T-LED PR 1KRF dimLED Single Color LED Controller Owner’s Manual

PR 1KRF dimLED Single Color LED Controller

Specifications

  • Product Name: 069001 dimLED PR 1KRF
  • Type: Single Color LED Controller
  • Dimming Levels: 4096 levels, 0-100%
  • Control Method: RF 2.4G single zone or multiple zone dimming
    remote control
  • Control Distance: Up to 30m
  • Input Voltage: 5-36VDC
  • Input Current: 8.5A
  • Output Voltage: 5-36VDC
  • Output Current: 1CH, 8A
  • Output Power: 40W/96W/192W/288W (5V/12V/24V/36V)
  • Output Type: Constant voltage
  • Package Size: L114 x W38 x H26mm
  • Gross Weight: 0.052kg
  • Operation Temperature: -30°C to +55°C
  • Case Temperature (Max.): +85°C
  • IP Rating: IP20

Product Usage Instructions

Installation

1. Wire Preparation:

Ensure terminals are tightly secured to prevent high contact
point resistance and terminal burnout.

Wiring Diagram:

Wiring Diagram

Match Remote Control:

User can choose between two ways to match or delete remotes:

  1. Using the controller’s Match key:
  • – Short press match key, then immediately press on/off key
    (single zone remote) or zone key (multiple zone remote) on the
    remote.
  • – LED indicator will fast flash a few times to indicate
    successful match.
  • Using Power Restart:
    • – Switch off the power of the receiver, then switch on power,
      repeat again.
    • – Immediately short press on/off key (single zone remote) or
      zone key (multiple zone remote) 3 times on the remote.
    • – The light blinks 3 times to confirm successful match.

    Frequently Asked Questions (FAQ)

    Q: How many remote controls can be paired with one RF
    controller?

    A: One RF controller can accept up to 10 remote controls.

    Q: What is the dimming range of the controller?

    A: The dimming range is from 0-100% smoothly without any
    flicker.

    069001 dimLED PR 1KRF
    Single Color LED Controller
    4096 levels 0-100% dimming smoothly without any ash. Match with RF 2.4G single zone or multiple zone dimming remote control. One RF controller accept up to 10 remote control. Auto-transmitting function: Controller automatically transmit signal to another controller
    with 30m control distance. Synchronize on multiple number of controllers. Connect with external push switch to achieve on/off and 0-100% dimming function. Light on/off fade time 3s selectable. Over-heat / Over-load / Short circuit protection, recover automatically.

    RF DIM

    RED

    1 Channel / Step-less dimming / Wireless remote control / Auto-transmitting / Synchronize / Push Dim / Multiple protection

    Technical Parameters

    Input and Output Input voltage Input current Output voltage Output current
    Output power
    Output type Package Size Gross weight

    5-36VDC 8.5A 5-36VDC 1CH,8A 40W/96W/192W/288W (5V/12V/24V/36V) Constant voltage
    L114 x W38 x H26mm 0.052kg

    Dimming data Input signal Control distance Dimming gray scale Dimming range Dimming curve PWM frequency
    Environment Operation temperature Case temperature (Max.) IP rating

    RF 2.4GHz + Push Dim 30m(Barrier-free space) 4096 (2^12) levels 0 -100% Logarithmic 2000Hz (default)
    Ta: -30 OC ~ +55 OC Tc: +85 OC IP20

    Safety and EMC EMC standard
    Safety standard Radio Equipment Certi cation Warranty and Protection Warranty
    Protection

    ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 61347-1:2015+A1:2021 EN 61347-2-13:2014+A1:2017 ETSI EN 300 328 V2.2.2
    CE RED
    3 years Reverse polarity Over-heat Over-load Short circuit

    Mechanical Structures and Installations

    LED indicator Push switch com
    Push switch in Installation rack Match key

    LED output LED output + Power input Power input +
    Installation rack

    33mm

    97mm 18mm

    Match Remote Control (two match ways)

    End user can choose the suitable match/delete ways. Two options are offered for selection:

    Use the controller’s Match key

    Use Power Restart

    Match: Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. The LED indicator fast flash a few times means match is successful.

    Match: Switch off the power of the receiver, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful.

    Delete: Press and hold match key for 5s to delete all match, the LED indicator fast flash a few times means all matched remotes were deleted.

    Delete: Switch off the power of the receiver, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.

    User Manual Ver 1.1.6 2024.9

    Page 1

    Wiring Diagram

    OUTPUT

    Push Switch
    RF remote

    PUSH-DIM GND PUSH

    PUSH-DIM GND PUSH

    LED Controller LED Controller

    OUTPUT

    INPUT 5-36VDC

    Single color LED strip
    +
    Single color LED strip
    +

    Power Supply 5-36VDC Constant Voltage

    AC100-240V

    INPUT 5-36VDC

    Wire Preparation:
    1. The wiring can be solid or stranded with a cross-sectional area of 0.5 to 2.5 mm². Conventional 1mm² can withstand 10A output current.
    2. When wiring is installed, the terminals must be tightened. If they are not tightened, the contact point resistance will be too high and the terminals will easily burn due to heat when used at full load for a long time.

    Note: The output power of a constant voltage power supply should be at least 1.2 times that of the output load (light strip), otherwise the full power output of the load can easily cause automatic flickering or shaking of the light.
    Push Dim Function

    The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs. Short press: Turn on or off light. Long press (1-6s): Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction. Dimming memory: Light returns to the previous dimming level when switched off and on again, even at power failure. Synchronization: If more than one controller are connected to the same push switch, do a long press for more than 10s,then the system is synchronized and all lights
    in the group dim up to 100%. This means there is no need for any additional synchrony wire in larger installations.We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to controller should be no more than 20 meters.

    Dimming Curve

    Light on/off fade time

    PWM duty(%)

    100
    Gamma=1.6
    90 80 70 60 50 40 30 20 10
    10 20 30 40 50 60 70 80 90 100
    Brightness(%)
    Malfunctions Analysis & Troubleshooting

    Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times.
    Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

    Malfunctions No light
    Uneven intensity between front and rear,with voltage drop
    No response from the remote

    Causes 1. Nopower . 2. Wrongconnection or insecure . 1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability.
    1. The battery has no power. 2. Beyond controllable distance. 3. The controller did not match the remote.

    Troubleshooting 1. Check the power. 2. Check the connection. 1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater.
    1. Replace battery. 2. Reduce remote distance. 3. Re-match the remote.

    InstallationPrecautions

    1. The products shall not be stacked, the distance should be 20cm, so as not to affect lifespan of the products due to poor heat dissipation. 2. The product shall not be installed close to the switching power supply with an interval of 20cm to avoid radiation interference of the switching power supply. 3. The installation height shall be 1m from the oor to avoid shortening the remote control distance due to too weak reception signal. 4. The products are not allowed to be close to or covered by metal objects, with an interval of 20cm to avoid signal attenuation and shorten the remotedistance. 5. Avoid installation at the corner of the wall or the corner of the beam, with an interval of 20cm to avoid signal interference.

    User Manual Ver 1.1.6 2024.9

    Page 2

    Documents / Resources

    T-LED PR 1KRF dimLED Single Color LED Controller [pdf] Owner's Manual
    069001, PR 1KRF, PR 1KRF dimLED Single Color LED Controller, PR 1KRF, dimLED Single Color LED Controller, Single Color LED Controller, Color LED Controller, LED Controller

    References

    Leave a comment

    Your email address will not be published. Required fields are marked *