EDA TECHNOLOGY ED-IPC2430 Industrial Computer
Vipimo
- Model: ED-IPC2400
- Kulingana na: Raspberry Pi CM4
- RAM and eMMC options available
- Models: ED-IPC2410, ED-IPC2420, ED-IPC2430
- Interfaces: HDMI, USB, Ethernet, RS232, RS485
- Network Connectivity: Wi-Fi, Ethernet
- Integrated: RTC, EEPROM, encryption chip
- Application: Industrial control and IoT
Vifaa Vimekwishaview
The ED-IPC2400 series is designed for industrial applications based on the Raspberry Pi CM4. Different models with varying RAM and eMMC configurations are available to suit different user needs.
Orodha ya Ufungashaji
The packing list includes all necessary components to set up and operate the ED-IPC2400 series.
Muonekano
The appearance of the device includes various interfaces such as HDMI, USB, Ethernet, RS232, and RS485. Each panel has specific functions and definitions.
Jopo la mbele
The front panel includes indicators and ports for power, system status, DC input, HDMI, Ethernet, and UART communication.
Kazi za Jopo la Mbele
- Kiashiria cha Nguvu: Huonyesha hali ya nguvu ya kifaa
- System Status Indicator: Displays device working status
- DC Input: Supports 9V~28V input
- HDMI Port: Supports 4K 60Hz display
- Ethernet Port: Provides network connectivity
- RS485 Ports: Used for third-party control equipment
- RS232 Port: For serial communication
- UART Port Indicator: Shows communication status
- User Indicator: Customizable status indicator
ED-IPC2400
Mwongozo wa Mtumiaji
na EDA Technology Co., Ltd iliyojengwa: 2025-08-01
ED-IPC2400
1 Mwongozo wa vifaa
Sura hii inatanguliza juu ya bidhaaview, orodha ya kufunga, mwonekano, kitufe, kiashirio na kiolesura.
1.1 Zaidiview
ED-IPC2400 series is an industrial computer based on Raspberry Pi CM4. According to different application scenarios and user needs, different specifications of RAM and eMMC computer systems can be selected.
· RAM can choose 1GB2GB4GB and 8GB. · eMMC can choose 8GB16GB and 32GB.
ED-IPC2400 series includes three models, ED-IPC2410, ED-IPC2420 and ED-IPC2430, which provide common interfaces such as HDMI, USB, Ethernet, RS232 and RS485, and support access to the network through Wi-Fi and Ethernet. It integrates RTC, EEPROM and encryption chip, providing the ease of use and reliability of the product, which is mainly used in industrial control and IOT.
1.2 Orodha ya Ufungashaji
· 1x ED-IPC2400 Unit · [optional Wi-Fi/BT version] 1x 2.4GHz/5GHz Wi-Fi/BT Antenna
1.3 Mwonekano
Tunakuletea vipengele na ufafanuzi wa violesura kwenye kila paneli.
1.3.1 Jopo la mbele
Tunakuletea aina na ufafanuzi wa kiolesura cha paneli ya mbele.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2410
ED-IPC2400
HAPANA.
Ufafanuzi wa Kazi
1
1 x kiashiria cha nguvu nyekundu, ambacho hutumika kuangalia hali ya kuwasha kifaa na kuzima.
2
1 x kiashiria cha hali ya mfumo wa kijani, ambayo hutumiwa kuangalia hali ya kufanya kazi ya kifaa.
3
1 x DC input, DC Jack connector. It supports 9V~28V input.
1 x HDMI port, type A connector, which is compatibles with HDMI2.0 standard and supports 4K 60Hz. It 4
inasaidia kuunganisha kionyesho.
1 x 10/100/1000M adaptive ethernet port, RJ45 connector, with led indicator. It can be used to access the 5
mtandao.
2 x RS485 ports, 6-Pin 3.5mm spacing phoenix terminal, which is used to connect the third-party control 6
vifaa.
2 x RS485 ports, 4-Pin 3.5mm spacing phoenix terminal, which is used to connect the third-party control 7
vifaa.
1 x RS232 port, DB9 male terminal, using pins 2, 3 and 5 of the terminal, the corresponding signal is 8
defined as RX/TX/GND.
9
5 x green UART port indicator, which is used to check the communication status of UART port.
10
1 x kiashiria cha kijani cha mtumiaji, mtumiaji anaweza kubinafsisha hali kulingana na programu halisi.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2420
ED-IPC2400
HAPANA.
Ufafanuzi wa Kazi
1
1 x kiashiria cha nguvu nyekundu, ambacho hutumika kuangalia hali ya kuwasha kifaa na kuzima.
2
1 x kiashiria cha hali ya mfumo wa kijani, ambayo hutumiwa kuangalia hali ya kufanya kazi ya kifaa.
3
1 x DC input, DC Jack connector. It supports 9V~28V input.
1 x HDMI port, type A connector, which is compatibles with HDMI2.0 standard and supports 4K 60Hz. It 4
inasaidia kuunganisha kionyesho.
1 x 10/100/1000M adaptive ethernet port, RJ45 connector, with led indicator. It can be used to access the 5
mtandao.
1 x RS485 port, 1 x RS232 port, 6-Pin 3.5mm spacing phoenix terminal, which is used to connect the third6
party control equipment.
2 x RS485 ports, 4-Pin 3.5mm spacing phoenix terminal, which is used to connect the third-party control 7
vifaa.
1 x RS232 port, DB9 male terminal, using pins 2, 3 and 5 of the terminal, the corresponding signal is 8
defined as RX/TX/GND.
9
5 x green UART port indicator, which is used to check the communication status of UART port.
10
1 x kiashiria cha kijani cha mtumiaji, mtumiaji anaweza kubinafsisha hali kulingana na programu halisi.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2430
ED-IPC2400
HAPANA.
Ufafanuzi wa Kazi
1
1 x kiashiria cha nguvu nyekundu, ambacho hutumika kuangalia hali ya kuwasha kifaa na kuzima.
2
1 x kiashiria cha hali ya mfumo wa kijani, ambayo hutumiwa kuangalia hali ya kufanya kazi ya kifaa.
3
1 x DC input, DC Jack connector. It supports 9V~28V input.
1 x HDMI port, type A connector, which is compatibles with HDMI2.0 standard and supports 4K 60Hz. It 4
inasaidia kuunganisha kionyesho.
1 x 10/100/1000M adaptive ethernet port, RJ45 connector, with led indicator. It can be used to access the 5
mtandao.
2 x RS232 ports, 6-Pin 3.5mm spacing phoenix terminal, which is used to connect the third-party control 6
vifaa.
2 x RS485 ports, 4-Pin 3.5mm spacing phoenix terminal, which is used to connect the third-party control 7
vifaa.
1 x RS232 port, DB9 male terminal, using pins 2, 3 and 5 of the terminal, the corresponding signal is 8
defined as RX/TX/GND.
9
5 x green UART port indicator, which is used to check the communication status of UART port.
10
1 x kiashiria cha kijani cha mtumiaji, mtumiaji anaweza kubinafsisha hali kulingana na programu halisi.
1.3.2 Paneli ya Nyuma
Tunakuletea aina na ufafanuzi wa kiolesura cha paneli ya nyuma.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
HAPANA.
Ufafanuzi wa Kazi
1
1 x DIN-rail bracket, install ED-IPC2400 Unit on the DIN-rail through the bracket.
2
1 x Micro-SD card slot, it supports the installation of SD card for storing user data.
1.3.3 Paneli ya Upande
Tunakuletea aina na ufafanuzi wa violesura vya paneli za pembeni.
HAPANA.
Ufafanuzi wa Kazi
1
1 x Kitufe cha kuweka upya, kitufe kilichofichwa, bonyeza kitufe ili kuanzisha upya kifaa.
2
1 x USB 2.0 port, type A connector, each channel supports up to 480Mbps.
3
2 x USB 3.0 bandari, aina ya kiunganishi A, kila chaneli inaweza kutumia hadi 5Gbps.
4
Mlango wa antena wa 1 x Wi-Fi/BT, kiunganishi cha SMA, ambacho kinaweza kuunganisha kwenye antena ya Wi-Fi/BT.
Kitufe cha 1.4
ED-IPC2400 series device includes a RESET button, which is a hidden button, and the silkscreen on the case is “RESET”. Pressing the RESET button will reset the device.
1.5 Kiashiria
Introducing the various statuses and meanings of indicators contained in ED-IPC2400 series device.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
Kiashiria
Hali Imewashwa
PWR
Blink
Imezimwa
ACT
Kupepesa Kumezimwa
On
USER Off
Yellow indicator for Ethernet port Green indicator for Ethernet port COM1~COM5
On Blink Off On Blink Off On/Blink
Imezimwa
Description The device has been powered on. Power supply of the device is abnormal, please stop the power supply immediately. The device is not powered on. The system started successfully and is reading and writing data. The device is not powered on or does not read and write data. User can customize a status according to actual application. The device is not powered on or not defined by the user, and the default status is off. The data transmission is abnormal. Data is being transmitted over the Ethernet port. The Ethernet connection is not set up. The Ethernet connection is in the normal state. The Ethernet connection is abnormal. The Ethernet connection is not set up. Data is being transmitted. The device is not powered on or there is no data transmission.
1.6 Kiolesura
Tunakuletea ufafanuzi na utendakazi wa kila kiolesura katika bidhaa.
Slot ya Kadi ya SD ya 1.6.1
Skrini ya hariri kwenye kipochi cha nafasi ya kadi ya SD ni ” ", ambayo hutumika kusakinisha kadi ya SD kwa kuhifadhi data ya mtumiaji.
1.6.2 Kiolesura cha Ugavi wa Nguvu
The ED-IPC2400 series device includes one power input, DC Jack connector. It supports 9V~28V input, and the silkscreen of port is “DC IN”.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
1.6.3 Kiolesura cha RS485/RS232
ED-IPC2400 series devices include 2~4 RS485 ports and 1~3 RS232 ports. Different product models correspond to different numbers of RS485 and RS232 ports:
· ED-IPC24104 x RS4851x RS232 · ED-IPC24203 x RS4852x RS232 · ED-IPC24302 x RS4853 x RS232
The silkscreen of RS485 single port is “GND/A/B”. The silkscreen of RS232 single port is “GND/ TX/RX”, and the spacing of the terminals is 3.5mm.
Pin Definition – DB9 Terminal
Terminal pins are defined as follows:
Pin ID 1 2 3 4 5 6 7 8 9
Pin Name NC RS232_TXD0 RS232_RXD0 NC GND NC NC NC NC
Majina ya pini ya CM4 yanayolingana na kiolesura cha RS232 ni kama ifuatavyo:
Signal RS232_TXD0 RS232_RXD0
CM4 GPIO Jina GPIO14 GPIO15
CM4 Pin Out UART0_TXD UART0_RXD
Pin Definition – Phoenix Terminal Terminal pins are defined as follows:
Pini kitambulisho 1 2 3
Pin Name RS485-4_A RS485-2_A RS485-4_B
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
4
RS485-2_B
5
GND
6
GND
7
RS232-5_TX or RS485-5_A
8
RS232-3_TX or RS485-3_A
9
RS232-5_RX or RS485-5_B
10
RS232-3_RX or RS485-3_B
The pin names of CM4 corresponding to RS485/RS232 interface are as follows:
Signal RS485-4_A RS485-2_A RS485-4_B RS485-2_B RS232-5_TX or RS485-5_A RS232-3_TX or RS485-3_A RS232-5_RX or RS485-5_B RS232-3_RX or RS485-3_B
CM4 GPIO Jina GPIO8 GPIO12 GPIO9 GPIO13 GPIO4 GPIO0 GPIO5 GPIO1
CM4 Pin Out UART4_TXD UART5_TXD UART4_RXD UART5_RXD UART3_TXD UART2_TXD UART3_RXD UART2_RXD
Kuunganisha Cables Mchoro wa Kiratibu wa waya za RS485 ni kama ifuatavyo:
ED-IPC2400
Schematic diagram of RS232 wires is as follows:
usanidi wa upinzani wa terminal wa RS485
ED-IPC2400 device includes 2~4 RS485 ports, 120R jumper resistor is reserved between A and B of RS485 line, inserting jumper cap can enable this jumper resistor. The 120R termination resistor
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
function is disabled when the jumper cap is not connected in the default state. The positions of the jumper resistor in the PCBA is as follows: J24, J25, J26 and J27 (red box location).
The corresponding relationship between 120R terminal resistance and serial port is as follows:
Mahali pa PCBA J24 J25 J26 J27
Corresponding COM port COM2 COM4 COM3 COM5
Mahali maalum ya COM inayolingana
TIP
Unahitaji kufungua kesi ya kifaa view nafasi ya 120R jumper resistor. Kwa utendakazi wa kina, tafadhali rejelea 2.1.1 Fungua Kipochi cha Kifaa.
1.6.4 1000M Kiolesura cha Ethaneti
The ED-IPC2400 device includes one adaptive 10/100/1000M Ethernet port, and the silkscreen is
” “. The connector is RJ45, which is used to access the Ethernet. The pins corresponding to the terminals are defined as follows:
Pini kitambulisho 1 2 3
Pin Name TX4TX4+ TX3-
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
4
TX3+
5
TX2-
6
TX2+
7
TX1-
8
TX1+
1.6.5 Kiolesura cha HDMI
ED-IPC2400 series device includes one HDMI port, the silkscreen is “HDMI”. The connector is type A HDMI, which can connect to an HDMI display and supports up to 4Kp60.
1.6.6 USB 2.0 Kiolesura
ED-IPC2400 series device includes one USB2.0 port, the silkscreen is ” “. The connector is type A USB, which can connect to standard USB 2.0 peripherals and supports up to 480Mbps.
1.6.7 USB 3.0 Kiolesura
ED-IPC2400 series device includes 2 USB3.0 ports, the silkscreen is ” “. The connector is type A USB, which can connect to standard USB 3.0 peripherals and supports up to 5Gbps.
1.6.8 Kiolesura cha Antena
The ED-IPC2400 series device includes up to one SMA antenna port, the silkscreen is “WiFi/BT” and it can be connected to the Wi-Fi/BT antenna.
1.6.9 Kiolesura cha Motherboard
Introducing the interfaces reserved in the ED-IPC2400 series device, which can be obtained only after the device case is opened( For detailed operations, please refer to 2.1.1 Open Device Case ), and can be expanded according to actual needs.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
HAPANA.
Kazi
1
5V 1A Pato
2
USB 2.0 Pin Header
1.6.9.1 5V 1A Pato
The motherboard of ED-IPC2400 series device includes an extended 5V 1A power output port with 3-Pin 2.0mm spacing white WTB connector, which is reserved for the extended LCD screen to supply power. The pins are defined as follows:
Pini kitambulisho 1 2 3
Pin Name GND 5V GND
1.6.9.2 USB 2.0 Kiolesura
The motherboard of ED-IPC2400 series device includes an extended USB 2.0 Pin Header with 5Pin 1.5mm spacing WTB connector. It is used to expand a USB 2.0 interface, the pins are defined as follows:
Kitambulisho cha siri 1 2 3 4
Pin Name VBUS USB_DM USB_DP GND
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
5
GND
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
2 Kufunga Vipengele
Sura hii inaeleza jinsi ya kusakinisha vipengele vya hiari.
2.1 Opening and closing the device case
If the user needs to open the device case, refer to the following to do so.
2.1.1 Open device case
Preparation: A cross screwdriver has been prepared. Steps: 1. Pull out the default configuration of phoenix connector. 2. Use a screwdriver to loosen two M3 screws on two sides counterclockwiseas shown in the
takwimu hapa chini.
3. Remove the front cover to the right, as shown in the figure below.
4. Use a screwdriver to loosen four M2.5 screws and one grounding screw on two sides counterclockwise, as shown in the figure below.
5. Remove the upper cover upward and turn it to the antenna port side, as shown in the figure below.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
2.1.2 Funga Kipochi cha Kifaa
Preparation: A cross screwdriver has been prepared. Steps: 1. Turn the upper cover downwards, align the ports on PCBA with the ports on each side panel
and close the upper cover.
2. Align the screw holes on the upper and side panels, and use a screwdriver to tighten four M2.5 screws and one grounding screw on two sides clockwise, as shown in the following figure.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
3. Align the ports on PCBA with the ports on the front panel, insert the front cover, and then use a screwdriver to fasten two M3 screws clockwise, as shown in the following figure.
4. Plug in the default configuration of phoenix connector.
2.2 Installing Other Components
If the selected ED-IPC2400 series device includes Wi-Fi functions, the antenna need to be installed before using the device.
2.2.1 Weka Antena
Preparation: The corresponding antennas have been obtained from the packaging box. Steps: 1. Locate the antenna port where the antenna is to be installed, as shown in the figure below.
2. Align the ports on both sides of the device and the antenna, and tighten them clockwise to ensure that they will not fall off.
2.2.2 Sakinisha Kadi Ndogo ya SD
Maandalizi:
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
The Micro SD card to be used has been obtained. Steps: 1. Use a cross screwdriver to loosen 5 screws on the DIN-rail bracket counterclockwise and
remove the default DIN-Rail bracket. As shown in the figure below.
2. Locate the Micro SD card slot where the Micro SD is to be installed, as shown in the red box below.
3. Ingiza kadi ndogo ya SD na upande wa mguso chini kwenye sehemu ya kadi inayolingana, na usikie sauti kuashiria kuwa usakinishaji umekamilika.
4. Install the DIN-Rail bracket onto the device case.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
3 Kusakinisha Kifaa
Sura hii inatanguliza jinsi ya kusakinisha kifaa.
3.1 Ufungaji wa DIN-Reli
When the ED-IPC2400 series device leaves the factory, the DIN-rail bracket is installed as standard by default. Steps: 1. Face the side of the DIN-rail bracket to the rail to be installed, and the upper side of the bracket
is sleeved on the upper side of the rail.
2. Press down the buckle on the lower side of the DIN-rail bracket until the bracket can be buckled on the rail, and the installation is completed.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
4 Kuanzisha Kifaa
Sura hii inatanguliza jinsi ya kuunganisha nyaya na kuwasha kifaa.
4.1 Kuunganisha nyaya
Sehemu hii inaelezea jinsi ya kuunganisha nyaya. Maandalizi:
· Nyenzo kama vile onyesho, kipanya, kibodi na adapta ya nishati ambayo inaweza kutumika kwa kawaida imekuwa tayari.
· Mtandao ambao unaweza kutumika kawaida. · Pata kebo ya HDMI na kebo ya mtandao ambayo inaweza kutumika kawaida. Mchoro wa mpangilio wa nyaya za kuunganisha: Tafadhali rejelea Violesura 1.6 kwa ufafanuzi wa pini ya kila kiolesura na mbinu mahususi ya kuunganisha nyaya.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
4.2 Kuanzisha Mfumo Kwa Mara ya Kwanza
ED-IPC2400 series device has no switching power supply. After the power supply is connected, the system will start.
· Kiashiria chekundu cha PWR kimewashwa, kikionyesha kuwa kifaa kimewashwa kawaida. · Kiashirio cha kijani cha ACT kinapepesa macho, kuashiria kuwa mfumo umeanza kawaida, na kisha
nembo ya Raspberry Pi itaonekana kwenye kona ya juu kushoto ya skrini.
TIP Jina la mtumiaji chaguo-msingi ni pi , Nenosiri chaguo-msingi ni raspberry.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
4.2.1 Raspberry Pi OS (Desktop)
Ikiwa toleo la Desktop la mfumo limewekwa wakati bidhaa inaondoka kwenye kiwanda, baada ya kifaa kuanza, itaingia moja kwa moja kwenye eneo-kazi, kama inavyoonyeshwa kwenye takwimu ifuatayo.
4.2.2 Raspberry Pi OS (Lite)
Ikiwa toleo la Lite la mfumo limesakinishwa kiwandani, jina la mtumiaji chaguo-msingi litatumika kuingia kiotomatiki baada ya kifaa kuwashwa, na nenosiri chaguo-msingi ni raspberry. Kielelezo kifuatacho kinaonyesha kuwa mfumo umeanza kawaida.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
5 Mfumo wa Kusanidi
Sura hii inatanguliza jinsi ya kusanidi mfumo.
5.1 Kupata IP ya Kifaa
Inatafuta IP ya Kifaa
5.2 Kuingia kwa Mbali
Kuingia kwa mbali
5.3 Kusanidi Vifaa vya Kuhifadhi
Inasanidi Vifaa vya Kuhifadhi
5.4 Kusanidi IP ya Ethaneti
Inasanidi IP ya Ethaneti
5.5 Kuweka Wi-Fi (Si lazima)
Inasanidi Wi-Fi
5.6 Kusanidi Bluetooth (Si lazima)
Inasanidi Bluetooth
5.7 Kusanidi Buzzer
Buzzer controlled by GPIO6. · Turn on the buzzer:
raspi-gpio seti 6 op dh
· Turn off the buzzer:
raspi-gpio seti 6 op dl
ED-IPC2400
sh sh
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
5.8 Kusanidi RTC
Inasanidi RTC
5.9 Kusanidi Mlango wa Siri
Sura hii inatanguliza njia ya usanidi ya RS232 na RS485.
5.9.1 Kusakinisha zana ya picocom
Katika mazingira ya Linux, unaweza kutumia zana ya picocom kutatua bandari za mfululizo RS232 na RS485. Tekeleza amri ifuatayo ili kusakinisha zana ya picocom.
sh sudo apt-get install picocom
5.9.2 Inasanidi RS232
ED-IPC2400 includes 1~3 RS232 ports with their corresponding COM ports and device files kama ifuatavyo:
ED-IPC2410
Idadi ya RS232 Bandari 1
Sambamba COM Port COM1
Kifaa Kinacholingana File /dev/com1
ED-IPC2420
Idadi ya RS232 Bandari 2
Bandari ya COM inayolingana COM1, COM5
Kifaa Kinacholingana File /dev/com1, /dev/com5
ED-IPC2430
Idadi ya RS232 Bandari 3
Bandari ya COM inayolingana COM1, COM3, COM5
Kifaa Kinacholingana File /dev/com1, /dev/com3, /dev/com5
Maandalizi:
The RS232 port of ED-IPC2400 has been connected with external device.
Hatua:
1. Execute the following command to open the serial port com1, and configure the serial port baud rate to 115200.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
picocom -b 115200 /dev/com1
ED-IPC2400
sh
2. Ingiza amri inavyohitajika ili kudhibiti kifaa cha nje.
5.9.3 Inasanidi RS485
ED-IPC2400 includes 4 RS485 ports, and the corresponding COM ports and device files ni kama ifuatavyo:
ED-IPC2410
Idadi ya RS485 Bandari 4
Bandari ya COM inayolingana COM2, COM3, COM4, COM5
Kifaa Kinacholingana File /dev/com2, /dev/com3, /dev/com4, /dev/com5
ED-IPC2420
Idadi ya RS485 Bandari 3
Bandari ya COM inayolingana COM2, COM3, COM4
Kifaa Kinacholingana File /dev/com2, /dev/com3, /dev/com4
ED-IPC2430
Idadi ya RS485 Bandari 2
Bandari ya COM inayolingana COM2, COM4
Kifaa Kinacholingana File /dev/com2, /dev/com4
Preparation: The RS485 port of ED-IPC2400 has been connected with external devices. Steps: 1. Execute the following command to open the serial port com2, and configure the serial port baud
bei ya 115200.
sh picocom -b 115200 /dev/com2
2. Ingiza amri inavyohitajika ili kudhibiti vifaa vya nje.
5.10 Kusanidi Kiashiria cha MTUMIAJI
USER indicator controlled by GPIO10. · Light up the USER indicator:
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
raspi-gpio seti 10 op dl
· Turn off the USER indicator:
raspi-gpio seti 10 op dh
ED-IPC2400
sh
sh
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
6 Kusakinisha Mfumo wa Uendeshaji (si lazima)
Kifaa kinasafirishwa na mfumo wa uendeshaji kwa chaguo-msingi. Ikiwa OS imeharibiwa wakati wa matumizi au mtumiaji anahitaji kuchukua nafasi ya OS, ni muhimu kupakua tena picha ya mfumo unaofaa na kuiweka. Kampuni yetu inasaidia kusakinisha OS kwa kusakinisha Raspberry Pi OS ya kawaida kwanza, na kisha kusakinisha kifurushi cha Firmware.
Sehemu ifuatayo inaelezea utendakazi mahususi wa upakuaji wa picha, kuwaka kwa eMMC na usakinishaji wa vifurushi vya Firmware.
6.1 Kupakua Mfumo wa Uendeshaji File
Unaweza kupakua Raspberry Pi OS rasmi inayolingana file kulingana na mahitaji yako halisi, njia ya upakuaji imeorodheshwa hapa chini:
OS
Pakua Njia
Raspberry Pi OS(Desktop) 64-bit-bookworm (Debian 12)
https://downloads.raspberrypi.com/raspios_arm64/images/ raspios_arm64-2024-07-04/2024-07-04-raspios-bookworm-arm64.img.xz (https://downloads.raspberrypi.com/raspios_arm64/images/ raspios_arm64-2024-07-04/2024-07-04-raspios-bookworm-arm64.img.xz)
Raspberry Pi OS(Lite) 64-bit-bookworm (Debian 12)
https://downloads.raspberrypi.com/raspios_lite_arm64/images/ raspios_lite_arm64-2024-07-04/2024-07-04-raspios-bookworm-arm64lite.img.xz (https://downloads.raspberrypi.com/raspios_lite_arm64/images/ raspios_lite_arm64-2024-07-04/2024-07-04-raspios-bookworm-arm64lite.img.xz)
Raspberry Pi OS(Desktop) 32-bit-bookworm (Debian 12)
https://downloads.raspberrypi.com/raspios_armhf/images/ raspios_armhf-2024-07-04/2024-07-04-raspios-bookworm-armhf.img.xz (https://downloads.raspberrypi.com/raspios_armhf/images/ raspios_armhf-2024-07-04/2024-07-04-raspios-bookworm-armhf.img.xz)
Raspberry Pi OS(Lite) 32-bit-bookworm (Debian 12)
https://downloads.raspberrypi.com/raspios_lite_armhf/images/ raspios_lite_armhf-2024-07-04/2024-07-04-raspios-bookworm-armhflite.img.xz (https://downloads.raspberrypi.com/raspios_lite_armhf/images/ raspios_lite_armhf-2024-07-04/2024-07-04-raspios-bookworm-armhflite.img.xz)
6.2 Kumulika kwa eMMC
Inashauriwa kutumia zana rasmi za Raspberry Pi. Njia za upakuaji ni kama ifuatavyo: · Raspberry Pi Imager: https://downloads.raspberrypi.org/imager/imager_latest.exe (https:// downloads.raspberrypi.org/imager/imager_latest.exe)
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
· Muundo wa Kadi ya SD: https://www.sdcardformatter.com/download/ (https:// www.sdcardformatter.com/download/)
· Rpiboot: https://github.com/raspberrypi/usbboot/raw/master/win32/rpiboot_setup.exe (https:// github.com/raspberrypi/usbboot/raw/master/win32/rpiboot_setup.exe)
Maandalizi:
· The downloading and installation of the official tools to the computer have been completed. · A USB-A to USB-A cable has been prepared. · The OS file imepatikana.
Hatua:
Hatua zinaelezewa kwa kutumia mfumo wa Windows kama wa zamaniample.
1. When the device is not powered on, press and hold the PROGRAMMING button while connecting the power cord and USB flashing cable (USB-A to USB-A cable). Then, power up the device (release the PROGRAMMING button after powering up).
· Connecting to USB flashing cable: One end is connected to the USB 2.0 port on the device, and the other end is connected to the USB port on the PC.
· Connecting to power cord: One end is connected to the DC jack connector on the device, and the other end is connected to the external power supply.
2. Open rpiboot tool to automatically convert the drive to a letter
3. Baada ya kukamilika kwa barua ya gari, barua ya gari itatokea kwenye kona ya chini ya kulia ya kompyuta.
4. Fungua Umbizo la Kadi ya SD, chagua herufi ya kiendeshi iliyoumbizwa, na ubofye "Umbiza" kwenye sehemu ya chini ya kulia ili umbizo.
5. Katika kisanduku ibukizi, chagua "Ndiyo". 6. Wakati uumbizaji umekamilika, bofya "Sawa" kwenye kisanduku cha haraka. 7. Funga Umbizo la Kadi ya SD. 8. Fungua Raspberry Pi Imager, chagua "CHAGUA OS" na uchague "Tumia Maalum" kwenye dirisha ibukizi.
kidirisha.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
9. Kwa mujibu wa haraka, chagua OS file chini ya njia iliyoainishwa na mtumiaji na urudi kwenye ukurasa kuu.
10. Bonyeza "CHAGUA HIFADHI", chagua kifaa chaguo-msingi kwenye kiolesura cha "Hifadhi", na urejee kwenye ukurasa kuu.
11. Bofya "Inayofuata", chagua "HAPANA " kwenye dirisha ibukizi "Tumia ubinafsishaji wa Mfumo wa Uendeshaji?" kidirisha.
12. Chagua "NDIYO" kwenye kidirisha cha "Onyo" ibukizi ili kuanza kuandika picha.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
13. Baada ya uandishi wa OS kukamilika, the file itathibitishwa.
14. Baada ya uthibitishaji kukamilika, bofya "ENDELEA" kwenye kisanduku ibukizi "Andika Umefaulu". 15. Funga Raspberry Pi Imager, ondoa kebo ya USB na uwashe kifaa tena.
6.3 Kuweka Kifurushi cha Firmware
After you have finished flashing to eMMC on ED-IPC2400 Series, you need to configure the system by adding edatec apt source and installing firmware package to make the system work. The following is an example of Debian 12 (bookworm) desktop version and ED-IPC2410.
Maandalizi:
· Kumulika kwa eMMC ya Raspberry Pi standard OS (bookworm) imekamilika. · Kifaa kimewashwa kawaida na usanidi unaofaa wa kuwasha umekamilika.
Hatua:
1. Baada ya kifaa kuanza kawaida, tekeleza amri zifuatazo kwenye kidirisha cha amri ili kuongeza chanzo cha edatec apt na kusakinisha kifurushi cha programu.
sh curl -s https://apt.edatec.cn/bsp/ed-install.sh | sudo bash -s ipc2410
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
ED-IPC2400
TIP If the product models are ED-IPC2420 and ED-IPC2430, the names of the Firmware packages are ipc2420 and ipc2430. 2. After the installation is complete, the system automatically reboots. 3. Execute the following command to check whether the firmware package is installed successfully.
sh dpkg -l | grep ed-
Matokeo katika picha hapa chini yanaonyesha kuwa kifurushi cha firmware kimewekwa kwa mafanikio.
TIP Ikiwa umesakinisha kifurushi kibaya cha programu dhibiti, unaweza kutekeleza sudo apt-get -purge remove kifurushi ili kukifuta, ambapo "kifurushi" ni jina la kifurushi.
Barua pepe: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Simu: +86-15921483028(Uchina) | +86-18217351262(Nje ya nchi)
Nyaraka / Rasilimali
 |
EDA TECHNOLOGY ED-IPC2430 Industrial Computer [pdf] Mwongozo wa Mtumiaji ED-IPC2410, ED-IPC2420, ED-IPC2430, ED-IPC2430 Industrial Computer, ED-IPC2430, Industrial Computer, Computer |