Kiolesura cha Kuhifadhi Kamera ya AXBUC-VW92
“
Vipimo:
- Product Name: AXBUC-VW92 Backup Camera Retention Interface
- Compatibility: Select Volkswagen/Skoda Models 2008-2015 with
RNS510 (MFD3), RNS315, Columbus (Skoda), or RCD510 (with 26-pin
kiunganishi)
Maagizo ya matumizi ya bidhaa:
Hatua za Ufungaji:
- Connect the Ground wire from the VW92 to the aftermarket
radio’s ground wire. - Connect the Yellow wire from the VW92 to the Yellow wire of
your aftermarket radio. - Connect the Purple wire to the reverse trigger from your
vehicle or interface. - Chomeka kebo ya Video ya CAM OUT kwenye sehemu ya nyuma view pembejeo ya kamera
of your aftermarket radio. - Chomeka kiunganishi Nyeupe kwenye kisanduku cha kiolesura.
- Plug in the vehicle connector and perform a test.
Mipangilio ya Kubadilisha Dip:
Refer to the instructions included with the product for dip
badilisha mipangilio.
Maswali Yanayoulizwa Mara kwa Mara:
Q: What vehicles are compatible with the AXBUC-VW92 Backup
Camera Retention Interface?
A: The interface is compatible with various Volkswagen and Skoda
models ranging from 2008 to 2015. Refer to the user manual or visit
AxxessInterfaces.com for specific applications.
Q: Why should I disconnect the negative battery terminal before
ufungaji?
A: Disconnecting the battery terminal ensures safety during
installation, especially when dealing with sensitive electrical
connections like airbag indicators. Always follow safety
tahadhari zinazotolewa katika mwongozo.
"`
AXBUC-VW92
MAELEKEZO YA KUFUNGA
Backup Camera Retention Interface Fits Select Volkswagen/Skoda Models 2008-2015*
* For vehicles equipped with RNS510 (MFD3), RNS315, Columbus (Skoda), or RCD510 (with 26-pin connector)
TABLE OF CONTENTS Connections: BLK-AXBUC-VW92………………………2 Installing the Interface……………………………………3 Dip Switch Settings…………………………………………3
VIPENGELE VYA INTERFACE
· Retains the OEM camera to an aftermarket radio · Plug-and-play, no cutting of wires required · For vehicles equipped with RNS510 (MFD3), RNS315, Columbus
(Skoda), or RCD510 (with 26-pin connector)
VIFAA VINAVYOHITAJI
· Zana ya kutengenezea na viungio, au bunduki ya solder, solder, na kupunguza joto · Tepu · Kikata waya
· Vifungo vya zip
INTERFACE COMPONENTS · AXBUC-VW92 interface
· BLK-AXBUC-VW92 harness
NOTE: If your vehicle has a motorized OE camera door or active guidelines, you will need an interface that can enable the camera door to open, the AXBUC-VW2 will not retain these function. The AXBUC-VW2 will only retain the camera.
MAOMBI
Volkswagen Amarok ……………………………………..2010-2014 EOS ………………………………………….. 2009-2014 Golf …………………………………………..2008-2014 Jetta …………………………………………2009-2014
Passat ………………………………………..2010-2015 Polo ………………………………………….2008-2014 Scirocco …………………………………….2008-2015 Tiguan ………………………………………. 2009-2015 Touran ……………………………………….2010-2015
Transporter ……………………………….2009-2014
Skoda Octavia ……………………………………..2009-2012 Superb ……………………………………..2008-2015
Tembelea AxxessInterfaces.com kwa maelezo zaidi kuhusu bidhaa na masasisho
vehicle specific applications
ATTENTION: Na ufunguo nje ya
kuwasha, tenganisha terminal hasi ya betri kabla ya kusakinisha bidhaa hii. Hakikisha kwamba miunganisho yote ya usakinishaji, hasa taa za viashiria vya mifuko ya hewa, zimechomekwa kabla ya kuunganisha betri tena au kuendesha kiwasho ili kujaribu bidhaa hii. KUMBUKA: Rejelea pia maagizo yaliyojumuishwa na redio ya soko la nyuma.
AxxessInterfaces.com
© COPYRIGHT 2025 METRA UMEME SHIRIKA
REV. 8/18/25 INSTAXBUC-VW92
Interface End View
ON VE 23 4
Dipswitch See Dipswitch Settings
kwenye ukurasa unaofuata
MAHUSIANO: BLK-AXBUC-VW92
Kiolesura
BLK-AXBUC-VW92
Redio ya Aftermarket
Mbele
(Vipengele vya redio yako vinaweza kutofautiana)
Nyuma View
AUX-IN Nyuma
Sehemu ndogo ya SWC
CAM OUT
Kiunganishi cha Gari
Radio Connections Black – Ground wire Yellow – Battery wire Purple – Reverse
2
KUWEKA MIPANGILIO YA INTERFACE & DIP SWITCH
· Connect the AXBUC-VW92 to the wiring harness in the vehicle located at the radio location (26-pin connector).
Installation Steps 1. Connect Ground wire from the VW92 to the aftermarket radio’s ground wire. 2. Connect the Yellow wire from the VW92 to the Yellow wire of your aftermarket radio. 3. Purple is a Reverse input, connect the reverse trigger from your vehicle or interface to
this wire. Do not connect this wire to the vehicle’s BCM for the reverse signal. VW uses PWM circuitry, if connected to the BCM, the backup camera will flicker while the vehicle is running. You must find a dedicated reverse signal or use an interface that provides a reverse output. 4. Plug in the CAM OUT Video cable into the rear view camera input of your aftermarket radio. 5. Plug in the White connector into the interface box. 6. Plug in the vehicle connector and test.
Dip Switch Settings If after the AXBUC-VW2 is installed your screen quickly flashes the backup camera, or is displaying a blank screen when you put the vehicle into reverse, you will need to adjust the dip switches on the side of the interface. If screen is blank or flashing while in reverse, try this sequence.
Interface End View
ON VE 23 4
ON VE Dipswitch Detail
23 4
Step 1 – Set Dip Switch 3 to OFF. – If not working go to step 2. Step 2 – Move all Dip Switches to OFF – If not working go to step 3. Step 3 – Flip Dip Switch 3 ON, leaving 1,2,4 OFF.
REV. 8/18/25 INSTAXBUC-VW92 3
AxxessInterfaces.com
AXBUC-VW92
MAELEKEZO YA KUFUNGA
Kuwa na shida? Tuko hapa kusaidia. Wasiliana na laini yetu ya Tech Support kwa:
386-257-1187
Au kupitia barua pepe kwa: techsupport@metra-autosound.com
Masaa ya Usaidizi wa Teknolojia (Saa Wastani ya Mashariki) Jumatatu - Ijumaa: 9:00 AM - 7:00 PM Jumamosi: 10:00 AM - 5:00 PM Jumapili: 10:00 AM - 4:00 PM
© COPYRIGHT 2025 METRA UMEME SHIRIKA
Metra inapendekeza mafundi walioidhinishwa na MECP
REV. 5/27/25 INSTAXBUC-VW92
Nyaraka / Rasilimali
 |
AXXESS AXBUC-VW92 Backup Camera Retention Interface [pdf] Mwongozo wa Maelekezo AXBUC-VW92 Backup Camera Retention Interface, AXBUC-VW92, Backup Camera Retention Interface, Camera Retention Interface, Retention Interface, Interface |