SW-MOTECH GPT.01.808.70000-B Top Case System

Product Information

Specifications

• Model Numbers: GPT.01.808.70000/B, GPT.01.808.16000/B, GPT.00.152.54100/B, ALK.00.733.15000/B, ALK.00.165.16503

Product Usage Instructions

Installation

1. Identify the appropriate model number for your product from the list provided.
2. Refer to the installation manual for step-by-step guidance on mounting and setup.
3. Ensure all components are securely attached following the provided instructions.

Operation

1. Once installed, power on the product using the designated power button or switch.
2. Follow the user manual to understand the different functionalities and settings available.
3. Adjust settings as needed to suit your preferences or requirements.

Maintenance

1. Regularly clean the product using a damp cloth to remove dust or dirt buildup.
2. Avoid using harsh chemicals or abrasive materials that may damage the product’s surface.
3. Check for any loose components or signs of wear and tear periodically.

FAQ

• Q: How do I find the correct model number for my product?
  • A: The model numbers can be found on the product label or packaging. Refer to the list provided in the specifications section to match your product.
• Q: What should I do if the product malfunctions?
  • A: If you encounter any issues with the product’s performance, refer to the troubleshooting section in the user manual for possible solutions. If problems persist, contact customer support for assistance.
• Q: Can I disassemble the product for cleaning?
  • A: It is not recommended to disassemble the product unless specified in the user manual. Use a damp cloth for regular cleaning and follow the maintenance guidelines provided.

STREET-RACK

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our website. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay\ attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the properfit of the product.

PRODUCT SPECIFIC INFORMATION

ATTENTION: The indicated maximum load is inclusive of the weight of the suitcase/luggage and adapter plate! The maximum vehicle load specified by the manufacturer must not be exceeded!

Parts List

Vote: a All measurements in millimeters.b The second number indicates the total quantity of the part in the delivery.c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table canbe used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

Open the bench.

Remove the original plastic caps, screws, and passenger grips on both sides of the vehicle.

Insert the plastic plugs (2) into the ends of the mounting struts (1), as shown in the detailed drawing. Attach the mounting struts (1) to the vehicle, as shown in the drawing.
ATTENTION: Pay attention to the different heights (h) of the spacers (4) and (5) shown in the drawing!
ATTENTION: Use liquid thread locker!
Do not fully tighten the screws yet.

Attach the luggage rack (6) onto the mounting struts (1), as shown in the drawing.
ATTENTION: Use a liquid thread locker!
Once all parts are evenly positioned without excess tension, tighten the screws (7) as specified.
Tighten the screws (3) with the manufacturer’s specified torque.

Adapter plate for STREET-RACK – TRAX ADV/ION/EVO

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our website. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

• PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
• MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
• FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

Parts List

* All measurements in millimeters. . ** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

Adapter plate for STREET-RACK Attach the shown parts to the adapter plate for STREET-RACK (1). Tighten the screws as specified in the parts list.
ATTENTION: To ensure the proper fit of your TRAX ADV/EVO/ION top case, adjust the latch hook (2) over the elongated holes (see detail drawing)! Make sure that the topcase’s latch engages properly when mounted!

Mounting the adapter plate on the STREET-RACK.

• Step [1]: Slide the adapter plate (1) with the two hooks into the holes of your STREET-RACK (sold separately).
• Step [2]: Press the adapter plate (1) slightly downwards and turn the fastener 90 degrees until it fits into place.
• Step [3]: Finally, press the lock firmly down as shown in the drawing. To release the adapter plate, simply pull the fastener upwards and turn it to the starting position.

TRAX ADVENTURE ALU-BOX

Thank you for choosing this premium product from SW-MOTECH. & Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our website. >> www.sw-motech.com Installation and/or maintenance of this product require good technical understanding. For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop. SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work. Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as a reference. This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Installed accessories can change driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Observe any country-specific legal or TUV regulations. If required, enter the installed parts into the vehicle documents with the appropriate inspection authority.

SECURITY

Please pay attention to the following information concerning the TRAX

ADVENTURE ALU-BOX:

The TRAX ADVENTURE ALU-BOX is designed exclusively for mounting on
SW-MOTECH QUICK-LOCK side carriers, QUICK-LOCK adapter plate STEEL-RACK adapter kit.
Modifications made to the cases will void any warranty. ATTENTION: Riding with TRAX ADVENTURE ALU-BOX may affect the motorcycle’s driving and braking performance.
ATTENTION: TRAX ADVENTURE ALU-BOXES M & L must be used in pairs. Make sure the weight is evenly distributed between left and right side cases.
DANGER: The maximum vehicle load defined by the vehicle manufacturer may NOT be exceeded. The maximum permissible load of the SW-MOTECH luggage rack side carrier may NOT be exceeded; make sure to take into account the dead weight of the product.
ATTENTION: Maximum load: Please refer to the mounting instructions of the SW-MOTECH luggage rack/side carrier. Maximum speed with mounted cases: 130 km/h (80 mph).
ATTENTION: Make sure that the TRAX ADVENTURE ALU-BOX is properly attached to the particular adapter and fully engaged to all four mounting points! ALL latches of the TRAX ADVENTURE ALU-BOX must be locked BEFORE riding with the TraX ® EVO / TRAX ADV lock cylinder set (sold separately) and remain closed while riding. Improperly mounted cases run the risk of detaching during transport.

CARE

To clean the TRAX ADVENTURE ALU-BOX, use warm, soapy water and a soft,clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high-pressure washer!

Parts List

The second number indicates the total quantity of the listed part in the delivery.

TECHNICAL DETAILS

• www.sw-motech.com

Please visit our webshop for application charts and compatible accessories.

LID AND LOCK CYLINDER SET

Open the lid

(TRAX ADV M / L / topcase)

1. Pull the latch of the lid upwards
2. and remove it from the latchbar.
3. Open the lid.

Insertion of the TraX ® EVO / TRAX ADV lock cylinder set *(TRAX ADV M / L / Topcase]

1. Insert the lock cylinders into the latches.
2. Secure the lock cylinders with the clamping plates.
   ATTENTION: Pay attention to the correct alignment of the clamping plates (as shown in the detail drawings).
3. Insert the keys into the lock cylinders; open or close the lock cylinder as shown in the schematic drawing.
   ATTENTION: Use for lubrication graphite powder ONLY!
   * Sold separately.

1. 

LID LIMITER

Mounting the lid limiters (TRAX ADV M / L / top case)

1. Open the lid. Attach the snap-fit (4) with the shown parts at the lidframe.
   Tighten the screws as specified in the parts list.
2. Attach the lid limiters (5) with the shown parts at the case frame.
   NOTE: Pay attention to left-right specifications for the limiters (in the driving direction). Tighten the screws as specified in the parts list. Press the lid limiters onto the snap-fits.
3. Before closing the lid for the first time, the lid limiters must be compressed as shown in the drawing. While closing the lid, make sure that the lid limiters are not pinched between lid and case.
4. To remove the lid from the case remove the lid limiters from the snap-fits first.

QUICK RELEASE FASTENER

Removing the lid (TRAX ADVENTURE M/ L)

1. Press the quick-release fastener down until it clicks into place and the button pops out.
2. Then remove the lid from the case.
   NOTE: If you have installed the lid limiters (5), they must be detached before removing the lid las).
3. Press the button of the quick-release fastener to lock the replaced lid in place. Make sure that the quick-release fastener snaps above.

Maintenance and cleaning of the quick-release fastener (TRAX ADVENTURE M / L)

1. Loosen the six screws on the inner side of the case and remove the quick-release fastener.
2. Loosen the screw of the button (fix with thumb and index finger).
3. Loosen the shown clip carefully and …
4. .. remove the quick-release fastener and springs from the mounting plate.
5. Clean the components with clean water and let it air dry. Reattach all parts in reversed order.

Attachement of TRAX ADVENTURE ALU-BOX M & L

1. Lead the four openings of the mounting rails onto the locating bolts of the mounted QUICK-LOCK adapter kit.
   Then press the TRAX ADVENTURE
   ALU-BOX slightly downward until it properly rests on the QUICK-LOCK side carrier.
   ATTENTION: Make sure that all four locating bolts rest on at the same time.
2. Place the latch over the latch hook and…
3. … close the latch; check the proper fit of the TRAX ADVENTURE ALU-BOX on the QUICK-LOCK side carrier.
   ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
   ATTENTION: Secure the TRAX
   ADVENTURE ALU-BOX with the separately available TraX ® EVO / TRAX ADVENTURE lock cylinder set at the QUICK-LOCK side carrier before riding!

Attachement of TRAX ADVENTURE ALU-BOX M & L

1. Lead the four openings of the mounting rails onto the locating bolts of the mounted QUICK-LOCK adapter kit.
   Then press the TRAX ADVENTURE ALU-BOX slightly downward, until it properly rests on the QUICK-LOCK side carrier.
   ATTENTION: Make sure that all four locating bolts rest on at the same time.
2. Place the latch over the latch hook and …
3. … close the latch; check the proper fit of the TRAX ADVENTURE ALU-BOX on the QUICK-LOCK side carrier.
   ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
   ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available TraX ® EVO /
   TRAX ADVENTURE lock cylinder set at the QUICK-LOCK side carrier before riding!

Attachement of TRAX ADVENTURE ALU-BOX M & L

1. Lead the four openings of the mounting rail onto the locating bolts of the mounted QUICK-LOCK adapter plate / STEEL-RACK adapter kit. Then press the TRAX ADVENTURE ALU-BOX slightly forward, until it properly rests on QUICK-LOCK adapter plate / STEEL-RACK adapter kit.
   ATTENTION: Make sure that all four locating bolts rest on at the same time.
2. Place the latch over the latch hook and …
3. … close the latch; check the proper fit of the TRAX ADVENTURE
   ALU-BOX on the QUICK-LOCK
   Adapter Plate STEEL-RACK Adapter Kit.
   ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
   ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available TraX ® EVO / TRAX ADVENTURE lock cylinder set at the QUICK-LOCK adapter plate / STEEL-RACK adapter kit before riding!

TRAX ION

TRAX ADV

Documents / Resources

SW-MOTECH GPT.01.808.70000-B Top Case System [pdf] Instruction Manual GPT.01.808.70000-B Top Case System, GPT.01.808.70000-B, Top Case System, System

References

• User Manual