With 4 Outputs
ESP32 WLED Digital LED Kidhibiti
– User Instruction –
GL-C-017WL-D

Bidhaa Parameter

Mfano: GL-C-017WL-D
Jumla ya Pato la Sasa: ​​15A Max
Vipimo: 108x45x18mm
Uingizaji Voltage: DC 5-12-24V
Itifaki: WiFi
Joto: -20 ~ 45°C

Maagizo ya Kituo cha Wiring

1. The WLED controller can support a total of 4 output channels. The output terminal connections “V GND GPIO16 GPIO12 GPIO4 GPIO2” correspond to the “VCC DATA GND” pins of the digital LED strips.
2. IO13 is an extended GPIO signal port for custom use.

Mbinu ya Kupakua APP

IOS

1. Tafuta and download WLED Native in the App Store.
   Android
   Tafuta and download WLED Native in the Google Play Store.
   

Hatua za Usanidi wa APP

1. Washa kidhibiti cha WLED.
2. Open the phone settings and enter WiFi settings, find “WLED-AP” and connect to it with the password “wled1234”.
   
3. Baada ya muunganisho uliofanikiwa, itaruka kiotomatiki kwenye ukurasa wa WLED (au ingiza faili ya webtovuti 4.3.2.1 kwenye kivinjari ili kuingiza ukurasa wa WLED).
   
4. Click “WIFI SETTINGS”, set the WiFi account and password, and the click “Save & Connect” at the top of the screen to save.
   
5. Keep both your phone and the WLED controller connected to the same Wi-Fi network. Then, open the WLED-Native APP, and the WLED controller will be displayed in the list.
   

Kumbuka:

1. After the WLED controller disconnects from the router, the chip will restart and return to the preset state (you can find the hotspot “WLED-AP” in your phone’s WiFi settings).
2.  If the WLED controller is not displayed or cannot be found in the APP, you can open a browser, enter the IP address of the WLED controller, and use the web interface for control (To find the controller’s IP address: Connect to the Wi-Fi, locate the router’s or controller’s web address (usually found at the bottom of the router or on the controller itself), enter this address in the browser, and then you can view the controller’s IP address in the router’s backend interface).

Usanidi wa Ukanda wa LED

Enter into the WLED control page and click on the “Config” button in the upper right corner. Then, select “LED Preferences” and navigate to “Hardware setup” to configure the LED strip information.

Usanidi wa Relay

Enter into the WLED control page, click on the top right corner “Config”, select “LED Preferences”, then find “Relay GPIO”.
Configure Relay GPIO as 18, check Invert, and click Save to apply the settings.

Kumbuka:

1. The relay function is configured by default.
2.  When turning off the light via the APP, remote control, or PUSH switch, the power supply to the output terminal will be cut off to save energy. It should be noted that this function cannot deactivate the supplementary power supply.

Usanidi wa Maikrofoni

Enter the WLED control page, click “config” in the upper right corner, select “Usermods”, find “Audio Reactive”, check (Enabled), and then configure according to the configuration information under “Digitalin”. After the configuration is completed, click “save”. After the successful save, turn off the controller.
Maelezo ya Usanidi:

1. Type: Generic 12S PDM
2. Pin 12S SD: 32
3. Pin 12S WS: 15
   

Kumbuka:

1. The Mic function is configured by default.
2. After microphone function configured, it will be only activated after rebooting the controller again.

Maelezo ya Kazi za Kitufe

Anzisha upya:
Pressing the button will power off the controller module, releasing it will power it back on. Useful when the controller needs to be restarted after configuring the microphone.
Functions (GPIO17):

1. Bonyeza kwa muda mfupi: Washa/zima.
2. Bonyeza kwa muda mrefu kwa sekunde 1: Badilisha rangi.
3. Bonyeza kwa muda mrefu kwa sekunde 10: Weka upya kidhibiti cha WLED na uwashe mtandaopepe wa WLED-AP.

Weka upya kwa Mipangilio ya Kiwanda

1. Kitufe Rudisha
   Long press the “Function” button for 10 seconds.
2. Rudisha APP
   Enter into the WLED control page and click on the top right corner “Config”.
   Click on “Security & Updates” at the bottom, and then scroll down to find “Factory reset” and check the box. Click “Save” to reset the controller.

UART Download

1. Remove the power supply and light strip.
2. Ondoa makazi.
3. Connect the Type-C cable and start downloading.

Chips zinazotumika

WS2805, WS2811, WS2811F, WS2812B, WS2814A, WS2815, SK6812, SM16703, SM16703SP3, FL19038, FW1935, UCS2903B, nk.

Utatuzi na Utatuzi

Nambari	Dalili	Suluhisho
1	Nuru ya kiashirio haijawashwa	Check whether the input power connection is correct
2	APP inaonyesha "nje ya mtandao"	1. Angalia ikiwa simu iko kwenye mtandao sawa na kidhibiti. 2. Angalia ikiwa kidhibiti kiko nje ya anuwai ya muunganisho wa WIFI, na kusababisha muunganisho usio thabiti. 3. Zima na uweke kidhibiti ili ujaribu tena.
3	APP imeunganishwa, lakini ukanda wa mwanga hauwezi kudhibitiwa	1. Check if the power supply is working properly. 2. Angalia ikiwa ugavi wa umeme ujazotage inalingana na ukanda wa mwanga. 3. Angalia ikiwa muunganisho wa nguvu ya pembejeo ni sahihi. 4. Angalia ikiwa unganisho la ukanda wa mwanga ni sahihi. 5. Angalia ikiwa mipangilio ya GPIO kwenye APP ni sahihi. 6. Angalia ikiwa kielelezo cha IC cha ukanda wa mwanga kwenye APP kimewekwa kwa usahihi.
4	Mwangaza wa ukanda wa mwanga ni mdogo, na rangi ya mbele na ya nyuma ni tofauti sana	1. Angalia ikiwa usambazaji wa umeme unafanya kazi vizuri. 2. Angalia ikiwa usambazaji wa umeme unalingana na ukanda wa mwanga. 3. Angalia ikiwa miunganisho yote ni nzuri, na utumie waya za conductive na fupi iwezekanavyo kwa uunganisho. 4. Ongeza usambazaji wa nguvu katika nafasi inayofaa. 5.  Check if the APP has set a limit on brightness or current.

1. Before turning on the power, please ensure that all connections are correct
   and secure, and do not operate while the power is on.
2. Bidhaa hiyo inapaswa kutumika chini ya ujazo uliokadiriwatage. Kuitumia chini ya kiwango cha kupita kiasi au dunitage inaweza kusababisha uharibifu.
3. Usitenganishe bidhaa, kwani inaweza kusababisha moto na mshtuko wa umeme.
4. Usitumie bidhaa katika mazingira yaliyo wazi kwa jua moja kwa moja, unyevu, joto la juu, nk.
5. Usitumie bidhaa katika sehemu zilizolindwa na chuma au karibu na sehemu zenye nguvu za sumaku, kwa sababu hii inaweza kuathiri kwa kiasi kikubwa upitishaji wa mawimbi ya bidhaa bila waya.

Kanusho

1. Kampuni yetu itasasisha maudhui ya mwongozo huu kulingana na uboreshaji wa utendaji wa bidhaa. Masasisho yataonyeshwa katika toleo jipya zaidi la mwongozo huu, bila ilani zaidi.
2. Kwa sababu ya kuendelea kutumia teknolojia mpya, vipimo vya bidhaa vinaweza kubadilika bila taarifa zaidi.
3. Mwongozo huu umetolewa kwa ajili ya marejeleo na mwongozo pekee na hauhakikishi uwiano kamili na bidhaa halisi. Maombi halisi yanapaswa kutegemea bidhaa halisi.
4. Vipengele na vifuasi vilivyoelezewa katika mwongozo huu haviwakilishi usanidi wa kawaida wa bidhaa. Usanidi maalum unategemea ufungaji.
5. Maandishi, majedwali na picha zote katika mwongozo huu zinalindwa na sheria husika za kitaifa na haziwezi kutumika bila idhini yetu.
6. This product may be compatible with third-party products, but our company does not take responsibility for compatibility issues or partial loss of functionality caused by changes in third-party products.

GL-C-I-017WL(PDM)

Nyaraka / Rasilimali

SUPERLIGHTINGLED GL-C-017WL-D 4 Outputs ESP32 WLED Digital LED Controller [pdf] Mwongozo wa Mtumiaji GL-C-017WL-D 4 Outputs ESP32 WLED Digital LED Controller, GL-C-017WL-D, 4 Outputs ESP32 WLED Digital LED Controller, ESP32 WLED Digital LED Controller, WLED Digital LED Controller, Digital LED Controller, LED Controller

Marejeleo

• Mwongozo wa Mtumiaji