Sysgration TA-82P TPMS Repeater User Manual
Product Introduction
The Repeater is designed to amplify the signal from your Bluetooth Low Energy TPMS (Tire Pressure Monitoring System) system sensors. In situations where the size of the vehicle and excessive metal may obstruct signal reception or interference prevents, the Repeater increases the sensors transmitting strength and distance.
Repeater Specification
- Truck Repeater Specification
- These LED patterns are displayed under the conditions of defined events.
Installation Steps
Can be mounted anywhere outside the vehicle Weather-resistant.
Please don’t directly connect to the storage battery.
Warranty Policy
Thank you for buying this product and giving us support. From the date of purchase, we provide a one-year warranty for the product, protecting the client’s interest by providing product quality assurance. During the warranty period, under normal operation and in the event of a faulty product, the company is willing to repair the faulty product or have it replaced, enabling you to get the guarantee and demonstrating the company’s responsible attitude toward products. But the product warranty must meet the following conditions:
- Defective products need to be provided to the local dealer to confirm the purchase date and cause of the defect.
- Products must be operated correctly, as indicated in the user manual.
- Product has not been disassembled by yourself.
- The main cause of product failure is due to manufacturing issues.
NCC
“For low-power radio frequency equipment that has obtained certification, no company, company or user may change the frequency, increase the power, or change the characteristics and functions of the original design without approval. The use of low-power radio frequency equipment must not affect flight safety or interfere with legal communications; if interference is found, it should be stopped immediately and improved until no interference is allowed to continue to be used. The aforementioned legal communications refer to radio communications that operate in accordance with the provisions of the Telecommunications Management Act. Low-power radio frequency equipment must endure legal communications or industrial, scientific and medical use Interference from electrical equipment caused by radio wave radiation.”
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement:
This equipment complies with RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Documents / Resources
 |
Sysgration TA-82P TPMS Repeater [pdf] User Manual TA82P, HQXTA82P, TA-82P TPMS Repeater, TA-82P, TPMS Repeater, Repeater |