TASCAM CD200SB CD Solid State Player
SCHEMATIC DIAGRAM
SAFETY INFORMATION
CAUTIONS ABOUT LASER RADIATION
This product has been designed and manufactured according to FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of 1968,” and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings.
The label required in this regulation is shown at ➀.
Cautions
i DO NOT REMOVE THE PROTECTIVE HOUSING USING A SCREWDRIVER.
i USE OF CONTROLS OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
i IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE THE PRODUCT IN
ITS DAMAGED STATE.
Specifications
Supported media types
CD, CD-R and CD-RW discs
(including 12cm, 8cm and multisession discs and discs with CD
text)
The following types of media must be formatted in FAT16 or
FAT32 format.
USB (4GB–64GB)
SD (2GB)
SDHC (4GB–32GB)
Playback file formats
CD-DA : 44.1kHz, 16-bit stereo
MP2 : 32/44.1/48kHz, 32–320kbps
(data CDs/SD cards/USB flash drives)
MP3 : 32/44.1/48kHz, 32–320kbps, VBR
(data CDs/SD cards/USB flash drives)
WAV : 8/16/32/11.025/22.05/44.1/12/24/48kHz, 16-bit
(data CDs/SD cards/USB flash drives)
AAC* : 32/44.1/48kHz, 32–320kbps, VBR
(SD cards/USB flash drives)
WMA** : 32/44.1/48kHz, 32–384kbps, VBR
(SD cards/USB flash drives)
* : AAC DRM not supported
** : WMA files must be compliant with Ver. 9 Standard; DRM is not
supported
Playback file formats
WAV : 44.1kHz, 16-bit stereo
MP3 : 44.1kHz, 64/128/256kbps
Analog audio output ratings
ANALOG OUTPUT (BALANCED)
Connector : XLR-3-32 (1: GND, 2: HOT, 3: COLD)
Output impedance : 200 Ω
Reference Output Level : +4 dBu (1.23 Vrms)
Maximum Output Level : +20 dBu (7.75 Vrms)
ANALOG OUTPUT (UNBALANCED)
Connector : RCA pin jacks
Output impedance : 200 Ω
Reference Output Level : –10 dBV (0.32 Vrms)
Maximum Output Level : +6 dBV (2.0 Vrms)
PHONES output
Connector : φ 6.3 mm (1/4′) Stereo Phone Jack
Maximum Output Level : 20 mW + 20 mW
(THD+N: 0.1%, 32Ω)
Digital audio output ratings
DIGITAL OUTPUT (COAXIAL)
Connector : RCA Pin Jack
Compatible Signal Format : IEC-60958-3 (S/PDIF)
DIGITAL OUTPUT (OPTICAL)
Connector : Optical Jack
Compatible Signal Format : IEC-60958-3 (S/PDIF)
Audio performance
Frequency response
20 Hz – 20 kHz : ±1.0 dB (during playback, JEITA)
Signal-to-Noise Ratio (S/N)
More than 90 dB (during playback, JEITA)
Total Harmonic Distortion
Less than 0.01% (during playback, JEITA)
Dynamic range
More than 90 dB (during playback, JEITA)
Channel Separation
More than 90 dB (during playback, JEITA)
Backup memory
The following settings are backed up even when the unit power is
turned off.
⿎ Time and title display settings
⿎ Playback mode
⿎ Program (CD/SD card/USB flash drive)
⿎ Current folder (CD/SD card/USB flash drive)
⿎ Media selection
⿎ Repeat playback function setting (ON/OFF)
⿎ Pitch control ON/OFF (CD)
General
Power Requirement
AC 120 V, 60 Hz (U.S.A./Canada)
AC 230 V, 50 Hz (U.K./Europe)
AC 240 V, 50 Hz (Australia)
Power consumption
11 W
Dimensions (W x H x D)
481 x 94.5 x 298 (mm) / 18.94 x 3.72 x 11.73 (inc)
Weight
4.7 kg (10.36 lb)
Operating temperature range
5 to 35°C
Installation angle
5º or less
Dimensional drawings
Test Mode and Special Operations
1. How to enter test mode
The test mode is intended for use in the pre-shipping inspection at the
factory and in the maintenance after shipment.
1) How to enter test mode
With no disc loaded in the CD player, hold down the STOP and REW
SEARCH buttonson the main unit, press the POWER switch to
turn the unit on.
NOTE
Even after “WELCOME” appears on the display, keep pressing the
STOP and REW SEARCH buttons until “TEST MD” appears.
“TEST MD” is displayed to indicate that the test mode menu is
available.
The test mode is exited when the system is turned OFF.
2) Test mode menu
Press the FOLDER g/t button to select a test item, and press the
REPEAT button to enter the selection.
To return to the test mode menu from the selected item, press the
DISPLAY button.
[1] “LCD TEST” LCD/LED display testing
① In the test mode menu, display “n02 LCD TEST” and press
the REPEAT button.
② All of the LCDs/LEDs (CD PITCH CONTROL) light up.
③ Each press of the FOLDER g/t button switches the lighting conditions as follows.
i All LCDs/LEDs (CD PITCH CONTROL) lit.
i All LCDs/LEDs (CD PITCH CONTROL) extinguished.
i [Eight] characters “01234567” lit in the LCD text area.
④ Press the DISPLAY button during testing to finish it and return to the test mode menu.
[2] “KEY TEST” Front button testing
① In the test mode menu, display “n03 KEY TEST” and press
the REPEAT button.
② When the name of the button to be checked is displayed,
press the corresponding button.
When the button check result is OK, the name of the next
button is displayed. If the button check result is NG (No
Good), the displayed button name does not change.
The front button testing begins with the OPEN/CLOSE
button and continues from the left to the right. When the
rightmost button in a row has been tested, the buttons in
the next row are tested from the left end toward the right
end.
The last button tested is the DISPLAY button.
③ “COMPLETE” is displayed when all of the front buttons
have been checked.
④ Press the DISPLAY or REPEAT button to return to the test
mode menu.
[3] “FACT DEF” EEPROM initialization (For use in factory)
NOTE
This test is designed exclusively for the pre-shipping inspection at
the factory. It is used after replacement of the CD drive mechanism to
clear the total run time count of the mechanism.
① The EEPROM initialization is for use in pre-shipping inspection at the factory. It clears the total run time count of the
CD drive but does not clear the total power ON time count.
② In the test mode menu, display “n04 FACT DEF” and press
the REPEAT button.
③ “EEPR CLR” is displayed when the EEPROM has been initialized.
④ Press the DISPLAY button to return to the test mode menu.
[4] “REM TEST” IR remote control testing
① In the test mode menu, display “n05 REM TEST” and press
the REPEAT button.
② Press each remote control button and confirm that its name
is displayed.
③ Press the REPEAT or DISPLAY button. during testing to
finish it and return to the test mode menu
[5] “LIF TIM” Total power ON time check
NOTE
Since the EEPROM on the front PCB stores various total run time data,
the total power ON time is cleared when the front PCB is replaced.
① In the test mode menu, display “n06 LIFE TIM” and press
the REPEAT button.
② “LH” is displayed together with the total power ON time
count. (Units : hour).
This data is always counted while the system is turned ON.
It cannot be cleared.
③ Press the DISPLAY button to return to the test mode menu.
2. Special Displays
The special displays are for use in the pre-shipping inspection
at the factory and in the support after shipment.
1) Confirmation of firmware version
This display shows the version number of the firmware used in the unit.
① Turn the unit off and remove the SD card and USB flash
drive. Then, while pressing and holding both the STOP
and REPEAT buttons on the main unit, press the POWER
switch to turn the unit on.
NOTE
Even after “WELCOME” appears on the display, keep pressing the
STOP and REPEAT buttons until “VERSION” appears.
② Check the following information items by using the FOLDER
g/t buttons to change the item shown.
i VERvv.vv (vv.vv: Main firmware version)
i BLD bbbb (bbbb: Main firmware build number)
i DRV d.dd (d.dd: CD drive firmware version)
i DEC eeee (eeee: Decoder ROM version)
i L nnnnnn (nnnnnn: Decoder firmware version)
③ The firmware version number display is exited when the
unit is turned OF
2) Total drive run time check
This display shows the total run time count of the CD drive
NOTE
Since the EEPROM on the front PCB stores various total run time data,
the total drive run time is cleared when the front PCB is replaced.
① Then while pressing and holding both the STOP and PLAY/
PAUSE buttons on the main unit, press the POWER switch
to turn the unit on.
NOTE
Continue holding down the STOP and PLAY/PAUSE buttons until
“RUN TIME” is displayed.
② “RH” is displayed together with the total CD drive run time
count. (Units : hour)
The total CD drive run time is cleared when “1. [4] EEPROM
initialization (For use in factory)” is performed in the test
mode.
③ The total CD drive run time display is exited when the unit is
turned OFF.
3. Firmware update
1) Confirmation of firmware version
Before starting a firmware update, check the firmware version of the
CD-200SB that you are using.
① Turn the unit off and remove the SD card and USB flash
drive. Then, while pressing and holding both the STOP
and REPEAT buttons on the main unit, press the POWER
switch to turn the unit on.
NOTE
Even after WELCOME appears on the display, keep pressing the STOP
and REPEAT buttons until VERSION appears.
② Check the following information items by using the FOLDER g/t buttons to change the item shown.
i VERvv.vv (vv.vv: Main firmware version)
i BLD bbbb (bbbb: Main firmware build number)
i DRV d.dd (d.dd: CD drive firmware version)
i DEC eeee (eeee: Decoder ROM version)
i L nnnnnn (nnnnnn: Decoder firmware version)
If the “Main firmware version,” “Main firmware build number” and
“Decoder firmware version” shown here are the same or newer than
the firmware versions that you were planning to use for the update,
there is no need to update the firmware.
NOTE
The “CD drive firmware version” and “Decoder ROM version”
are not used when updating other firmware.
2) Prepare the update media
① Download the latest firmware from the TASCAM website
(http://tascam.com/) and open the compressed file.
② Copy the downloaded firmware to the root folder (highest
level folder) on an SD card or USB flash drive
3) Main firmware update procedures
① Turn the unit off and remove the SD card and USB flash
drive. Then, while pressing and holding both the DISPLAY
and OPEN/CLOSE buttons on the main unit, press the
POWER switch to turn the unit on.
NOTE
Even after WELCOME appears on the display, keep pressing the
DISPLAY and OPEN/CLOSE buttons until -UPDATE appears. When
you release the buttons after -UPDATE appears on the display, -NO
DATA will appear on the display.
② Insert the update media that you prepared into the SD card
slot or USB port. After the unit verifies the update media
and main firmware updater file, UPDATE? appears on the
display.
③ Press the DISPLAY button on the main unit. -ERASE and
-WRITE will appear on the display and the update will be
executed.
④ When updating completes, -FINISH will appear on the
display.
⑤ Press the POWER switch on the main unit to turn it off.
⑥ Confirm that the “Main firmware version” and “Main firmware build number” are the latest. (Refer to “Checking the
firmware versions” above.)
This completes the update of the main firmware.
4) Decoder firmware update procedures
① Turn the unit off and remove the SD card and USB flash
drive. Then, while pressing and holding both the DISPLAY
and FOLDER/TRACK SELECT 5 buttons on the main unit,
press the POWER switch to turn the unit on.
NOTE
Even after WELCOME appears on the display, keep pressing the
DISPLAY and FOLDER/TRACK SELECT 5 buttons until -IPL WRT
appears. When you release the buttons after -IPL WRT appears on the
display, -SETFILE will appear on the display.
② Insert the update media that you prepared into the SD card
slot or USB port.
After the unit verifies the update media and decoder
firmware updater file, -WRITING appears on the display and
updating starts automatically.
③ When updating completes, -DONE will appear on the display.
④ Press the POWER switch on the main unit to turn it off.
⑤ Confirm that the “Decoder firmware version” is the latest.
(Refer to “Checking the firmware versions” above.)
This completes the update of the decoder firmware.
Block Diagram
Exploded Views and Parts List
1977223A51 CD-5020-A51 1
2 E0140770 POWER CORD,JPN PSE 7A G (JPN) 1 V
E0172550 POWER CORD,KOREA WS-006A (KOR) 1 V
3E000360 POWER CORD,AUS G (AUS) 1 V
3E015210 POWER CORD,EUR-G (EUR) 1 V
E0148200 POWER CORD,CQ-5818-00 G (CHI) 1 V
E0156970 POWER CORD,TM 7A BSMI G (TM) 1 V
3E009230 POWER CORD,UL/CSA SPEI-G (EXT) 1 V
3 3E0394800A TRANS100/120/230 CDP1260G 1 V
4 3M000870 CABL BAND,100MM DS-8432-G 8
5 3M000880 BUSHING, #2271(CSA)-G 1
6 3M001950 FOOT,21MM G 4
7 3M0131000A @NUT, M12X2.3 G 1
8 3M0134900A BADGE TASCAM SILVER G 1
9 3M0173600A HARNES WL3-52T7.5*3.3*52G 3
10 3M0189400C BONNET CD-30 G 1
11 3M0191300B BRACKET,TRANS 1
12 3M0195700A SNAP RIVET(SR3-3.5) X-9G 2
13 M01334900A ESCUTCHEON,POWERCD-RW402G 1
14 M01335100B BUTTON,POWER CD-RW402 G 1
15 M01891300B KNOB,VOLUME MCD1G 1
16 M02481300C BUTTON,OPE CD-160MK2 G 1
17 M02481630A CHASSIS,MAIN CD-200SB G 1
18 M02496600A BUTTON,B CD-160MK2 G 1
19 M02497200A ANGLE,R CD-160MK2 G 1
20 M02497300A ANGLE,L CD-160MK2 G 1
21 M02692700A FIBER WSHR,10*3.2*0.8TBLK 6
22 M02947700B BRACKET,DRIVE CD-200 G 1
23 M02947900A PANEL,TRAY CD-200 G 1
24 M02948100B SHIELD PLATE,PWR CD-200 G 1
25 M02954720A COVER,SD CD-200SB G 1
26 M03007000A FRAME,BOTTOM CD-200 G 1
27 M03026300A WASHER,PC 10*3.2*1.0 G 1
28 M03045910A WINDOW,CD-200SB G 1
29 M03473800A PANEL.REAR DM CD-200SB G (JPN,KOR,AUS,EUR,CHI) 1
M03473893B PANEL,REAR ETC CD-200SB G (EXT) 1
30 M03473900C PANEL,FRONT CD-200SB G 1
31 M03474000A HOLDER,COVER CD-200SB G 1
32 M03474100A BUTTON.TEN KEY CD-200SB G 2
33 M03474200A BUTTON,A CD-200SB G 1
34 M03474300A BUTTON,B CD-200SB G 1
35 M03474400A BUTTON,C CD-200SB G 1
36 M03492900A PLATE,EARTH CD200SB G (PCBA,BAL CD-200SB G) 1
37 M03495300A BRKT,PH JACK CD200SB G 1
38 Y00450000A AC SELECT ASSY,CDA550 G (EXT)
50 E95361800A PCB ASSY,PW-SW CD200 G 1 Refer to page 24 (GATHER PCBA,FRT CD200SB G)
51 E95361910A PCBA,PHONE CD200SB G 1 Refer to page 26 (GATHER PCB,AN CD200SB G (2))
52 E95423910A PCB ASSY,BAL CD-200SB G 1 Refer to page 28 (GATHER PCB,BAL IO MD02G)
53 E95462500A PCBA,FRONTMAIN CD200SB G 1 Refer to page 24 (GATHER PCBA,FRT CD200SB G)
54 E95464400A PCBA,ANALOG CD200SB G 1 Refer to page 25 (GATHER PCB,AN CD200SB G (1))
55 E95464500A PCBA,USBSDAUD CD200SB G 1 Refer to page 27 (GATHER PCB,SWUSB G)
56 E95464600A PCBA,10KEY CD200SB G 1 Refer to page 27 (GATHER PCB,SWUSB G)
57 E95377300A PCB ASSY,TRA CD200I JPN G (JPN) 1 Refer to page 26 (GATHER PCB,AN CD200SB G (2))
E95377320A PCB ASSY,TRA CD200I T/C G (EXT) 1 Refer to page 26 (GATHER PCB,AN CD200SB G (2))
E95377330A PCB ASSY,TRA CD200I TM G (TM) 1 Refer to page 26 (GATHER PCB,AN CD200SB G (2))
E95377350A PCB ASSY,TRA CD200I EUR G (KOR,AUS,EUR,CHI) 1 Refer to page 26 (GATHER PCB,AN CD200SB G (2))
60 E01865400A HARN ASSY,CDAO CD200SB G 1 Refer to page 28 (WIRE Section)
61 E01865500A HARN ASSY,CTRLA CD200SB G 1 Refer to page 28 (WIRE Section)
62 E01865600A HARN ASSY,CTRLB CD200SB G 1 Refer to page 28 (WIRE Section)
63 E01865700A HARN ASSY,10KEY CD200SB G 1 Refer to page 28 (WIRE Section)
64 E01554400C HARNESS ASSY,DR CD200 G 1 Refer to page 28 (WIRE Section)
100 3B0701908A SCREW BTT-SSB 4*8 2
101 B00170608A SCREW,VPCR 3*8 FZB G 1
102 B00171406A SCREW,BPA 3*6 FZB G 3
103 B00197606A SCREW,PPSU 3*6 FZB G 4
104 B00197612A SCREW,PPSU 3*12 FZB G 2
105 B00197806A SCREW,PPSU 3*6 FZC G 4
106 B001978068 SCREW,PPSU 3*8 FZC G 6
107 B00199008A SCREW,BPP 3*8 FZC G 15
108 B00199706A SCREW,BPB 3*6 FZB G 15
109 B00199708A SCREW,BPB 3*8 FZB G 13
110 B00199808A SCREW,BPB 4*8 FZB G (EXT) 2
111 B00208807A SCREW,FPS 3*7 FZB G 8
112 B00208908A SCREW,PPPU 3*8 FZB G
PC Boards and Parts List
REF.NO. PARTS NO. DESCRIPTION .
(E95464100A) GATHER PCBA,FRT CD200SB G
(E95464154A) GA PCBA,FRT CD200SB CHI G For China
E95462500A PCBA,FRONTMAIN CD200SB G
PCBA,A-FRTMAIN CD200SB G
W1 E0123241 JUMPER WIRE,5MM G
W2 E0123331 JUMPER WIRE,12.5MM G
W3 E0123301 JUMPER WIRE,10MM G
W4 E0123271 JUMPER WIRE,7.5MM G
W5 E0123331 JUMPER WIRE,12.5MM G
W6 E0123271 JUMPER WIRE,7.5MM G
W7 E0123271 JUMPER WIRE,7.5MM G
W8 E0123241 JUMPER WIRE,5MM G
W9 E0123241 JUMPER WIRE,5MM G
W10 E0123241 JUMPER WIRE,5MM G
W11 E0123241 JUMPER WIRE,5MM G
W12 E0123301 JUMPER WIRE,10MM G
W13 E0123271 JUMPER WIRE,7.5MM G
W14 E0123271 JUMPER WIRE,7.5MM G
W15 E0123271 JUMPER WIRE,7.5MM G
W16 E0123271 JUMPER WIRE,7.5MM G
W17 E0123241 JUMPER WIRE,5MM G
W18 E0123241 JUMPER WIRE,5MM G
W19 E0123271 JUMPER WIRE,7.5MM G
W20 E0123241 JUMPER WIRE,5MM G
W21 E0123301 JUMPER WIRE,10MM G
W22 E0123241 JUMPER WIRE,5MM G
W23 E0123271 JUMPER WIRE,7.5MM G
W24 E0123271 JUMPER WIRE,7.5MM G
W25 E0123271 JUMPER WIRE,7.5MM G
W26 E0123301 JUMPER WIRE,10MM G
W28 E0123271 JUMPER WIRE,7.5MM G
W29 E0123271 JUMPER WIRE,7.5MM G
W30 E0123271 JUMPER WIRE,7.5MM G
W31 E0123271 JUMPER WIRE,7.5MM G
W32 E0123271 JUMPER WIRE,7.5MM G
W33 E0123241 JUMPER WIRE,5MM G
W34 E0123271 JUMPER WIRE,7.5MM G
W35 E0123301 JUMPER WIRE,10MM G
W36 E0123301 JUMPER WIRE,10MM G
W37 E0123271 JUMPER WIRE,7.5MM G
W38 E0123301 JUMPER WIRE,10MM G
W39 E0123301 JUMPER WIRE,10MM G
PCBA,T-FRTMAIN CD200SB G
U100 S0095323 IC,R5F2L38ACNFA G
LCD100 E01865200B LCD,CD-200SB G
U102 E01568800A LCD HOLDER,CD-P1260
U106 S0095420 IC,RPM7238-H8R G
C110 C0093722 CE,SV 16V 100UFM H5 TP25G
C122 C0093722 CE,SV 16V 100UFM H5 TP25G
J100 E0101924 CONNECTOR,B 3B-PH-SM4(LF)
J101 E0101934 CONNECTOR,B4B-PH-SM4(LF) G
J105 E0101964 CONNECTOR,B7B-PH-SM4(LF) G
J106 E0101974 CONNECTOR,B8B-PH-SM4(LF)G
J107 E0101994 CONNECTOR,B10B-PH-SM4(LF)
J108 E0102004 CONNECTOR,B11B-PH-SM4(LF)
J110 E0101984 CONNECTOR,B 9B-PH-SM4(LF)
RA102 R0204032 RES ARRAY,RKL4ADTPA4702F G
REF.NO. PARTS NO. DESCRIPTION .
SW100 E0127100 SW,TACT SKHHAM2520 G
SW101 E0127100 SW,TACT SKHHAM2520 G
SW102 E0127100 SW,TACT SKHHAM2520 G
SW103 E0127100 SW,TACT SKHHAM2520 G
SW104 E0127100 SW,TACT SKHHAM2520 G
SW105 E0127100 SW,TACT SKHHAM2520 G
SW106 E0127100 SW,TACT SKHHAM2520 G
SW107 E0127100 SW,TACT SKHHAM2520 G
SW108 E0127100 SW,TACT SKHHAM2520 G
SW109 E0127100 SW,TACT SKHHAM2520 G
U100 E01865300B CPU ASSY,CONT CD-200SB G
E95361800A PCB ASSY,PW-SW CD200 G
PCB ASSY,PW-SW CD200 G
C40 E0122630 SPK KILLER,CS12-F2GA472MYAS G V
P40 E0112450 CONNECTOR,B2P3VH(LF)(SN) G V
SW40 E0128290 SW,SFDLB11L7U-TK-G V
GATHER PCBA,FRT CD200SB G
フロントメイン基板
TASCAM CD-200SB
– 25 –
CAUTION Part with numbers in parentheses ( ) cannot be ordered. If you want to order service parts, be sure
to use “Child” part numbers (numbers in Bold), which refer to individual parts of a parent part.
注 意 “( )” 付き品番は、発注できません。補修部品を発注する際は、太字品番で発注してください。
GATHER PCB,AN CD200SB G (1)
アナログ基板 (1)
REF.NO. PARTS NO. DESCRIPTION .
(E95464200A) GA PCBA,AN CD200SB DM G [ J ]
(E95464220A) GA PCBA,AN CD200SB TC G [ US/C ]
(E95464230A) GA PCBA,AN CD200SB TM G [ T ]
(E95464250A) GA PCBA,AN CD200SB EUR G [ E ]
(E95464254A) GA PCBA,AN CD200SB CHI G [ CH ]
E95464400A PCBA,ANALOG CD200SB G
PCBA,A-ANALOG CD200SB G
D201 S0067021 @DIODE,1SS133 T-77 G
D202 S0067021 @DIODE,1SS133 T-77 G
D203 S0067021 @DIODE,1SS133 T-77 G
D204 S0067021 @DIODE,1SS133 T-77 G
D205 S0067021 @DIODE,1SS133 T-77 G
D209 S0068711 @DIODE,RB441Q40 T-77 G
D215 S0068711 @DIODE,RB441Q40 T-77 G
D218 S0068711 @DIODE,RB441Q40 T-77 G
W201 E0123301 JUMPER WIRE,10MM G
W203 E0123301 JUMPER WIRE,10MM G
W204 E0123271 JUMPER WIRE,7.5MM G
W205 E0123301 JUMPER WIRE,10MM G
W206 E0123301 JUMPER WIRE,10MM G
W207 E0123301 JUMPER WIRE,10MM G
W208 E0123301 JUMPER WIRE,10MM G
W209 E0123301 JUMPER WIRE,10MM G
W210 E0123241 JUMPER WIRE,5MM G
W211 E0123241 JUMPER WIRE,5MM G
W212 E0123241 JUMPER WIRE,5MM G
W213 E0123271 JUMPER WIRE,7.5MM G
W214 E0123301 JUMPER WIRE,10MM G
W215 E0123241 JUMPER WIRE,5MM G
W216 E0123271 JUMPER WIRE,7.5MM G
W217 E0123301 JUMPER WIRE,10MM G
W218 E0123301 JUMPER WIRE,10MM G
W219 E0123301 JUMPER WIRE,10MM G
W220 E0123271 JUMPER WIRE,7.5MM G
W221 E0123301 JUMPER WIRE,10MM G
W223 E0123241 JUMPER WIRE,5MM G
W224 E0123241 JUMPER WIRE,5MM G
W225 E0123271 JUMPER WIRE,7.5MM G
W226 E0123301 JUMPER WIRE,10MM G
W227 E0123301 JUMPER WIRE,10MM G
W228 E0123241 JUMPER WIRE,5MM G
W229 E0123301 JUMPER WIRE,10MM G
W230 E0123271 JUMPER WIRE,7.5MM G
W231 E0123271 JUMPER WIRE,7.5MM G
W232 E0123241 JUMPER WIRE,5MM G
W233 E0123241 JUMPER WIRE,5MM G
W234 E0123271 JUMPER WIRE,7.5MM G
W235 E0123271 JUMPER WIRE,7.5MM G
W236 E0123301 JUMPER WIRE,10MM G
W237 E0123241 JUMPER WIRE,5MM G
W238 E0123301 JUMPER WIRE,10MM G
W239 E0123301 JUMPER WIRE,10MM G
W240 E0123301 JUMPER WIRE,10MM G
W241 E0123301 JUMPER WIRE,10MM G
W242 E0123301 JUMPER WIRE,10MM G
W243 E0123301 JUMPER WIRE,10MM G
W245 E0123301 JUMPER WIRE,10MM G
W247 E0123301 JUMPER WIRE,10MM G
REF.NO. PARTS NO. DESCRIPTION .
W248 E0123271 JUMPER WIRE,7.5MM G
W249 E0123271 JUMPER WIRE,7.5MM G
W250 E0123241 JUMPER WIRE,5MM G
W251 E0123271 JUMPER WIRE,7.5MM G
W252 E0123271 JUMPER WIRE,7.5MM G
W253 E0123301 JUMPER WIRE,10MM G
W254 E0123271 JUMPER WIRE,7.5MM G
W255 E0123271 JUMPER WIRE,7.5MM G
W256 E0123301 JUMPER WIRE,10MM G
W257 E0123271 JUMPER WIRE,7.5MM G
W258 E0123301 JUMPER WIRE,10MM G
W259 E0123301 JUMPER WIRE,10MM G
W260 E0123301 JUMPER WIRE,10MM G
W261 E0123241 JUMPER WIRE,5MM G
W262 E0123271 JUMPER WIRE,7.5MM G
W263 E0123271 JUMPER WIRE,7.5MM G
F200 E0123301 JUMPER WIRE,10MM G
F201 E0123301 JUMPER WIRE,10MM G
W265 E0123301 JUMPER WIRE,10MM G
W266 E0123301 JUMPER WIRE,10MM G
L200 E0123241 JUMPER WIRE,5MM G
L203 E0123241 JUMPER WIRE,5MM G
W268 E0123241 JUMPER WIRE,5MM G
W271 E0123271 JUMPER WIRE,7.5MM G
W273 E0123301 JUMPER WIRE,10MM G
W301 E0123271 JUMPER WIRE,7.5MM G
W302 E0123241 JUMPER WIRE,5MM G
W303 E0123241 JUMPER WIRE,5MM G
W304 E0123271 JUMPER WIRE,7.5MM G
W305 E0123301 JUMPER WIRE,10MM G
PCBA,R-ANALOG CD200SB G
L201 E0126520 FILTER,DSS6NB32A101Q91A G
Q200 S0074832 TRANSISTOR,KTC2874BAT/PG
Q201 S0094402 TRANSISTOR,DTA124ESA G
Q202 S0094422 TRANSISTOR,DTC124ESA G
Q203 S0094422 TRANSISTOR,DTC124ESA G
Q204 S0074832 TRANSISTOR,KTC2874BAT/PG
PCBA,T-ANALOG CD200SB G
U200 S0044584 IC,HD74LV04AFPEL(14P)
U201 S0065814 IC,AK4384ET G
U202 S0044970 IC,NJM4580L
U209 E0130730 OPT CONN,GP1FAV51TK0F GZ0
U211 S0082972 IC,BD9702CP-V5 G
U212 S0069960 IC,BA05CC0T G
U214 S0091610 @IC,KIA1117PI33-CU/P G
U215 S0065050 IC,NJM7808FA-#ZZZSB G
U216 S0065060 IC,NJM7908FA G
D206 S0066810 DIODE,MUR420G G
J200 E01555100C HARNESS ASSY,PHONE CD200G
J201 E01865800B HARN ASSY,DAOUT CD200SB G
J203 E01554200C HARNESS ASSY,DAC CD200 G
J206 E0125830 JACK PIN 2P HSP-252V304-G
J207 E0156810 JACK,YKC 21-3486N G
J208 E01596700B HARN ASSY,PW CD200I G
CAUTION Part with numbers in parentheses ( ) cannot be ordered. If you want to order service parts, be sure
to use “Child” part numbers (numbers in Bold), which refer to individual parts of a parent part.
注 意 “( )” 付き品番は、発注できません。補修部品を発注する際は、太字品番で発注してください。
TASCAM CD-200SB
– 26 –
REF.NO. PARTS NO. DESCRIPTION .
J209 E01553700B HARNESS ASSY,F-PW CD200 G
J210 E0156820 CONNECTOR,B 5B-EHA(LF) G
J212 E01555400C HARNESS ASSY,DPW CD200 G
J213 E01865900A HARN ASSY,PW10K CD200SB G
J301 E0119790 CONNECTOR,B 8B-PH-K-S G
C200 C00867400A CE,GS 25V 3300UF M 16*25G V
C0077280 !CE,GS 25V3300UF M G V
C0087690 !CE,GS 25V 3300UF M G V
C0093160 CE,SK 25V 3300UF M G V
C264 C00867202A CE,GS 25V 1000UF M 10*20TP G V
C0077252 !CE,GS 25V1000UF M TP G V
C0087672 !CE,GS 25V 1000UF M TP G V
C0093102 CE,SK 25V 1000UF M TP G V
C269 C00867202A CE,GS 25V 1000UF M 10*20TP G V
C0077252 !CE,GS 25V1000UF M TP G V
C0087672 !CE,GS 25V 1000UF M TP G V
C0093102 CE,SK 25V 1000UF M TP G V
L202 E0130740 COIL,10UH 3.6A DR2W8*7 G
L204 E0157480 FILTER,FER K5A-RH35*0.8 G
L205 E0157480 FILTER,FER K5A-RH35*0.8 G
FG1 E0123470 TERMINAL,GND-8 G
FG2 E0123470 TERMINAL,GND-8 G
FG3 E0123470 TERMINAL,GND-8 G
FG4 E0123470 TERMINAL,GND-8 G
L206 E0162680 FILTER,BL02RN1R2M2B G
L207 E0160301 FLTR,BL01RN1A1E1A G
D207 S0071811 DI,1N4003-F TAPINGW=52 G V
D208 S0071811 DI,1N4003-F TAPINGW=52 G V
D210 S0071811 DI,1N4003-F TAPINGW=52 G V
D211 S0071811 DI,1N4003-F TAPINGW=52 G V
D213 S0071811 DI,1N4003-F TAPINGW=52 G V
D214 S0071811 DI,1N4003-F TAPINGW=52 G V
D216 S0071811 DI,1N4003-F TAPINGW=52 G V
D217 S0071811 DI,1N4003-F TAPINGW=52 G V
Q205 E0123241 JUMPER WIRE,5MM G
Q206 E0123241 JUMPER WIRE,5MM G
E95377300A PCB ASSY,TRA CD200I JPN G [ J ]
E95377320A PCB ASSY,TRA CD200I T/C G [ US/C ]
E95377330A PCB ASSY,TRA CD200I TM G [ T ]
E95377350A PCB ASSY,TRA CD200I EUR G [ E ]
PCB ASSY,T-TRA JP CD200G [ J ]
PCB ASSY,T-TRA CD200G T/C [ US/C ]
PCB ASSY,T-TRA CD200G TM [ T ]
PCB ASSY,T-TRA CD200G EUR [ E ]
F1 E0108150 T-LAG FUSE,1.25A218MXPGN0 V
(F1) E0126350 HOLDER,FUSE HOLDER 5.0 G V
(F1) E0126350 HOLDER,FUSE HOLDER 5.0 G V
J2 E01555300C HARNESS ASSY,TPW CD200 G
J3 E01554800C HARNESS ASSY,PSW CD200 G
L1 E0156850 FILTER,AC LINE LFH-601U G V
J1 E0178160 TERMINAL,LAPPING 2P G V
REF.NO. PARTS NO. DESCRIPTION .
E95361910A PCBA,PHONE CD200SB G
PCB ASSY,A-PHONE CD200 G
W803 E0123241 JUMPER WIRE,5MM G
W805 E0123241 JUMPER WIRE,5MM G
W806 E0123271 JUMPER WIRE,7.5MM G
PCB ASSY,R-PHONE CD200 G
Q70 S0074832 TRANSISTOR,KTC2874BAT/PG
Q71 S0074832 TRANSISTOR,KTC2874BAT/PG
PCBA,T-PHONE CD200SB G
U70 S0067650 IC,NJM4580D G
J70 E0073670 JACK,JY-6313-01-030 G
J71 E0113730 CONNECTOR,S 7B-PH-K-S G
VR70 R0155900 VAR RES,RK09K12A-20KAG
GATHER PCB,AN CD200SB G (2)
アナログ基板 (2)
TASCAM CD-200SB
– 27 –
CAUTION Part with numbers in parentheses ( ) cannot be ordered. If you want to order service parts, be sure
to use “Child” part numbers (numbers in Bold), which refer to individual parts of a parent part.
注 意 “( )” 付き品番は、発注できません。補修部品を発注する際は、太字品番で発注してください。
REF.NO. PARTS NO. DESCRIPTION .
(E95464300A) GATHER PCBA,SWUSB G
(E95464354A) GA PCBA,SWUSB CHI G For China
E95464500A PCBA,USBSDAUD CD200SB G
PCBA,S-USBSDAUD CD200SB G
U202 S0092594 IC,RP111H181D G
U203 S0095384 IC,BU94702AKV-E2 G
U204 S0048794 IC,SN74LV157ANSR G
U205 S0067954 IC,SN74LVC2G157DCTR GAX
U206 S0095394 IC,AK4104ET G
U207 S0079754 IC,AIC1526-0GSTR G
U208 S00956300C IC ROM ASSY,USBAUDIO G
U208 S0091974 IC,MX25L4006EM1I-12G G
D203 S0022094 DIODE,1SS355
J201 E0101954 CONNECTOR,B6B-PH-SM4(LF) G
J202 E0100024G CONNE,P B7BPH-SM4RED(LF)G
J203 E0101974 CONNECTOR,B8B-PH-SM4(LF)G
J204 E0102004 CONNECTOR,B11B-PH-SM4(LF)
L201 E0126164 BEAD COIL,BLM18PG471SN1D G
L202 E0126164 BEAD COIL,BLM18PG471SN1D G
L205 E0126164 BEAD COIL,BLM18PG471SN1D G
L206 E0070874 BEAD COIL.BLM18BD601SN1 G
L207 E0070874 BEAD COIL.BLM18BD601SN1 G
L208 E0070874 BEAD COIL.BLM18BD601SN1 G
L209 E0070874 BEAD COIL.BLM18BD601SN1 G
L210 R0157394 RD,1/10W 0 OHM J0603G
L211 R0157394 RD,1/10W 0 OHM J0603G
L212 E0070874 BEAD COIL.BLM18BD601SN1 G
P206 E0172303 CONNECTOR,SCDA7A0200 G
T200 E0166304 FILTER,NT2012 985BH1007 G
X101 E0141094 RESONATOR,SEG55 16.9344 G
PCBA,T-USBSDAUD CD200SB G
J200 E01746400A HARN ASSY,GND RCHS32 G
J205 E0102490 CONNECTOR,B 8B-EH(LF)(SN)
P204 E0141212 CONNECTOR,UBA-4R-D14T-4D G
E95464600A PCBA,10KEY CD200SB G
PCBA,S-10KEY CD200SB G
U301 S0065394 IC,SN74LV595APWR G
U302 S0065394 IC,SN74LV595APWR G
D301 S0084614 LED,SML-D12D8WT86Q G
D302 S0084614 LED,SML-D12D8WT86Q G
D303 S0084614 LED,SML-D12D8WT86Q G
D304 S0084614 LED,SML-D12D8WT86Q G
D305 S0084614 LED,SML-D12D8WT86Q G
D306 S0084614 LED,SML-D12D8WT86Q G
D307 S0084614 LED,SML-D12D8WT86Q G
D308 S0079854 LED,SML-012V8TT86 RED G
D309 S0084614 LED,SML-D12D8WT86Q G
D310 S0084614 LED,SML-D12D8WT86Q G
D311 S0084614 LED,SML-D12D8WT86Q G
D312 S0084614 LED,SML-D12D8WT86Q G
D313 S0084614 LED,SML-D12D8WT86Q G
D314 S0084614 LED,SML-D12D8WT86Q G
D315 S0084614 LED,SML-D12D8WT86Q G
REF.NO. PARTS NO. DESCRIPTION .
D316 S0084614 LED,SML-D12D8WT86Q G
J301 E0101914 CONNECTOR,B 2B-PH-SM4(LF)
J302 E0101984 CONNECTOR,B 9B-PH-SM4(LF)
SW301 E0186094 SW,TACT SFKHHMM2520T G
SW302 E0186094 SW,TACT SFKHHMM2520T G
SW303 E0186094 SW,TACT SFKHHMM2520T G
SW304 E0186094 SW,TACT SFKHHMM2520T G
SW305 E0186094 SW,TACT SFKHHMM2520T G
SW306 E0186094 SW,TACT SFKHHMM2520T G
SW307 E0186094 SW,TACT SFKHHMM2520T G
SW308 E0186094 SW,TACT SFKHHMM2520T G
SW309 E0186094 SW,TACT SFKHHMM2520T G
SW310 E0186094 SW,TACT SFKHHMM2520T G
SW311 E0186094 SW,TACT SFKHHMM2520T G
SW312 E0186094 SW,TACT SFKHHMM2520T G
SW313 E0186094 SW,TACT SFKHHMM2520T G
SW314 E0186094 SW,TACT SFKHHMM2520T G
SW315 E0186094 SW,TACT SFKHHMM2520T G
SW316 E0186094 SW,TACT SFKHHMM2520T G
SW317 E0186094 SW,TACT SFKHHMM2520T G
GATHER PCB,SWUSB G
スイッチ ・USB 基板
CAUTION Part with numbers in parentheses ( ) cannot be ordered. If you want to order service parts, be sure
to use “Child” part numbers (numbers in Bold), which refer to individual parts of a parent part.
注 意 “( )” 付き品番は、発注できません。補修部品を発注する際は、太字品番で発注してください。
TASCAM CD-200SB
– 28 –
REF.NO. PARTS NO. DESCRIPTION .
(E95423810A) GATHER PCBA,BAL CD200SB G
(E95423855A) GA PCBA,BAL CD200SB CHI G For China
E95423910A PCB ASSY,BAL CD-200SB G
PCB ASSY,A-BAL CD-200IB G
D101 D201 S0067021 @DIODE,1SS133 T-77 G
D102 D202 S0067021 @DIODE,1SS133 T-77 G
D103 D203 S0067021 @DIODE,1SS133 T-77 G
D104 D204 S0067021 @DIODE,1SS133 T-77 G
W101 E0123241 JUMPER WIRE,5MM G
W102 E0123301 JUMPER WIRE,10MM G
W104 E0123301 JUMPER WIRE,10MM G
W105 E0123301 JUMPER WIRE,10MM G
W106 E0123241 JUMPER WIRE,5MM G
W107 E0123301 JUMPER WIRE,10MM G
W108 E0123301 JUMPER WIRE,10MM G
W109 E0123241 JUMPER WIRE,5MM G
W110 E0123301 JUMPER WIRE,10MM G
W111 E0123241 JUMPER WIRE,5MM G
W112 E0123241 JUMPER WIRE,5MM G
PCB ASSY,R-BAL CD-200IB G
Q101 Q201 S0074832 TRANSISTOR,KTC2874BAT/PG
Q102 Q202 S0074832 TRANSISTOR,KTC2874BAT/PG
L105 L205 E0127040 BEAD COIL,FBR07HA850SB00G
L108 L208 E0127040 BEAD COIL,FBR07HA850SB00G
PCB ASSY,T-BAL CD-200SB G
U102 U202 S0067650 IC,NJM4580D G
P101 P201 E0123150 PLUG,XLR M JY-5032A-030 G
P102+P103 E01760800A HARN ASSY,BAL CD-200IB G
REF.NO. PARTS NO. DESCRIPTION .
E01865400A HARN ASSY,CDAO CD200SB G
E01865500A HARN ASSY,CTRLA CD200SB G
E01865600A HARN ASSY,CTRLB CD200SB G
E01865700A HARN ASSY,10KEY CD200SB G
E01554400C HARNESS ASSY,DR CD200 G
9. Included Accessories
NOTES 注意
0PC boards shown are viewed from parts side.
0Parts marked with * require longer delivery time.
0The parts with no reference number or no parts
number in the exploded views are not supplied.
0As regards the resistors and capacitors, refer to the
circuit diagrams contained in this manual.
0V Parts marked with this sign are safety critical
components. They must be replaced with identical
components – refer to the appropriate parts list
and ensure exact replacement.
0Parts of [ ] mark can be used only with the version
designated.
[ J ] : JAPAN [ US/C ] : U.S.A./CANADA [ K ] : KOREA
[ E ] : EUROPE [ UK ] : U.K. [ JEX ] : JAPAN & ASIA
[ A ] : AUSTRALIA [ T ] :TAIWAN
[ CH ] : CHINA [ ETC ] : U.S.A./CANADA/South Americ
Documents / Resources
 | CD200SB CD Solid State Player |
References
- User Manualmanual.tools