Buddy UG21.001 Autonomous Mobile Robot

Vipimo vya Bidhaa

• Jina la Bidhaa: CDaOCrtKeINBG lSaTnATcIOhNe GuUisdeer UGtuiliisdaeteEuNr VV21..001
• Yaliyomo kwenye Kifurushi: Charging station, Fastener installation guide, 1:1 scale template, 2 fixing screws, and plate for wall-mount

Maagizo ya Matumizi ya Bidhaa

Mounting the Base on the Wall

• Adhesive Bonding
  1. Apply double-sided tape to the base.
  2. Hang the base from the attachment to the charging station.
  3. Remove the double-sided tape protection and press the assembly firmly against the wall.
• Kuweka screw
  1. Cut out the template provided.
  2. Apply the template to the baseboard edge.

Station Connection
Connect the station to the power supply supplied with the robot.

Buddy Menu Configuration
Follow the menu options on your device to configure settings related to the Buddy system.

Reloading Process

• Triggering the Reloading Process
  Initiate the reloading process as outlined in the user manual.
• Exit from Recharging Process
  Follow the instructions to safely exit from the recharging process.
• Onyo
  Ensure that charging station markers are always visible and that the robot is positioned correctly for recharging.

Dock the Robot from MyBuddyApp

• On TeleBuddy
  1. Double-check settings on Companion Menu -> Charging Station -> Enabled.
  2. Launch TeleBuddy (V1.2.18 or higher).
  3. Enable automatic unhooking.
• On MyBuddyApp
  1. Download MyBuddyApp.
  2. Launch MyBuddyApp on your Tablet (V2.3.8 or higher).
  3. Go to the Settings menu and select Advanced settings.
  4. Activate Charging Station.
  5. Drive the robot to position it in front of the Charging Station and follow the on-screen instructions.
  6. Press the Docking button in the MyBuddyApp Menu.

MAUDHUI

ITEMS SUPPLIED WITH THE CHARGING STATION PACKAGE

MOUNTING THE BASE ON THE WALL

ADHESIVE BONDING

1. Apply double-sided tape
2. Hang the base from the attachment to the charging station
3. Remove the double-sided tape protection and press the assembly firmly against the wall.

   

KUWEKA SKARIFU

• Kata kiolezo
  
• Apply to the baseboard edge.
  

STATION CONNECTION

Connect the station to the power supply supplied with the robot.

BUDDY MENU CONFIGURATION

1. Access the Buddy menu
2. Go to the «Companion» tab
3. Activate the «Base station» button

   

RELOADING PROCESS

TRIGGERING THE RELOADING PROCESS

1. Battery level down to 20%
   The robot automatically launches the search mission for the recharge
2. The user says one of the following voice commands :
   • «GO TO THE DOCKING STATION»,
   • «GO TO THE CHARGING STATION»,
   • «GO (RECHARGE | RECHARGING)»,
   • «GO (CHARGE | CHARGING)»,
   • «GO HOME»,
   • «GO TO YOUR HOUSE»

EXIT FROM RECHARGING PROCESS

1. Battery level reaches 100%. The robot automatically exits the Docking station.
2. If the battery level is less than 100% give the Voice Command « Stop charging.»

ONYO
Charging station markers must always remain visible. The robot must be less than 4m from the Docking, with unobstructed access. The area between the robot and the recharging station must be clear of obstacles, chair legs, and table legs. The parking area must be greater (height and withan dth) robot’st’st dimensions.

DOCK THE ROBOT FROM MYBUDDYAPP

ON TELEBUDDY
Double-check the setting:
Companion Menu -> Charging Station -> Enabled

ON MYBUDDYAPP

• Launch MyBuddyApp on your Tablet (V2.3.8 or higher)

  

• Drive the robot to position it in front of the Charging Station.
  You must be able to see at least one of the Docking Station’s QR codes.

  

TAARIFA ZA MAWASILIANO

If you wish to contact us for further information, please refer to the following address:

• MSAADA service-client@buddytherobot.com
• HABARI YA JUMLA info@bluefrogrobotics.com

Nyaraka / Rasilimali

Buddy UG21.001 Autonomous Mobile Robot [pdf] Mwongozo wa Mtumiaji UG21.001, UG21.001 Autonomous Mobile Robot, UG21.001, Autonomous Mobile Robot, Mobile Robot

Marejeleo

• Mwongozo wa Mtumiaji