Teknolojia ya EDA ED-MONITOR-070C Uendeshaji na Udhibiti wa Kiwanda
Mwongozo wa vifaa
Sura hii inatanguliza juu ya bidhaaview, packaging list, appearance, buttons, indicators, and interfaces.
Zaidiview
The ED-MONITOR-070C is a 7-inch industrial touch monitor featuring a screen resolution of 1024×600, a high brightness of 425 cd/m², and a multi-touch capacitive touch screen. It includes one standard HDMI interface, one Type-C USB port, one DC Jack power interface, and one 3.5mm audio jack, making it compatible with various general-purpose PC hosts. The backlight can be adjusted via buttons, and it is primarily used in industrial control applications.
- The HDMI interface allows direct connection to the HDMI output of a PC host.
- The Type-C USB port transmits touch screen signals.
- The 3.5mm audio jack supports headphone connectivity.
- The DC Jack power interface supports 12V~24V DC input.
Orodha ya Ufungashaji
1 x ED-MONITOR-070C Monitor
Appearancel
Sehemu hii inatanguliza kazi na ufafanuzi wa violesura kwenye kila paneli.
Jopo la mbele
Tunakuletea aina na ufafanuzi wa violesura kwenye paneli ya mbele. 
| HAPANA. | Maelezo |
| 1 | 1 × LCD screen, 7-inch touch screen with a resolution of 1024×600, multi-touch capacitive touch screen. |
Paneli ya nyuma
Tunakuletea aina na ufafanuzi wa violesura kwenye paneli ya nyuma.
| HAPANA. | Maelezo |
| 1 | 4 x mashimo ya ufungaji ya snap, ambayo hutumiwa kurekebisha snaps kwenye kifaa kwa ajili ya ufungaji. |
| 2 | 4 x mashimo ya kupachika ya VESA, yaliyotengwa kwa ajili ya usakinishaji wa mabano ya VESA. |
Paneli ya Upande
Tunakuletea aina na ufafanuzi wa violesura kwenye paneli ya pembeni.
| HAPANA. | Maelezo |
| 1 | 1 × 3.5mm stereo audio output jack, supports headphone connectivity. |
| 2 | 1 × red power indicator, using to view hali ya kuwasha na kuzima kwa kifaa. |
| 3 | 1 × DC input, DC Jack connector, which supports 12V~24V DC input. |
| 4 | 1 × HDMI input, Type-A connector, which connects to the HDMI output of a PC host. |
| HAPANA. | Maelezo |
|
5 |
1 × USB touch screen port, Type-C USB connector, which connects to the USB port of a PC host to transmit touch screen signals. |
|
6 |
1 × Rubber plug (pre-drilled 7mm diameter circular cable routing hole), designed to accommodate additional cable management needs. |
| 7 | 1 × “Brightness –” button, press the button to decrease the backlight brightness of the LCD screen. |
| 8 | 1 × “Brightness +” button, press the button to increase the backlight brightness of the LCD screen. |
Kitufe
The ED-MONITOR-070C device includes two backlight brightness adjustment buttons. The buttons are black in color and marked with screen-printed labels 
juu ya makazi.
| Kitufe | Maelezo |
 |
Press the button to increase the backlight brightness of the LCD screen. |
 |
Press the button to decrease the backlight brightness of the LCD screen. |
Kiashiria
The ED-MONITOR-070C device includes a red power indicator, marked with the screen-printed label “PWR” on the housing.
| Kiashiria | Hali | Maelezo |
| PWR | On | Kifaa kimewashwa. |
| Blink | Power supply of the device is abnormal. Please stop the power supply immediately. | |
| Imezimwa | Kifaa hakijawashwa. |
Kiolesura
Kuanzisha ufafanuzi na kazi za kila kiolesura katika ED-MONITOR-070C.
Maingiliano ya Nguvu
Kifaa cha ED-MONITOR-070C kinajumuisha mlango 1 wa kuingiza umeme na kiunganishi cha DC Jack, kinachoitwa "24V DC" kwenye nyumba. Inaauni ingizo la 12V ~ 24V DC.
TIP
A 12V 2A power adapter is recommended.
- Muunganisho wa HDMI
The ED-MONITOR-070C device includes 1 HDMI input interface with a Type-A connector, labeled “HDMI INPUT” on the housing, used to connect to the HDMI output of a PC host. - Kiolesura cha USB cha Aina ya C
The ED-MONITOR-070C device includes 1 Type-C USB interface, labeled “USB TOUCH” on the housing. This interface connects to the USB port of a PC host to transmit touch screen signals. - Kiolesura cha Sauti
The ED-MONITOR-070C device includes 1 audio interface (3.5mm 4-pole headphone jack), labeled “AUDIO” on the housing, supporting stereo audio output.
Inasakinisha kifaa
The ED-MONITOR-070C device supports front embedded installation. The standard packaging does not include the embedded installation Mounting kit (ED-ACCHMI-Front). Please purchase the ED-ACCHMI-Front kit in advance.
Maandalizi:
The ED-ACCHMI-Front Mounting kit has been acquired (includes 4 × M4*10 screws, 4 × M4*16 screws, and 4 snaps).
Screwdriver ya msalaba imeandaliwa.
Hatua:
- Determine the cutout dimensions on the cabinet based on the ED-MONITOR-070C’s size, as shown in the figure below.
- Drill holes on the cabinet according to the aperture size defined in Step 1.
- Embed the ED-MONITOR-070C into the cabinet from the exterior side.
- Align the screw holes (non-threaded) of the snaps with the snap mounting holes on the device side.
- Secure the snaps to the device.
Use 4 × M4*10 screws to fasten the snaps to the device by threading them through the non-threaded holes and tightening them clockwise.
Then, use 4 × M4*16 screws to secure the snaps to the cabinet: Insert them through the threaded holes of the snaps, press against the interior side of the cabinet, and thread them clockwise until fully tightened.
Kutumia kifaa
The ED-MONITOR-070C requires a PC host for operation and does not require driver installation. Connect it to the HDMI output of a PC host first, then power on the device to enable normal display. It supports backlight adjustment via dedicated buttons and software.
Kuunganisha Cables
Sehemu hii inaelezea jinsi ya kuunganisha nyaya.
Maandalizi:
- A functional power adapter has been acquired.
- A functional PC host has been acquired.
- Functional HDMI and USB cables (Type-A to Type-C USB cable) have been acquired.
Mchoro wa mpangilio wa nyaya za kuunganisha:
Please refer to 1.6 Interface to obtain the pin definitions and wiring methods of each interface.
TIP
The HDMI INPUT interface of the ED-MONITOR-070C is compatible with various PC hosts. The figure below illustrates cable connection using a Raspberry Pi as an example. 
Kuanzisha kifaa
ED-MONITOR-070C haijumuishi swichi ya nguvu ya kimwili. Baada ya kuunganisha kwenye chanzo cha nguvu, kifaa kitawasha kiotomatiki. Mara baada ya kuanzishwa kikamilifu, itaonyesha eneo-kazi la seva pangishi ya PC iliyounganishwa.
Kurekebisha Mwangaza wa Mwangaza Nyuma
ED-MONITOR-070C supports brightness adjustment via physical buttons and software.Button-Based Brightness Adjustment
Once the ED-MONITOR-070C is connected to a PC and displays normally, its backlight brightness can be adjusted using the two dedicated brightness adjustment buttons on the side panel.
| Kitufe | Maelezo |
|
Press the button to increase the backlight brightness of the LCD screen. |
|
Press the button to decrease the backlight brightness of the LCD screen. |
Software-Based Brightness Adjustment
After connecting the ED-MONITOR-070C to a PC host and ensuring normal display operation, the screen backlight can be adjusted via software. Note that the operation methods differ between the Desktop and Lite versions of the operating system.
Raspberry Pi OS (Desktop)
Adjusting backlight brightness via UI on Raspberry Pi OS (Desktop).
Maandalizi:
ED-MONITOR-070C is properly connected to the Raspberry Pi host with normal display output. • The Raspberry Pi host has stable network connectivity.
Hatua:
- Add EDATEC apt repository by executing the following commands sequentially in the terminal.
Install the software toolkit. 
- Bofya kwenye
icon in the top-left desktop corner. Then select to “System Tools” → “EDATEC Monitor”. 
- Adjust brightness using the slider in the “EDATEC Backlight” panel.
TIP
Usaidizi wa kutekeleza amri ya sudo ed-ddc-ui kwenye dirisha la terminal ili kufungua paneli ya "EDATEC Backlight".
Raspberry Pi OS (Lite)
Adjusting backlight brightness via CLI on Raspberry Pi OS (Lite).
Maandalizi:
- ED-MONITOR-070C is properly connected to the Raspberry Pi host with normal display output.
- The Raspberry Pi host has stable network connectivity.
Hatua:
- Add EDATEC apt repository by executing the following commands sequentially in the terminal.
- Install the software toolkit
- Query current brightness level:
- Weka kiwango cha mwangaza:
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
Nyaraka / Rasilimali
 |
Teknolojia ya EDA ED-MONITOR-070C Uendeshaji na Udhibiti wa Kiwanda [pdf] Mwongozo wa Mtumiaji ED-MONITOR-070C Uendeshaji na Udhibiti wa Kiwanda, ED-MONITOR-070C, Uendeshaji na Udhibiti wa Viwanda, Uendeshaji na Udhibiti, na Udhibiti, Vidhibiti |