Tungsten Manuals / Datasheets / Instructions

ABT B0CZ9VFQ2P Kindle Scribe 16GB with Premium Pen in Tungsten Instructions

Discover the comprehensive user manual for the B0CZ9VFQ2P Kindle Scribe 16GB with Premium Pen in Tungsten. Access instructions and details on utilizing the Premium Pen in Tungsten with the Scribe 16GB device.

BROMIC TUNGSTEN Smart Heat Portable Heater Instruction Manual

BROMIC TUNGSTEN Smart Heat Portable Heater Safety Information WARNING Do not store or use petrol or other flamable vapor and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. DANGER If you smell gas: Shut off gas to the appliance Extinguish any open flame If odour continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING: For Outdoor Use Only. This appliance shall not be installed or used indoors. This manual contains important information about the assembly, operation, and maintenance of TUNGSTEN Smart-Heat™ Heaters. Please pay close attention to the important safety information shown throughout this instruction manual. Any safety information will be accompanied by the following safety alert symbols: DANGER, WARNING, IMPORTANT READ THIS MANUAL CAREFULLY before installing or servicing this product Service and repair must only be done by a qualified service person. The heater should be inspected before use and at least annually by a qualified service person. Improper installation, operation, or maintenance can result indeath, severe injury, or property damage. This manual must be kept following installation for future reference. IMPORTANT NOTES AND WARNINGS WARNING Failure to follow the warnings and instructions in this manual could result in severe personal injury, death or property damage. This appliance must be used only in an outdoor area and shall not be used in a building, garage or any other enclosed area. This appliance must not be installed or used indoors. Do not place articles on or against this appliance. Any guard or other protective device removed for servicing (conducted by an authorised person) must be replaced before operating the heater. The base of the appliance must be filled with sand as shown later in these instructions. Do not operate this appliance unless the base is filled with sand. The hose assembly is not to be located in areas where the hose may be subject to accidental damage. Remove transit protection before use. Turn off the gas cylinder valve immediately if smell of gas is detected. Do not transport or move the heater while it is operating. The heater should be inspected before use and at least annually by a qualified service person. Do not use or store flammable materials near this appliance Do not spray aerosols or flammable materials in the vacinity of this appliance while it is in operation Any guard or other protective device removed for servicing (conducted by an authorised person) must be replaced before operating the heater. Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Children should be carefully supervised when they are in the area of the heater. Clothing or other flammable materials should not be hung from the heater or placed on or near the heater. Do not perform maintenance until heater has been turned off, and heater temperature has cooled to room temperature. Do not expose the burner to water or moisture. The appliance must be protected from rain. Do not use the heater if any of these parts are exposed to water until the appliance is inspected or repaired by an authorised service person. The installer is to ensure that the requirements of the local authority, local gas fitting regulations, municipal building codes, and any other relevant statutory regulations are carried out. Certain materials or items, when stored under or near the appliance, will be subjected to radiant heat and could be seriously damaged. The whole gas system, hose assembly, regulator, pipes, and burner should be inspected for damage and leaks before each use and at least annually by an authorized person for the life of the heater. The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of excessive abrasion or wear, or if the hose is damaged. The replacement hose must be purchased from Bromic Heating Pty Ltd. All leak tests should be done with a soap solution. Never use an open flame to check for leaks. Do not use the heater until all connections have been leak tested. This radiant heater is NOT intended to be installed on recreational vehicles and/or boats. Improper installation, adjustment, or alteration can cause personal injury, property damage, or even death. Do not attempt to alter the unit in any manner. Do not paint any surface of the heater or top canopy reflector. Burner and circulation air passageways of the heater must be kept clean. Frequent cleaning may be required as necessary. Turn Gas Supply off when not in use. Check the heater immediately if any of the following occurs: The heater does not reach temperature. The burner makes popping noise during use (a slight noise is normal when the burner is ignited or extinguished). This appliance is not intended for use by young or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely. Check for damage to the appliance regularly. If damage to the appliance is suspected, discontinue use immediately and contact the supplier or qualified person for repair. Avoid inhaling fumes emitted from the heater’s first use. Smoke and odour from the burning of oils used in manufacturing will appear. Both the smoke and odour will dissipate after approximately 30 minutes. The pressure regulator and hose assembly supplied with the appliance must be used. Replacement regulator and hose assemblies must be purchased from Bromic Heating Pty Ltd. Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance. A cylinder must be stored outdoors in a well-ventilated area out of the reach of children. A disconnected cylinder must have dust caps tightly installed and must not be stored in a building, garage or any other enclosed area. Do not store a spare LP-gas cylinder under or near this appliance; Never fill the cylinder beyond 80% full The heater head angle slip pin must be inserted if transporting the heater to ensure no damage during transit. PRODUCT OVERVIEW RODUCT DESCRIPTION The TUNGSTEN Gas Radiant Heater is designed to provide effective outdoor heating to both commercial and residential premises whilst offering an appealing design. The heater incorporates a pivoting head and adjustable heat output for precise heat control. The heater has been designed to withstand the rigors of the outdoors. SPECIFICATIONS TUNGSTEN SMART-HEAT™ PORTABLE Ignition 1.5V repetitive spark ignitor Manufactured by BROMIC PTY. LTD AGA approval number AGA 8064 G Gas consumption 23.5 Mj/h - 40 Mj/h Gas Type Universal LP Gas / Propane Only Gas Supply Universal LP Gas Cylinder / Propane Cylinder (9kg or 13.5kg Injector size 0.80mm Weight 56Kg Safety features Flame failure device, anti-tilt switch Gas supply pressure 2.75kPa TUNGSTEN SMART-HEAT™ HEATER DIMENSIONAL DETAILS IMPORTANT This appliance is to be protected from rain. Install under a protective cover. This appliance shall only be used in an above ground, open-air situation with sufficient natural ventilation. The heater must not be operated in any stagnant areas and should be positioned where any potential gas leakage and products of combustion are rapidly dispersed by wind and natural convection. GENERAL INFORMATION The TUNGSTEN Gas Patio Heaters are suitable for outdoor spaces. In addition to the installation Instructions provided, the installer is to ensure that the requirements of the local authority, local gas fitting regulations, municipal building codes, and any other relevant statutory regulations are carried out. PRODUCT FEATURES TUNGSTEN Gas Patio Heaters are revolutionizing the outdoor heating industry by introducing ground breaking benefits never seen before in traditional gas or electric heaters. TUNGSTEN heaters have set the industry benchmark with stylish good looks and world-first innovation. TUNGSTEN heaters excel in the areas of: Aesthetic appeal Innovation Performance Flexibility Cost effectiveness For more detailed product information, visit www.bromicheating.com INSTALLATION REQUIREMENTS IMPORTANT This appliance is for outdoor use only. The appliance must be placed on level firm ground. This appliance shall only be used in above ground open-air situations with: natural ventilation without stagnant areas where gas leakage and products of combustion are rapidly dispersed by wind and natural convection Any enclosure in which the appliance is used shall comply with one of the following: An enclosure with walls on all sides, but at least one permanent opening at ground level (ref. Appendix A, Example 1) Within a partial enclosure that includes an overhead cover and no more than two walls (ref. Appendix A, Example 2) Within a partial enclosure that includes an overhead cover and more than two walls, the following shall apply: At least 25% of the total wall area is completely open (ref. Appendix A, Example 4), and At least 30% of the remaining wall area is open and unrestricted (ref. Appendix A, Example 4) In the case of balconies, at least 20% of the total wall area shall be and remain open and unrestricted. Note: The definition of outdoors is an above ground openair situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection. GAS REQUIREMENTS This appliance is for use with a Universal LP Gas cylinder / Propane cylinder (9kg or 13.5kg) and MUST NOT be connected to a fixed gas supply. Regulator outlet pressure to be 2.75kPa. The pressure regulator and hose assembly supplied with the appliance must be used. Replacement regulator and hose assemblies must be purchased from Bromic Heating Pty Ltd. A dented, rusted or damaged cylinder may be hazardous and should be checked by your gas supplier. Never use an LPG cylinder with a damaged valve connection. The LPG cylinder must be arranged to provide for vapour withdrawal from the operating cylinder. Never connect an unregulated cylinder to the heater. Disconnect the LPG cylinder when the heater is not in use. LOCATION CLEARANCES When selecting the location for the TUNGSTEN Gas Patio Heater, the following clearances should be followed. Care should be taken to ensure that the heater is not installed: Where heat/ignition can cause damage to gas cylinders/lines Near other combustible materials In open locations subject to rain Note: Heater should be installed in such a way so as to allow adequate; Clearance around air openings to combustion chamber Clearance from combustible material Provisions for accessibility and clearance for combustion and ventilating air supply. IMPORTANT This appliance must only be used in a well ventilated area. When selecting the installation location for the Tungsten Smart-Heat Portable, the following clearances should be followed. INSTALLATION INSTRUCTIONS CONTENTS PACKED IN (2) BOXES Box 1 Contents Head Assembly AAA Battery Box 2 Contents Base Assembly Front Assembly Rear Arm Assembly x 2 Side Panels x 2 Top Arms x 2 Rear Cover Top Flame Deflector Regulator Supplied Fasteners M8 x 95mm QTY: 4 M8 x 40mm QTY: 2 M8 x 16mm QTY: 2 M5 x 8mm QTY: 4 G8 x 8mm QTY: 16 M8 x 20mm QTY: 4 Supplied Tools M8 Hex Key Tools Not Included Phillips head screw driver and Spray Bottle STEP 1: Unpack boxes and place all items on a non abrasive surface. STEP 2: Fasten rear arms to base using 2 x M8 20mm screws and the supplied M8 Hex Key STEP 3: Position front assembly and fasten using 2 x M8 20mm screws using supplied M8 Hex Key. STEP 4: Secure the rear arms to front assembly using 2 x M8 x 16mm screws and supplied M8 Hex Key. STEP 5: Secure the side panels to frame using 12 x G8 screws - A Phillips screw driver is required for this step. Repeat for opposite side. STEP 6: Slide top arms over front assembly slip joints - Ensure top screw holes are faced inwards. Secure the front panel to top arms using 4 x M5 screws. Note: The joint between the lower and upper arms is firm to ensure' rigidly and stability of the product. To engage slowly lever the two sections together using some force and push down fully STEP 7: Secure the top arms to lower arm slip joint using 2 x M8 x40 screws and supplied M8 Hex Key. STEP 8: Lay both heater head and stand on a non abrasive surface as shown. Two people are required for this step. NON ABRASIVE SURFACE STEP 9: Feed gas hose through arm slot and push through until it reaches slot in bottom arm. Keep feeding hose until all slack is taken up. STEP 10: Secure the heater head to arms using 4 x M8 screws and supplied washers. STEP 11: Return heater to upright position. Two people are required for this step. NON ABRASIVE SURFACE STEP 12: Fill base with fine grain sand (this sand can be purchased from most hardware stores). Entry point for the sand is the hole at the centre of the base. STEP 14: Screw regulator assembly to gas bottle. STEP 15: Place gas bottle into lower enclosure and fasten strap tightly. STEP 16: Pull sleeve back on regulator connector, insert hose fitting & release sleeve on regulator connector. STEP 17: Lower gas bottle bracket into position. STEP 18: Secure deflector to heater by loosening the two screws and secure brackets underneath washers. Re-tighten screws to original position using screw driver. STEP 19: Unscrew igniter cap. Insert supplied AAA battery into cap and rescue to original position STEP 20: Perform Gas leakage test as shown on page 20 STEP 21: Secure the top piece of rear cover to frame using 4 x G8 screws - A Phillips screw driver is required for this step. The bottom piece of rear cover is secured by magnets. Firstly position slots in back cover over the two hooks then lower cover to allow magnets to catch Adjusting the heater head angle CAUTION: ONLY ADJUST THE HEATER HEAD ANGLE PRIOR TO OPERATION. ADJUSTING WHILST UNIT IS IN OPERATION OR POST OPERATION CAN CAUSE SERIOUS BURNS To set heater head angle at high position, manually push heater head up to align hole then insert slip pin. To set heater head angle at low position, remove slip pin & allow heater head to rest in low position. Slip pin does not need to be inserted. Note: The slip pin must be inserted if transporting the heater to enure no damage during transit. LEAK TEST Gas connections on heater are leak tested at the factory prior to shipment. A complete gas leak test must also be performed after assembly before operating the heater due to possible damage occurring during transportation. Never leak test while smoking. The heater must be checked with a full gas cylinder. Ensure connection all 3 connections illustrated below are connected correctly & tight. Make sure the control knob is in the OFF position. Make a mild soapy water solution. The soapy solution can be applied with a spray bottle, or soft cloth. Turn on the gas supply at the gas cylinder. Apply the soapy water solution to the 3 connections illustrated below. To check connection #3 the gas control knob must be pressed in to open the gas valve. If bubbles appear at any of the connections, there is a gas leak. If a gas leak is detected, turn off the gas supply. Tighten any leaking fittings, and repeat process described above. If soap bubbles still appear (gas is still leaking), turn off the gas supply at the cylinder, disconnect the regulator from the gas cylinder, and contact the store of purchase for assistance and advice. If gas connections are gas tight, the heater is ready to be used. OPERATING INSTRUCTIONS TURNING THE APPLIANCE ON Ensure that installation has been carried out in accordance with the manufacturers instructions outlined in this document. Test the spark ignite button is working correctly by pressing the button and observing sparks at the ignition rods at the front of the heater. If sparks are not observed do not proceed with turning appliance on. Contact the store of purchase for assistance and advice. WARNING Do not turn the heater on with people standing in front of heater. Heater must be turned on while standing behind the heater. WARNING Improper lighting procedures can cause personal injury, property damage, or even death. Turn ON the gas supply at the LPG storage bottle. Turn on gas control knob to maximum setting. Push in and hold control knob whilst simultaneously pressing the spark ignite button. Continue to hold in the controls for 10 seconds for ignition to complete. Release the controls. If the heater has not ignited wait 5 minutes and then repeat Step 5. When appliance is correctly turned on the tiles will start to glow red. TURNING THE APPLIANCE OFF Press and turn the control knob to “OFF” position to stop the supply of gas to the burner. The tiles should change colour from red to black. Turn OFF the gas supply at the LPG storage bottle. WARNING - After turning heater off, you must wait a minimum 5 minutes to let excess gas dissipate before lighting again. MAINTENANCE AND SERVICING It is important that regular maintenance is carried out on the heater to maintain efficient operation. All maintenance should be carried out ONLY by authorized service personnel. Inspect and clean at least every six months or more frequently in adverse conditions. Never obstruct the flow of combustion and ventilation air. Always keep the appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. Do not clean heater with cleaners that are combustible or corrosive. REGULAR SERVICE REQUIREMENTS The whole gas system, hose assembly, regulator, pipes, and burner should be inspected for damage and leaks before each use and at least annually by an authorized person for the life of the heater. To check the gas hose within the mounting arm, disassemble heater by reversing the installation instructions as outlined in installation section of this manual. The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of excessive abrasion or wear, or if the hose is damaged. The replacement hose must be purchased from Bromic Heating Pty Ltd. VISUALLY CHECK BURNER FLAMES. During heaters function visually check that all burners are alight and glowing hot. This can be done by observing the red glow through the translucent face, or by peering down the product combustion passageway. Note: A slight variation in colour is to be expected. Clean burners: Burners can be cleaned by directing compressed air (max20PSI) at outlet ports. Avoid directing air at gasket material between ceramic tile and burner cup. Clean manifold and injectors: Undo gas hose from gas valve outlet (heater should be switched off) and inject compressed air (max20PSI) down the inlet fittings. Clean dust and foreign matter from inside of heater housing: Open up rear housing and clear dust using compressed air (max20PSI) and a damp cloth. Remove debris, spider and insect nests from, control compartment, burner and circulation air passageways of the heater with heavy-duty pipe cleaner or compressed air to keep appliance clean and safe for use. Never clear ports or other openings with toothpicks or other articles that will break and block the ports. In a salt-air environment, such as near an ocean, corrosion occurs more quickly than normal. Remove salt spray from the heater immediately to prolong heater life. Check frequently for corroded areas and repair them promptly. The exterior components of the heater are constructed Over the life of the heater internal non-painted parts may slightly discolour from high temperatures emitted by the heater. This is a normal occurrence and does not affect the operation of the appliance. Replacement parts can be purchased to restore the heater to its original appearance from Bromic Heating Pty Ltd. IMPORTANT Service and repair should be done by a qualified service person. The heater should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air passageways of the heater be kept clean. IMPORTANT Do not apply any additional surface coating to the heater under any circumstances. Use of additional coating other than those applied during manufacture could result in hazardous reactions such as toxic fumes or fires. Additional coatings will void the warranty. STORAGE There is no limitation on the storage of appliances indoors provided that the cylinder is removed from the appliance. Storage of an appliance indoors with the cylinder attached is only permitted if the size of the cylinder complies with AS/ NZS 1596; otherwise cylinders must be stored outdoors in a well-ventilated area. Always close the gas valve on the gas cylinder after use. Remove the pressure regulator and hose assembly. Cylinder must be stored outdoors in a well-ventilated area out of the reach of children. Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a garage or any other enclosed area. Check the tightness of the gas valve and for damage. If you suspect you have a damaged gas cylinder valve, contact your place of purchase. Only store gas cylinders in places with adequate air ventilation. REPLACEMENT PARTS An authorised service technician MUST replace any faulty items with the correct approved component from the list below. Contact your place of purchase to organize any of the replacements parts below. No: Description Part No: 1 Control Knob 2620352 2 Gas Valve 2620353 3 Ignition Pack 2620354 4 Cylinder Housing - Rear Cover 2620355 5 Cylinder Housing - Side Panel 2620356 6 Inner Mesh 2620357 7 Cylinder Housing - Front Panel Assembly 2620358 8 Burner Box 2620359 9 Thermocouple Assembly 2620360 10 Front Cover 2620361 11 Ignition & Earth Rod Assembly (Inc. Wir- ing Harness) 2620362 12 Heat Deflector Assembly 2620363 13 Wheel Kit (Left & Right Set) 2620364 14 Screw Set 2620365 15 Cylinder Housing – Rear Arms With Mag- nets 2620366 16 Rubber Ring (From Rear Cylinder Cover) 2620367 TROUBLESHOOTING Problem Possible cause What you can do (if these do not work, contact an authorised technician) What ONLY an authorised service technician can do Burner will not light • Gas valve may be OFF • Tank fuel empty • Opening blocked • Turn the gas valve ON • Check all fittings • Refill LPG tank • Remove and clean • Loose connections • Low gas pressure • Replace cylinder with a new cylinder • Replace thermocouple • Thermocouple bad • Not in correct location Burner will not • Loose connections • Tighten connections • Clean dirty area stay on • Thermocouple bad • Gas leak in line • Check connections • Replace thermocouple • Lack of fuel pressure • Refill LPG tank. • Tank near empty Burner flame is low • Supply hose is bent or twisted • Straighten hose and perform leak test on hose Emitter glows uneven • Low gas pressure • Base is not on a level surface • Replace cylinder with a new cylinder • Place heater on a level surface Thick black smoke • Blockage in burner • Turn off the heater and let it cool. • Remove blockage and clear burner inside and outside Carbon build-up • Dirt or film on reflector and flame screen • Clean reflector and flame screen APPENDIX A OUTDOOR AREA-EXAMLE 1 OUTDOOR AREA-EXAMLE 2 OUTDOOR AREA-EXAMLE 3 OUTDOOR AREA-EXAMLE 4 OUTDOOR AREA-EXAMLE 5

Discover the TUNGSTEN Smart-Heat Portable Heater by Bromic, designed for efficient outdoor heating. Follow the installation manual for gas radiant heater model Tungsten Smart-Heat Portable. Prioritize safety with gas detection alerts and proper setup for optimal performance.

U-BOAT 50MM Classico Tungsten Instruction Manual

Discover how to operate and maintain your 50MM Classico Tungsten watch with this comprehensive user manual. Learn about the various components and functions, including winding, date and time setting. For any maintenance needs, contact U-BOAT Head Office in Italy.