXHT-02-F-TR
2307716
2MM-R-DXXHT-02-F-TB
2307717
2MM-R-DXXHT-03-F-TB
2307718
2MM-R-DXXHT-01-M-TR
2314917
2MM-R-DXXHT-01-M-TB
2314925
2MM-R-DXXHT-02-M-TR
2307719
2MM-R-DXXHT-02-M-TB
2307720
2MM-R-DXXHT-03-M-TB
2307721
2MM-R-DXXHT-01-H-TR
2314918
2MM-R-DXXHT-01-H-TB
2314926
2MM-R-DXXHT-02-H-TR
2307722
2MM-R-DXXHT-02-H-TB
2307723
2MM-R-DXXHT-03-H-TB
T&R w/o cap
Tube w/o cap
T&R w/o cap
Tube w/o cap
Tube w/o cap
2307728
2MM-R-DXXHS-00-T-TR
2307729
2MM-R-DXXHS-00-F-TR
2307730
2MM-R-DXXHS-00-M-TR
2307731
2MM-R-DXXHS-00-H-TR
T&R w/o cap
2314939
2MM-R-DXXHS-00-T-TB
2314940
2MM-R-DXXHS-00-F-TB
2314941
2MM-R-DXXHS-00-M-TB
2314942
2MM-R-DXXHS-00-H-TB
Tube w/o cap
Available Positions
4~50
4~50 4~50 4~50
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
24
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
BOARD RECEPTACLES
MATEABLE PARTS Board Receptacles Vertical Orientation
B-t-B Orientation Parallel
Mateable Headers
Vertical Breakaway Headers
Page 9-10
2MM – HB – _ _ – VT
2MM – R – _ _ – VT 2MM – R – _ _ – VTR
Parallel
2MM – HB – _ _ – VS
Vertical Shrouded Headers w/ Detent Latches
2MM – HSD – _ _ – VT
Page 11-12
2MM – R – _ _ – VS
Horizontal Orientation 2MM – R – _ _ – HT 2MM – R – _ _ – HS
Perpendicular Perpendicular Perpendicular
2MM – HSD – _ _ – VS Horizontal Breakaway
Headers
2MM – HB – _ _ – HT
Horizontal Shrouded Headers w/ Detent Latches
2MM – HSD – _ _ – HT
Vertical Breakaway Headers
2MM – HB – _ _ – VT
Page 9-10 Page 11-12 Page 9-10
2MM – HB – _ _ – VS
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
25
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM CRIMP SNAP-IN RECEPTACLES
SMART PART NUMBER DEFINITION
2MM – _ – _ _ – BX
PRODUCT SERIES
2MM AMPMODU 2 mm series
1
PACKAGE
5
BX Box
GENDER / TYPE
4
Unloaded standard receptacle RC housing (no latches)
Unloaded receptacle housing
RCD
with detent latches
2
3
Unloaded receptacle housing
RCP with positive latch
SMART PN EXAMPLES · AMPMODU 2 mm, crimp receptacle with detent latches, double row, 16 positions (2 x 8), box: 2MM-RCD-D08-BX
NUMBER OF POSITIONS PER ROW 02 thru 25 per row
## (enter two digits)
*refer to table DESIGN NAVIGATOR for allowable position sizes
NUMBER OF ROWS S Single row D Double row
DESIGN NAVIGATOR Housing Style
Standard (no latches)
Number of Rows Single row
Double row
Number of Positions per Row Packaging Method 02 thru 25
02 thru 25 per row
With detent latches
Single row Double row
07 thru 16 Box
07 thru 16, 20, 22, 25 per row
With positive latch
Single row Double row
* Tube packaging is available upon request.
03 thru 16 03 thru 16 per row
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
26
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
CRIMP SNAP-IN RECEPTACLES
RECEPTACLE CONTACT
2MM – RT – _ – _ – _
PRODUCT SERIES
2MM AMPMODU 2 mm series
1
GENDER / TYPE
2
RT Receptacle crimp contact
WIRE SIZE
S AWG 30-28 [0.05 – 0.08 mm²]
3
M AWG 28-24 [0.08 0.22 mm²]
SMART PN EXAMPLES · AMPMODU 2 mm, crimp receptacle contact, AWG 30 – 28, tin, 30kpcs/reel: 2MM-RT-S-T-ST
APPLICATION TOOLING Tooling
Images
Contact Package
Hand tool
Loose Piece (LP)
PACKAGING
5
ST Strip form (30K pcs/reel)
LP Loose piece
PLATING
T Tin
F 4 µ” [0.1 µm] gold (gold flash)
4
M 15 µ” [0.38 µm] gold
H 30 µ” [0.76 µm] gold
Contact AWG 30-28
2326270-1
Contact AWG 28-24
2326267-1
Ocean applicator Extraction tool
30k pcs per/reel (ST)
Upon request
Upon request
9-1579028-8 Suitable for all receptacles to disengage locking lance from front window.
843477-3 Suitable for standard and detent latch receptacles only to disengage locking lance from side, top or bottom windows.
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
27
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
CRIMP SNAP-IN RECEPTACLES
SINGLE ROW
Product Type Standard (no latches)
Drawing Number 2316102
With detent latches
2316103
With positive latch
2316104
Base Number 2316102
2MM-RC-SXX-BX 2316103
2MM-RCD-SXX-BX 2316104
2MM-RCP-SXX-BX
Available Positions 2~25 7~16 3~16
DOUBLE ROW Product Type
Standard (no latches)
With detent latches
With positive latch
Drawing Number 2316108 2316109 2316110
Base Number 2316108
2MM-RC-DXX-BX 2316109
2MM-RCD-DXX-BX 2316110
2MM-RCP-DXX-BX
Available Positions 4~50
14~32, 34, 40, 44, 50 6~32
RECEPTACLE CONTACTS
Wire Size
Product Image
AWG 28-24 [0.08 – 0.22 mm2]
AWG 30-28 [0.05 – 0.08 mm2]
Drawing Number
Plating
Tin
2316113
4µ” [0.1µm] Gold 15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Tin
2316114
4µ” [0.1µm] Gold 15µ” [0.38µm] Gold
30µ” [0.76µm] Gold
Packaging Method
30Kpc Reel
Loose Piece
2-2316113-2
2-2316113-3
2MM-RT-M-T-ST
2MM-RT-M-T-LP
3-2316113-3
3-2316113-4
2MM-RT-M-F-ST
2MM-RT-M-F-LP
4-2316113-4
4-2316113-5
2MM-RT-M-M-ST
2MM-RT-M-M-LP
5-2316113-5
5-2316113-6
2MM-RT-M-H-ST
2MM-RT-M-H-LP
2-2316114-2
2-2316114-3
2MM-RT-S-T-ST
2MM-RT-S-T-LP
3-2316114-3
3-2316114-4
2MM-RT-S-F-ST
2MM-RT-S-F-LP
4-2316114-4
4-2316114-5
2MM-RT-S-M-ST
2MM-RT-S-M-LP
5-2316114-5
5-2316114-6
2MM-RT-S-H-ST
2MM-RT-S-H-LP
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
28
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
CRIMP SNAP-IN RECEPTACLES
MATEABLE PARTS
Wire Receptacles
W-t-B Orientation
Standard (No Latches)
Mateable Headers
Vertical Breakaway
Headers
Page 9-10
2MM – HB – _ _ – VT
Vertical Shrouded Headers
w/ Detent Latches
Page 11-12
2MM – HSD – _ _ – VT
2MM – RC – _ _
2MM – HB – _ _ – VS
2MM – HSD – _ _ – VS
Horizontal Breakaway
Headers
Page 9-10
2MM – HB – _ _ – HT
Horizontal Shrouded Headers w/ Detent Latches
Page 11-12
2MM – HSD – _ _ – HT
w/ Detent Latches
Vertical Shrouded Headers w/ Detent Latches
2MM – HSD – _ _ – VT
2MM – RCD – _ _ w/ Positive Latch
2MM – HSD – _ _ – VS Horizontal Shrouded Headers
w/ Detent Latches 2MM – HSD – _ _ – HT Vertical Shrouded Headers
w/ Positive Latch 2MM – HSP – _ _ – VT
2MM – RCP – _ _
2MM – HSP – _ _ – VS Horizontal Shrouded Headers
w/ Positive Latch 2MM – HSP – _ _ – HT
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM Downloaded from Arrow.com.
Page 11-12 Page 11-12 Page 13-14 Page 13-14
29
AMPMODU 2 MM INTERCONNECTION SYSTEM
INSULATION DISPLACEMENT CONTACT
INSULATION DISPLACEMENT CONTACT (IDC) RECEPTACLES
SMART PART NUMBER DEFINITION
2MM – _ – S _ – S – _ – TB
PRODUCT SERIES
2MM AMPMODU 2 mm series
1
PACKAGING
7
TB Tube
GENDER / TYPE
Standard IDC receptacle
RD
(no latches)
2
RDD IDC Receptacle with detent latches
RDP IDC receptacle with positive latch
NUMBER OF ROWS
3
S Single row
PLATING
6
T Tin F 4 µ” [0.1 µm] gold (gold flash)
(N/A with positive latch) M 15 µ” [0.38 µm] gold H 30 µ” [0.76 µm] gold
NUMBER OF POSITIONS PER ROW
## 02 thru 12 (enter two digits)
4
WIRE SIZE
5
S AWG 30-26 [0.05 0.14 mm2]
*see table DESIGN NAVIGATOR for available positions
SMART PN EXAMPLES · AMPMODU 2 mm, IDC receptacle with positive latch, single row, 7 positions (1 x 7), AWG 30 – 26, 30µ” [0.76 m] gold, tube: 2MM-RDP-S07-S-H-TB
RECEPTACLE HOUSINGS Type
Standard (no latches)
Images
With detent latches With positive latch
Wire size
AWG 30-26 [0.05 0.14
mm2]
Plating 30 µ” [0.76 µm] gold 15 µ” [0.38 µm] gold
4 µ” [0.1 µm] gold Tin
30 µ” [0.76 µm] gold 15 µ” [0.38 µm] gold
4 µ” [0.1 µm] gold Tin
30 µ” [0.76 µm] gold 15 µ” [0.38 µm] gold
Tin
Number of Positions 02 thru 12 07 thru 12 03 thru 12
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
30
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
INSULATION DISPLACEMENT CONTACT (IDC) RECEPTACLES
APPLICATION TOOLING Tooling
Images
TE Part Number
Terminating head*
2326300-1
Pistol grip manual handle*
58074-1
Pneumatic handle*
58075-1
9-1579028-8
Extraction tool
Suitable for all receptacles to disengage locking lance from front window.
843477-3 Suitable for standard and detent latch receptacles only to disengage locking lance from side, top or bottom windows.
*Terminating head needs to be used with the manual or pneumatic handle.
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
31
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
INSULATION DISPLACEMENT CONTACT (IDC) RECEPTACLES
Product Type Standard (no latches)
With detent latches
With positive latch
Drawing Number 2317222 2317223 2317224
Wire Size AWG 30-26 [0.05 0.14
mm2] AWG 30-26 [0.05 0.14
mm2] AWG 30-26 [0.05 0.14
mm2]
Plating 30µ” [0.76µm] Gold 15µ” [0.38µm] Gold
4µ” [0.1µm] Gold Tin
30µ” [0.76µm] Gold 15µ” [0.38µm] Gold
4µ” [0.1µm] Gold Tin
30µ” [0.76µm] Gold 15µ” [0.38µm] Gold
4µ” [0.1µm] Gold Tin
Base Number
2317206
2MM-RD-SXX-SH-TB
2317205
2MM-RD-SXX-SM-TB
2317204
2MM-RD-SXX-SF-TB
2317222
2MM-RD-SXX-ST-TB
2317209
2MM-RDD-SXX-SH-TB
2317208
2MM-RDD-SXX-SM-TB
2317207
2MM-RDD-SXX-SF-TB
2317223
2MM-RDD-SXX-ST-TB
2317212
2MM-RDP-SXX-SH-TB
2317211
2MM-RDP-SXX-SM-TB
Up on request
Up on request
2317224
2MM-RDP-SXX-ST-TB
Available Positions 2, 3, 4, 5, 6
7, 8, 9, 10, 11, 12
7, 8, 9, 10, 11, 12
3, 4, 5, 6 7, 8, 9, 10, 11, 12
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM
32
Downloaded from Arrow.com.
AMPMODU 2 MM INTERCONNECTION SYSTEM
INSULATION DISPLACEMENT CONTACT (IDC) RECEPTACLES
MATEABLE PARTS Single row Only
Wire Receptacles
W-t-B Orientation
Mateable Headers
Standard (No Latches)
Vertical Breakaway
Headers
Page 9-10
2MM – HB – _ _ – VT
Vertical Shrouded Headers
w/ Detent Latches
Page 11-12
2MM – HSD – _ _ – VT
2MM – RD – _ _
2MM – HB – _ _ – VS
2MM – HSD – _ _ – VS
Horizontal Breakaway
Headers
Page 9-10
2MM – HB – _ _ – HT
Horizontal Shrouded Headers w/ Detent Latches
Page 11-12
2MM – HSD – _ _ – HT
w/ Detent Latches
Vertical Shrouded Headers w/ Detent Latches
2MM – HSD – _ _ – VT
2MM – RDD – _ _ w/ Positive Latch
2MM – HSD – _ _ – VS Horizontal Shrouded Headers
w/ Detent Latches 2MM – HSD – _ _ – HT Vertical Shrouded Headers
w/ Positive Latch 2MM – HSP – _ _ – VT
2MM – RDP – _ _
2MM – HSP – _ _ – VS Horizontal Shrouded Headers
w/ Positive Latch 2MM – HSP – _ _ – HT
INDUSTRIAL / AMPMODU 2 MM INTERCONNECTION SYSTEM Downloaded from Arrow.com.
Page 11-12 Page 11-12 Page 13-14 Page 13-14
33
AMPMODU 2 MM INTERCONNECTION SYSTEM
© 2023 TE Connectivity. All Rights Reserved.
AMPMODU, TE Connectivity, TE connectivity (logo) and EVERY CONNECTION COUNTS are trademarks owned or licensed by TE Connectivity. All other logos, products and/or company names referred to herein might be trademarks of their respective owners.
While TE has made every reasonable effort to ensure the accuracy of the information in this brochure, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this catalog are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.
Documents / Resources
 |
TE Connectivity 2MM-RD-S12-S-T-TB Amp Modu 2 Mm Interconnection System [pdf] Instructions 2MM-RD-S12-S-T-TB, 108-64040, 108-64040-1, 108-64040-2, 114-64040, 114-32186, 114-32173, 114-32175, 2MM-RD-S12-S-T-TB Amp Modu 2 Mm Interconnection System, 2MM-RD-S12-S-T-TB, Amp Modu 2 Mm Interconnection System, Mm Interconnection System, Interconnection System, System |