SWIT WAVE500 Wireless Microphone User Manual

Model: WAVE500
Wireless Microphone
User Manual

WAVE500 Wireless Microphone

Please read this user manual throughout before using
Ver: A
WARRANTY CERTIFICATE
Please register y o u r warranty. Meanwhile, you are welcomed to contact us via Email: contact@swit.cc 

USER INFORMATION	Customer Name:
	Phone Number:
	Email:
	Address:
SALES INFORMATION	Sales Date:
	Model:
	Product Code:
	Dealer:
REPAIR RECORD	Service Date:
	Technician:
	Issue:
RESULT	Solved	Unsolved	Returned(Replaced)

Caring For Your SWIT Product

• Please keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.
• Use only a soft and dry cloth for cleaning the product.
• Malfunction may be caused by dropping, impact of external force.
• Do not attempt to disassemble the product. Doing so voids warranty.
• Please hav e the product checked or repaired by authorized technicians if any malfunctions happened.
• Failure t o follow all the instructions may result in mechanics damage.
• Warranty does not apply to human errors.

Package List

Product Instruction

TX Transmitter 

RX Receiver

Display Screen 

Operations

TX
1.Power/ Mute 

Long Press 2s: turn on/off the system
Short Press: mute/unmute the microphone

2. Charging

5V/2A;with USB-C Charging Cable
Please fully charge the product before use.
3.External Mic Input 

TRS Mic Only
(Note: When using a external mic, please insert it into the mic input properly.)
4.Mic Windshield & Device Installation

5. Reset 

6. Low Cut

Short Press: 150 Hz Low Cut On
Short Press again: Low Cut Off
7. Pairing  

The system will pair automatically after power on.
(Note: Before success fully connecting, the transmitter channel will display A by default. The TX connected to the receiver first is Channel A , and the one connected later is Channel B.)
Manual pairing: long press the Channel A Gain Control and Channel B Gain Control on the RX and Pairing on the TX for 3 seconds at the same time
RX
1. Power/ Mono/Stereo Switch

Long Press 2s: turn on/off the system
Short Press: Switch Mono/Stereo mode (Note: Stereo mode is unavailable in phone devices.)

2. Charging 

5V/2A;with USB-C Charging Cable
Please fully charge the product before use.
3. Reset 

4. Gain Control

0-5 Level(0 → 3 → 6 → 9 → 12 → 15 → 0)
Each press increases the gain of Channel A / Channel B b y one level.
5. Pairing 

The system will pair automatically after power on.
Manual pairing: long press the Channel A Gain Control and Channel B Gain Control on the RX and Pairing on the TX for 3 seconds at the same time
(Note: The first TX that successfully connects with the RX will be Channel A . )
6. Audio Monitoring & Output Connection

Setting The Recording Level Correctly

Camera devices generally have poor-quality, noisy preamps. In order to get the cleanest signals possible, it is highly recommended that you set the recording level on your camera quite low, 1/2 or 1/3 of it. G2 provides variable gain control, allowing you to tail or your levels to just about environment and recording device.
Adjust the recording level of inbuilt mics for SONY Camera (Take A7S I I for example)

Adjust the recording level of inbuilt mics for Canon Camera (Take EOS 5D Mark I V for example)

Adjust the recording level of inbuilt mics for Panasonic Camera (Take LUMIX GH5 for example)

Specifications

TX Transmitter 

RX Receiver

Microphone

Warranty

Warranty Period
Thank you for purchasing SWIT products.

1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original SWIT products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user.

Within the warranty period, if product defect or failure i s attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations

• Faults resulted from inappropriate use of a product without following its operation specification
• Artificial damage, e.g. crash, squeeze, scratch, or soaking
•  Modifications to a product by its user or third party without prior written consent of SWIT, e.g. replacement of element or circuit, label alteration
• The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off
• All consumable accessory attached to a product, like cable, wind muff, battery
• Faults as a result of force majeure, such as fire , flood, lightning, etc.

Warranty Claim Procedure

• If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SWIT customer service through email at contact@swit.cc
• Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
• If the SWIT product is out of the warranty coverage, the service and the parts cost will be charged.

SWIT Electronics Co., Ltd.
Address: 10 Hengtong Road, Nanjing Economic and
Technological Development Zone,
Nanjing 210038, P.R.China
Phone: +86-25-85805753
F a x : +86-25-85805296
Email: contact@swit.cc
http://www.swit.cc