TAC TB-D11N Arrow Side Step
Specifications
- Product: Arrow Side Step
- Part Number: TB-D11N
- Compatibility: Fits 2019-Up Dodge RAM 1500 Crew Cab (Exclude
2019-2024 RAM 1500 Classic Crew Cab) - Installation Time: 60-120 minutes
- Cutting Not Required
- Drilling Not Required
FAQ
- Q: Is drilling required for installation?
- A: No, drilling is not required for installing the Arrow Side Step.
- Q: What tools are needed for installation?
- A: Tools required include wrenches in sizes of 10mm, 13mm, 16mm, and 18mm, as well as Allen wrenches in sizes of 4mm, 5mm, 6mm, and 8mm.
Torque & Tools
| Fastener Size | Tightening Torque (ft-lbs) | Wrench Required | Allen Wrench Required | ||
| 6mm | 7-8.5 |  |
10mm |  |
4mm |
| 8mm | 18-20 | 13mm | 5mm | ||
| 10mm | 35-40 | 16mm | 6mm | ||
| 12mm | 60-70 | 18mm | 8mm | ||
BEFORE INSTALLATION
- REMOVE CONTENTS FROM THE BOX.
- VERIFY ALL PARTS ARE PRESENT.
- READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- ASSISTANCE IS RECOMMENDED.
Part List
- Front/Rear Lower Mounting Bracket x 4
- Front/Rear Upper Mounting Bracket x 4
- Center Mounting Bracket x 2
- Center Support Bracket x 2
Installation Instructions
PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE DRIVER-SIDE INSTALLATION
STEP 1
- Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Fig 1).
STEP 2
- Select (1) Front/Rear Upper Mounting Bracket (#2). Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Fig 2). Do not tighten hardware.
STEP 3
- Attach (1) Front/Rear Lower Mounting Bracket (#1) to the welded plate on the back of the Front Upper Bracket (#2) with (2) 8mm Hex Bolts, (4) 8mm x 16mm Flat Washer, and (2) 8mm Nylon Lock Nuts (Fig 3).
STEP 4
- Move to the center location, (Fig 4). Select (1) Center Support Bracket (#4), attach the Support Bracket to the lower (2) factory studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 5).
STEP 5
- Select (1) Center Mounting Bracket (#3) and attach to the Support Bracket and upper threaded stud with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 6). Do not tighten hardware.
STEP 6
- Repeat Steps 2 & 3 to attach (1) Front/Rear Upper Mounting Bracket (#2) and (1) Front/Rear Lower Mounting Bracket (#1) to the rear mounting locations along the body panel, (Fig 7). Do not tighten hardware.
STEP 7
- Select the Driver/Left Side Step. Insert (6) 6mm TBolts into the slots underneath the Side Step (Fig 8).
- NOTE: The Driver/Left Side Step will have a Sticker “D” on the front.
- IMPORTANT: Do not slide the Side Step front to back or damage to the finish may result.
- Attach the Side Step to the (3) Mounting Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers, and (6) 6mm Hex Nuts (Fig 9). Do not tighten hardware.
STEP 8
- Level and adjust the Side Step as necessary and fully tighten all hardware.
STEP 9
- Repeat Steps 1-8 to attach the Passenger/Right Side Step to the vehicle.
STEP 10
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Attention
- To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
- Mild soap may be used also to clean the Side Steps.
CONTACT
- www.tacautoparts.com.
- Customer Support: tac-office@tacautoparts.com.
Documents / Resources
 |
TAC TB-D11N Arrow Side Step [pdf] Installation Guide TB-D11N Arrow Side Step, TB-D11N, Arrow Side Step, Side Step, Step |