ALTO 6
2.0 Channel Sound Bar with Dolby Audio
Quick Start Guide
What’s in the box
Make sure you read all the safety information
before you use this product.
2a Overview
Sound Bar main unit
AC input power connector
AUX input connector
Optical input connector
HDMI ARC connector
USB Type-A connector 
Place your Sound Bar
The ideal place to position the Sound Bar is
centered underneath your TV.
Wall mount your Sound BarRequired tools:
- Place the supplied wall-mount template on the wall. Make sure the wall mount template is at least 2 inches below the center of the TV.
- Use a level to make sure the wall mount template is positioned accurately.
- Use the tape to stick the wall mount template firmly on the wall.
- Mark on the wall using each marking on the template through the mounting holes.
- Take away the wall mount template.
- Drill a screw hole at each marking on the wall.
Wall mount your Sound Bar
Required tools:
- Insert the wall anchors in the holes on the wall.
- Insert the supplied screws into the hole of the wall anchors.
- Fix and tighten the wall bracket screws on the wall, but leave a little space for hanging the brackets.
Wall mount your Sound Bar
Required tools:• Unscrew the rubber cushions from the bottom of the soundbar and set them aside for potential use in the future 10
• Attach the included wall bracket mounts to the sound bar in the same holes the rubber cushions were removed from. 11
• With the brackets now attached to the soundbar, pick up the soundbar and attach it to the wall screws, similar to how you would hang a picture. Make sure everything is tight. 12
Connect to your TV
There are 3 ways to connect your sound bar to the TV (listed in the order that we recommend): HDMI ARC (refer to 4a), Optical (refer to 4b), and AUX (refer to 4c)
For the USA only: If you have a Roku TV TM, simply plug in the HDMI cable and follow the Roku TV Ready TM on-screen instructions.
ROKU TV READY
Simple setup
One remote
Quick settings
HDMI-ARC
Connect the Sound Bar with your TV through the supplied HDMI cable.
Connect the Sound Bar to the power supply with the supplied power cord.
Optical
Connect the Sound Bar with your TV through the supplied Optical cable.
Connect the Sound Bar to the power supply with the supplied power cord.
AUX
Connect the Sound Bar with your TV through AUX cable (not supplied).
Connect the Sound Bar to the power supply with the supplied power cord.
Install or replace the remote batteries
Battery Type: 1.5V AAA Alkaline battery x 2
Using the Remote
Pair with your
Bluetooth device
You can stream music from your mobile device via Bluetooth.
1. Press.
2. Press.
3. Press and hold or
on the remote control or press and hold on your soundbar.
> You hear a sound signal and blue light is flashing on the soundbar.
> The Sound Bar is ready to pair.
4. Power on your Bluetooth device and activate its Bluetooth function.
5. Select TCL Alto 6.
> You hear a sound signal.
> Pairing is successful.
6. If you want to re-pair with another device, please repeat step 3.
Sound Bar LED Display
The LED display on the Sound Bar gives your information about the status of the Sound Bar.
| Sound Bar status | LED Indications |
| In standby mode | Red |
| In HDMI ARC mode | Purple |
| In OPT mode | Yellow |
| In AUX mode | Green |
| In USB mode | Cyan |
| In Bluetooth mode | Blue |
FAQ
Does this Sound Bar work with any TV?
Yes, the Sound Bar is compatible with any TV that has one of the ports below:
1. HDMI supporting ARC (preferred)
2. Optical audio output (TOSLink)
3. Headphone output
When the Sound Bar and TV are both on, there is an echo effect.
If you use an HDMI-ARC connection, please check if the HDMI-CEC feature of your TV is turned on. This feature may be
called T-Link, Anynet+, SimpLink, BRAVIA Link, EasyLink, or VIERA Link.
If using an optical or AUX connection, simply mute the TV speaker.
How many sound modes are available?
Three sound modes – Movie, Music, and TV.
How to clean the sound bar?
Please keep your soundbar in a dry and ventilated environment.
If it needs to be cleaned, please wipe it gently with a soft, dry cloth without water or other cleaning agents.
All technology names mentioned are the trademarks or registered trademarks of their respective companies.
DO NOT RETURN TO THE STORE
WEARE READY TO HELP contact us first with any questions
support.tclusa.com
support.tclcanada.com
or TCL SUPPORT: 1-877-300-9223
TAKE CARE WHEN REMOVING THE SOUNDBAR
ROKU TV READY
Roku TV, Roku TV Ready, and the Roku TV Ready logo are trademarks of Roku, Inc.
The Adopted Trademarks HDMI, HDMIHigh-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries. 
The Bluetooth° word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by TTE Corporation is under license. Other trademarks and trade names are those of their respective owners.
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
Copyright © 2020 TCL.
All rights reserved.
TS6100_NA_QSG_V1.8
Documents / Resources
 | TCL ALTO 6 2.0 Channel Sound Bar with Dolby Audio [pdf] User Guide TCL, ALTO 6, 2.0 Channel, Sound Bar, with, Dolby Audio |
 | TCL ALTO 6 2.0 Channel Sound Bar with Dolby Audio [pdf] User Guide TS6100, 2ARUDTS6100, ALTO 6, 2.0 Channel Sound Bar with Dolby Audio, ALTO 6 2.0 Channel Sound Bar with Dolby Audio, Sound Bar with Dolby Audio |
