SVP UDT-02 Wireless Camera Transmitter Instruction Manual

The UDT-02 UHD HEVC Digital Camera Transmitter is a versatile device designed for transmitting high-definition video signals wirelessly. It comes with various accessories including hPAd/PA Ultralinear Power Amplifier, RTC-04 Remote Control, AVF Flexible Antenna, and Cellular Datalink Antenna.

FAQs

Q: What are the main characteristics of the PA Power Amplifiers?
- A: The main characteristics of SVP Broadcast Microwave’s PA Power Amplifiers are explained in Annex A of the manual.
Q: Where can I find information about the different flexible antennas and their characteristics?
- A: Information about flexible antennas is provided in Annex B of the manual.
Q: What standards are described in Annex C?
- A: Annex C describes the DVB-T/T2 standards, their features, and the differences between them.

“`

View Fullscreen

UDT-02 Transmitter Manual V1.1
SW: V1_9809980813-06

Accessories included in this manual:

hPAd / PA Ultralinear
Power Amplifier

RTC-04 Remote Control

AVF Flexible Antenna

Cellular Datalink Antenna

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Annex A: PA Power Amplifiers
This annex explains the main characteristics of SVP Broadcast Microwave’s PA Power Amplifiers.
Annex B: AVF Flexible Antenna User’s Guide
The different flexible antennas and its characteristics are explained in this chapter.
Annex C: Modulation Standards
This chapter describes the DVB-T/T2 standards, as well as their features and the differences between them.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Dear Customer,
We would like to thank you for selecting this equipment and welcome you to the SVP’s growing family of products.
We are sure that the addition of this equipment will give you a complete satisfaction in your existing installation.
Please read these instructions carefully and keep them in hand in case you have to refer to them.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

About this manual
This user’s guide provides indications and explanations about how to set up the UDT-02 easily for the most common use cases. This document is intended to help first time users:
· To find their way around the GUI. · To understand the different possibilities of the UDT-02. · To configure the UDT-02 for their specific configurations. Symbols

The symbols that appear in this manual are:

An information message which indicates explanations for the proper operation of the equipment.

It advises users that if they do not take, avoid or make specific actions, damage could appear in the device.

In the places where this symbol appears it means that by pressing the Down button of the equipment the user can access to the next screen.

This symbol means that pressing the OK button in the options where this symbol appears, the user can access the submenu related to that option or can change the value of the parameter.

<> These symbols mean that the parameter can be modified on the same screen with the right and left keys.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Important Notes
· The UDT-02 HEVC UHD Multiband Transmitter is completely compatible with the DVB-T/T2 Standards, included in the European Standard ETSI EN300744 (DVB-T) and ETSI EN300755 (DVB-T2).
· It is important to note that when the transmitter is switched on, the selected RF output connection must be connected to a suitable antenna or charged.
· It features HEVC, H.264 and Mpeg-2 encoding for 12G, high definition (HD) and standard definition (SD) signals with ultra-low latency. HEVC allows the same video quality, reducing file sizes by up to 50% compared to its predecessor, the H.264.
· The UDT-02 HEVC UHD Multiband Transmitter is available from 1 GHz to 8 GHz, for the DVB-T2 and DVB-T.
· The equipment’s maximum output power for the DVB-T2/T is 100 mW in 2 GHz frequency band, (selectable from -5 to +20 dBm).
· Special care should be taken with SDI cables, quality and length, as these are very important, especially when 12G signals are transmitted.
· If any Audio or data channel are not used in a transmission, they should be disabled, in order to assign that bitrate to the video and achieve a higher quality transmitted video signal.
· Only authorized personnel should open the unit and any repair or warranty will be invalidated if the seals are broken.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Safe Operating Procedures

In this section the safety requirements are shown in order to ensure awareness of potential hazard to the personnel who is operating and maintaining the equipment.

FCC

This chapter has been made taking into account the OET bulletin 65, from August 1997, recommended by the FCC (Federal Communications Commission).

The UDT-02 HEVC Transmitter designed to provide services for broadcasting, will not create RF energy exceeding 1.0 mW/cm2, the FCC limit for exposure. This is known as the Maximum Permissible Exposure (MPE) limit. This transmitter follows this law (with the AVF flexible antenna 3 dBi) as long as the distance between the antenna and the person is at least 4 cm. In the case the PA-5 (5 W Power Amplifier), the minimum distance is 28.2 cm and if PA10 (10 W Power Amplifier) is used, the minimum distance is 39.9 cm. SVP Broadcast Microwave, in accordance with the requirements set forth by the FCC, provides this information as a guide to the user. Next are shown the calculations made to obtain those values:

S = MPE in mW/cm2 (milliwatts per square centimetres)

To follow the law, S maximum must be 1.0 mW/cm2

4 · 2

= 4

EIRP = P · G

()
10 10

Where:

EIRP: Equivalent isotropically radiated power

G (dBi): Antenna gain in dBi

P: Output power of the transmitter (W)

R: Distance from the antenna to the transmitter (cm)

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

1. UDT-02 Transmitter with AVF antenna (3 dBi) G = 3 Pmax = 100 mW EIRP = 200 mW Rmin = 4 cm = 1.57 in
2. UDT-02 Transmitter + PA-5 (5 W) with AVF antenna G = 3 Pmax = 5000 mW EIRP = 10000 mW Rmin = 28.2 cm = 11.1 in
3. UDT-02 Transmitter + PA-10 (10 W) with AVF antenna G = 3 Pmax = 10000 mW EIRP = 20000 mW Rmin = 39.9 cm = 15.7 in

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Declaration of RF Exposure Compliance for Exemption from Routine Evaluation Limits
SAR Evaluation AVF-203 antenna
As shown in the point number 2.5.1 from the RSS-102 Radio Standard Specification, SAR evaluation is not required if the separation distance between the user and the radiating element of the device is more than 20 cm.
The equipment, which consists of the UDT-02 Transmitter with the AVF-203 antenna fixed to it, fulfils this requirement. As shown in the figure below, the distance between the device’s radiating element (situated at the top of the antenna) and the nearest part of the user’s body is further than 20 cm in length. If the length from the radiating element to the bottom of the antenna is 20 cm, then the distance between the nearest part of the user’s body and the radiating element will be higher than 20 cm. As the camera user always uses the camera in the same way and the antenna is fixed to the camera, the distance is always maintained.

Conclusion: This equipment is exempted from SAR evaluation.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

RF Exposure Evaluation
As shown in the point number 2.5.2 from the RSS-102 Radio Standard Specification, RF exposure evaluation is required if the separation distance between the user and the device’s radiating element is lower than 20 cm, except when the device operates as follows:
– Below 1.5 GHz and the maximum e.i.r.p. of the device is equal to or less than 2.5 W.
– At or above 1.5 GHz and the maximum e.i.r.p. is equal to or less than 5 W.
Due to the fact, this equipment is going to operate above 1.5 GHz and the maximum e.i.r.p. is 200 mW (with the AVF-203 antenna), this equipment is exempted from the RF exposure evaluation. When this equipment is operating below 1.5 GHz, it is also exempted from the RF exposure evaluation because the maximum e.i.r.p. (200mW) is lower than 2.5 W.
Conclusion: This equipment is exempted from the RF exposure evaluation.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

First Aid in Case of Electric Shock
DO NOT TOUCH THE VICTIM WITH YOUR BARE HANDS until the circuit is broken. SWITCH OFF. If this is not possible, PROTECT YOURSELF with DRY insulating material and pull the victim clear of the conductor.
If breathing has stopped, indicated by unconsciousness, lack of respiratory movements and a `blue’ look to cheeks, lips, ears and nails, START RESUSCITATION AT ONCE.
EMERGENCY RESUSCITATION THE EXPIRED AIR METHOD
(Approved by the Royal Life Saving Society)
1. If possible, lie the victim on his back with his head slightly higher than his feet. Clear the mouth and throat of any obvious obstruction.
2. Kneel on one side of the victim, level with his head. LIFT THE JAW AND TILT THE HEAD BACK AS FAR AS POSSIBLE (Figs. 1a and 1b)
3. One of the following may happen:
a. Breathing may begin and consciousness returns.
b. Breathing may begin but consciousness NOT returns. Turn the victim on his side and ensure that the airway is kept clear.
c. Breathing may return but be NOISY which means that the airway is not fully clear. Try to clear the airway.
4. IF THERE NO SIGN OF BREATHING:
a. Check that the head is still tilted back.
b. Take a deep breath.
c. Pinch the victim’s nose and blow firmly into his mouth (Fig. 2). As you do, the chest will RISE.
d. Turn your head away and take another breath, watching for the chest to FALL (Fig. 3).
5. Start with four quick breaths and then continue with one breath every five seconds (i.e. 12 times a minute). This should be continued until the victim revives or a doctor certifies death.
6. As consciousness returns the victim will start to breathe on his own, and a `pink’ colour replaces the `blue’ look: this is the time to stop resuscitation. Continue to hold his chin up and so keep the airway clear.
7. In the case of injuries to the mouth, it may be necessary to use mouth-to-nose resuscitation. Seal the victim’s mouth with your cheek and blow firmly into his nose, proceeding as above.

Chapter 3: How to order

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

8. In the case of severe facial injuries, it may be necessary to do a manual method of artificial respiration (Silvester-Brosch or Holger Nielsen). Briefly, these methods apply compression to ribcage with the victim lying on his back (S-B) or face down (H.N.) with associated movement of his arms up and out. The cycle of movement should take about five seconds, i.e. the normal breathing phase.
9. Whatever the method, it is ESSENTIAL to commence resuscitation WITHOUT DELAY and to send for medical assistance immediately.
TREATMENT FOR BURNS
If the victim is also suffering from burns, then, without hindrance to resuscitation, observe the following:
1. DO NOT ATTEMP TO REMOVE CLOTHING ADHERING TO THE BURN.
2. If possible, alleviate the pain from the burnt part by immersing in cold water.
3. If help as available or as soon as resuscitation is no longer required, the wound should be covered with a DRY clean dressing.
4. Oil or grease in any form should not be applied.
5. If severely burnt, get the victim to hospital immediately.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Introduction

Chapter 1: Introduction
The UDT-02 is the multifunction and multiband transmitter developed by SVP Broadcast Microwave. The features of this equipment, achievable only by SVP, make this transmitter the most advanced in the market to date.
Its feature HEVC encodes for 12G video quality signals with ultra-low latency. HEVC transmission is possible using 50% lower bitrate.
This new generation transmitter accepts one 12G signal or four 3G/HD/SDSDI video input signals.
The ASI output enables the user to employ the transmitter as a standalone encoder.
The UDT-02 Transmitter performs DVB-T2 and DVB-T modulations with a frequency band from 1 GHz to 3 GHz and optionally 1 to 8 GHz wide band. DVB-T enables compatibility with nearly all types of receivers. DVB-T2 modulation outperforms DVB-T modulation and offers much higher data rate, which renders a higher signal quality or much more robust signal than other modulations, achieving longer and more complex links.
Control, operation and monitoring of the UDT-02 Transmitter are very friendly. All the parameters of the transmitter can be configured in field. Furthermore, 7 presets are configurable for quick equipment set up. A wide range of accessories allows the use of this equipment in many different applications.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

General Features
This transmitter features HEVC, H.264 and Mpeg-2 encoding for 12G, high definition (HD) and standard definition (SD) signals with ultra-low latency. HEVC allows the same video quality, reducing file sizes by up to 50% compared to its predecessor, the H.264.
Among the improvements of this new transmitter is the ability to transmit one 4K UHD signal with HDR at 10-bit 4:2:2 quality or 4 simultaneous 1080p50/59HD signals.
It optionally includes integrated Bidirectional camera control with Tally.
Encoded signals can be encrypted using BISS-1 or BISS-E scrambling system, and optionally AES 128 and 256. The encrypted signal will only be received by the receivers that have a valid descrambling key.
It has a display and a keyboard which makes the configuration and monitoring of every parameter of the equipment possible.
The equipment is fed with DC power supply from 10 to 36V. It can be powered through DC power supply connector or through the battery mount (optional).
Its excellent design, mechanical and electronic assembly make the UDT-02 a robust and reliable solution.
DVB-T2 features
It is available from 1 GHz to 8 GHz through three different output bands, being 100 mW the maximum output power in the range 1 to 3 GHz and 50mW in the range between 3 and 8 GHz. High quality components have been used to achieve the best output signal quality.
The UDT-02 digital camera transmitter uses COFDM (Coded Orthogonal Frequency Division Multiplexing) modulation system (1K, 2K, 4K) which provides superior signal robustness and a higher link performance. This technology provides operators with efficient means to overcome the challenges of NLOS propagation and mobile channels propagation.
COFDM spread spectrum modulation system distributes the data over a large number of closely-spaced carriers, for example, 1705 carriers in 2K mode. The data is divided into several parallel data streams, one for each carrier, so, each carrier transports a lower data rate and the symbol duration is longer. Each carrier is then modulated with a QPSK, 16QAM, 64QAM or 256QAM scheme. Moreover, the rotated constellation technique is applied in order to improve the link performance.
A COFDM modulated signal, as it uses a low symbol rate modulation scheme (i.e. where the symbols are relatively long compared to the channel time characteristics), suffers less from intersymbol interference (ISI) caused by multipath propagation. As the duration of each symbol is long, it is feasible to insert a guard interval between the COFDM symbols, thus eliminating the intersymbol and co-channel interference. So, if one carrier’s information is lost, only a small part of the whole information would be lost.
Besides, in COFDM, the sub-carrier frequencies are chosen so that the subcarriers are orthogonal to each other, meaning that cross-talk, interference,

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

between the sub-channels is eliminated. The orthogonality allows high spectral efficiency.
On the other hand, COFDM system is invariably used in conjunction with channel coding (forward error correction). The error correction code used in this equipment is Reed-Solomon coding, which is concatenated with LDPC, and there is an additional interleaving between the two layers of coding. Error correcting codes build redundancy into the transmitted data stream. This redundancy allows bits that are in error or even missing to be corrected in the receiver.
The European ETSI EN 300755 standard defines the following LDPC coding rates: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6. There is a compromise between the coding rate (signal robustness) and the transmitted bit rate. If the coding rate is higher the signal transmission is more robust (1/2 is the most robust) but the bit rate that the system is able to transmit is lower.
Used modulation scheme of each COFDM sub-carrier, QPSK, 16QAM, 64QAM and 256 QAM is also connected with signal robustness and transmitted bit rate. QPSK is the most robust and 256QAM is able to transport a higher bit rate.
Besides the system can define 4 guard intervals: 1/4, 1/8, 1/16 and 1/32. The guard interval is used to reduce intersymbol interferences due to the multipath propagation.
In addition, it also provides several bandwidths: 1.7, 5, 6, 7 and 8 MHz in case there are needed for different applications.
To summarize, with all these characteristics, the maximum bit rate achieved is 46 Mbps.
DVB-T features
The RF stage of the UDT-02 Transmitter is the same as the DVB-T2 one. The difference is found in the modulation part as it is commented below.
The UDT-02 digital camera transmitter uses COFDM (Coded Orthogonal Frequency Division Multiplexing) modulation system (2K mode).
The European ETSI EN 300744 standard defines the following convolutional coding rates: 1/2, 2/3, 3/4, 5/6, 7/8.
Used modulation scheme of each COFDM sub-carrier, QPSK, 16QAM and 64QAM, is also connected with signal robustness and transmitted bit rate. QPSK is the most robust and 64QAM is able to transport a higher bit rate.
Besides the system can define 4 guard intervals: 1/4, 1/8, 1/16 and 1/32.
In conclusion, with all these characteristics, the maximum bit rate achieved is 31.67 Mbps.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Technical features

Chapter 2: Technical features

RF Stage DVB-T2 and DVB-T:

Frequency Range:

1 to 3 GHz

3 to 4 GHz (Optional)

4 to 8 GHz (Optional)

Max. Output Power: Modulation: DVB-T2:
DVB-T :

100 mW (1GHz to 3 GHz Selectable from -5 to +20 dBm ) 50mW (3 GHz to 8 GHz)
COFDM 1K, 2K, 4K QPSK, 16QAM, 64QAM, 256QAM Constellation rotation LDPC FEC: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6 IG: 1/8, 1/16, 1/32 Bandwidth: 1.7, 5, 6, 7, 8 MHz Max. bitrate: 46.4 Mbps COFDM 2K QPSK, 16QAM, 64QAM FEC: 1/2, 2/3, 3/4, 5/6, 7/8 IG: 1/8, 1/16, 1/32 Bandwidth: 5, 6, 7, 8 MHz Max. bitrate: 31.67 Mbps

Video: Inputs:
Formats:

1 x 12G-SDI 4 x 3G, HD, SD-SDI (Optional) 2160p23.98/24/25/29.97/30/50/59.94/60 Hz 1080p23.98/24/25/29.97/30/50/59.94/60 Hz 1080i50/59.94/60 Hz 720p-23.98/24/25/29.97/30/50/59.94/60 Hz 576i50 Hz 480i59.94 Hz

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Audio: Quantity: Formats: Analogue Input: Analogue Max. Level: Phantom Power:

16 channels (8 pairs) Embedded or Analogue 2 pair Line / Mic level 24dBu (Balanced) 48V Phantom Power

Test Signals: Video: Audio:

Bars 16 Audio tones

Data Channels: Data channel: Data rate:

User data / GPS data 1,200 to 57,600 bps

ASI: Input and Output: Remux:

ASI Transport Stream ASI Remux (Optional)

Encryption: BISS: AES (Optional): Encoder: Video compression: Latency: Encoder+Decoder
Profile: Output Bitrate: Audio Encoder:

BISS-1 and BISS-E AES-128 and AES-256
HEVC, H.264 and MPEG2 UHD 59p = 66ms UHD 50p = 75ms FHD 59p = 55ms FHD 50p = 70ms FHD 59i = 83ms FHD 50i = 98ms 4:2:2/4:2:0, 8/10-bit 1 Mbps 90 Mbps MPEG-1 Layer1, MPEG-1 Layer2 and AAC-LC

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Control and Monitorization of the device:

Control Interfaces:

Front panel and display

Web Server interface

RTC-04 via cable

Monitoring:

Encoding parameters

Demodulation parameters

Frequency and output level

Alarms and warnings are sent to the receiver via RF

Presets

7 user define presets

Power Supply: DC input:
Consumption:

10 to 36 V
By batteries Anton-Bauer or V (Needs to be specified at the time of order)
35 W

Mechanical: Size: Weight:
Environmental: Temperature range:

196 x 102 x 48,5 mm 1.2 kg (With V-mount battery interface)
-20 to 45 ºC

Bidirectional camera control (Optional):

Frequency range:

403 to 473 MHz

Output Power:

100 mW

Compatibility:

Panasonic and Sony

Tally:

Tally RED, Tally GREEN and On Camera

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

How to order

Chapter 3: How to order

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.0

Chapter 4: Transmitter Operation and Menus
This section provides the user all the necessary information to control, configure and operate the equipment properly.
4.1 Display
To turn the equipment on and off, press ON/OFF button. When a video, Audio or data input has been selected, a character connected to this input is displayed on the main screen. Next, the main screen of the UDT-02_HEVC Transmitter is shown.

Figure 4.1: UDT-02 front panel / Main screen explanation
Once an option has been selected, the main screen appears and these parameters are displayed:
· Frequency (MHz) · Transmission Standard (DVB-T2, DVB-T,…) · Output power (dBm). 3 options available:
Variable power range from -5 to 20 dBm (DVB-T/T2). High power which means that the output power is 20 dBm. Low power which means that the output power is 14 dBm. · Bandwidth (MHz) · Modulation Scheme · FEC (Forward Error Correction) · Guard Interval · Transmitted bitrate (Mbps)

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

· Video Input selection
Possibilities: SDI, DVB-ASI Transport Stream or Generator. Behaviour of the corresponding character: If the character is static then it means presence of that signal. If the character blinks, then it means absence of that signal.
· Audios status indication: If Audio 1 or 2 is not darkened then it is enabled. On the other hand, if Audio 1 or 2 is darkened then it is disabled.
· Data status indication: If this field is not darkened then it means that data is enabled. On the other hand, if this value is darkened it means that data is disabled. However, when this field is static, its meaning is presence of the data whereas if this field is blinking, it means absence of the data.
· KLV Metadata status indication: If this field is not darkened then it means that KLV metadata is enabled. On the other hand, if this value is darkened it means that data is disabled. Moreover, when this field is static, its meaning is presence of the data whereas if this field is blinking, it means absence of the data.
· Input video signal format.
· Encoder Video Profile (4.2.0 or 4.2.2).
· Latency (Standard Delay, Low Delay or Super Low Delay)
Normal Delay
Low Delay
Ultra Low Delay
Next, the linkages between the input and the character on screen is shown:

SDI

Video

ASI

Test-Pattern

Embedded

Audio

Analogue

Test-Tone

RS232

Data

GPS

KLV

Remux

Table 4.1: Linkages between the input and the character displayed

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.2 LEDs
The UDT-02 Transmitter has 5 LEDs on its front panel that show the information detailed below.

ON/OFF RF

Figure 4.2: UDT-02 front panel LED indication

ALARM REMOTE STATUS

The ON/OFF provides the following information: · If the LED is off, the equipment is not being fed. · If the LED flickers in red, the equipment is being fed but it is turned off. · The Led lights up in green when the equipment is turned on.
The RF LED provides the following information: · If the LED is off, the equipment does not transmit RF signal. · The LED lights up in green when the equipment transmits RF signal, RF stage is active.
The ALARM LED provides the following information: · The LED lights up in red when any alarm occurs. · The different alarms that can appear in the transmitter are: Voltage High. Voltage Low. Temperature High. ASI Overflow: This alarm means that the input bitrate is higher than the one that can be modulated due to the configured parameters (constellation, FEC, GI…). · The different warnings that can appear in the transmitter are: No SDI /ASI Input. No GPS. No KLV.
The REMOTE LED provides the following information: · The LED lights up in blue when the user is connected remotely to the device (through the Web Server).
The STATUS LED provides the following information: · The LED lights up when the encoder is working properly.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.3 Front panel
The UDT-02 camera transmitter is configured following the menus structure on the display. The front panel has 8 buttons to enter and exit the equipment’s control menus and submenus and to navigate through them. The function of each button is detailed in the following sections.

Figure 4.3: UDT-02 front panel
4.3.1 ON/OFF Button To switch the equipment on and off, press this button. When the equipment is turned on, it will display the main screen. If the power fails while the equipment is operating, it will restart automatically when the power returns, not being necessary to press the on/off button again.
Figure 4.4: ON/OFF button
4.3.2 OK Button This button is used to:
· Enter to submenus and change parameters. To access to a submenu, OK button must be pressed. Moreover, in the fields where the enter symbol appears, by pressing the OK button the user can change the value of the selected parameter. To save the introduced value, the OK button must be pressed.
· When the main screen, pressing the OK button the user can access to the alarms screen where the different alarms that are taking place are. To return to the main screen, the cross button must be pressed.
Figure 4.5: OK button

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.3.3 Cross Button
This button is used to:
· Enter from the equipment main screen to the setup menu and vice versa.
· Exit equipment’s submenus.
· This button allows the user to access the main screen from the alarms screen.

Figure 4.6: Cross button
4.3.4 Left and Right Button These buttons are used to:
· To move the cursor towards the digit immediately on the left or right and to select a parameter from different options.

Figure 4.7: Left and Right buttons
4.3.5 Up and Down Button · The up and down arrow buttons allow the navigation on the main menu and the rest of submenus. Using these buttons, the user can enter to the submenu or change a parameter. Once selected, the OK button must be pressed. · These buttons are also used to change, for example, the frequency and PID parameter’s values. Pressing up and down arrows the value of those parameters can be changed, increased or decreased respectively.

Figure 4.8: Up and Down buttons

4.3.6 RF Button
By pressing the RF button, RF output is enabled or disabled. The RF LED indicates the status of the RF output. It is important that before pressing this button, the selected RF output must be conveniently loaded and there is no reflected signal.
In case the device is switched off with the RF output enabled then, when it is switched on again it is necessary to push again this button to enable this feature.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

However, if power supply fails when RF output is enabled then, once power supply returns it is not necessary to push this button because RF output will continue being enabled.
Figure 4.9: RF On/Off button

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.4 Menu Scheme
There is one menu in this transmitter that allows the user to change the transmitter’s parameters and configure them.
To enter the menu of this equipment the cross button must be pressed.
In case you want to return to the principal screen from the menu, the cross button must be pressed. Furthermore, in the case of being in the submenus area, returning to the main screens is achieved by pressing the cross button as many times as it is needed.
On the next page, a scheme that specifies the different menu options available are shown.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

MAIN SCREEN Received signal standard, Bitrate, Video codification, Output video signal format, Profile,
Delay, Audio and Data status, Received frequency, Scheme modulation, FEC, Guard Interval, Bandwidth, Number of cuts.

Video

Encoder

Audio

Continued Continued

SDI
Nº Videos Format Latency Profile Depth Mode

ASI
Status Bitrate

Generator

Audio 1

Audio 2

Audio 3

Audio 4

Audio 5

Audio 6

Audio 7

Audio 8

Nº Videos Format Latency Profile Depth Mode

None
Embedded Analogue
1 Generator

None
Embedded Analogue
2 Generator

None Embedded

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Continued

Continued Data

KLV Metadata

None RS232

GPS

Baud Rate Antenna 5V GPS Info GPS Info

UDT-02 UHD HEVC Digital Camera Transmitter MANUAL V1.1

Bitrate Auto
Manual

TS Parameters

Scrambler

Remux

Service name Program Nº Video PID Audio1 PID Audio2 PID Audio3 PID Audio4 PID Audio5 PID Audio6 PID Audio7 PID Audio8 PID
Data PID PMT PID PCR PID

None BISS-1 BISS-E AES-128 AES-256

IP 32

Continued
DVB-T2
Frequency Power
Bandwidth Modulation LDPC FEC Guard Interval
FFT
UDT-02 UHD HEVC Digital Camera Transmitter MANUAL V1.1

RF
DVB-T
Frequency Power
Bandwidth Modulation
FEC Guard Interval

Continued 33

Continued

Unit

RTC SEL

RTC-04 Conf

Alarms

Monitor

Remote

Miscellaneous

View Config

Temperature Voltage
Battery Pack

Local IP
Mask
Gate
Mode
MAC
Admin Pas Restore
Admin Pas User Pas Restore User
Pas

Keyboard Beep Keyboard Lock Distance Units T / T2 Carrier Activation Key
S/N Encoder S/N Encoder FW Activation Licenses Load Profiles Restore Factory

UDT-02 UHD HEVC Digital Camera Transmitter MANUAL V1.1

Firmware Update Firmware Current Firmware
34

4.5 Menu Navigation
This section contains a detailed description of each parameter that can be configured in the UDT-02 HEVC camera transmitter via the menu.
To enter the menu, press the Cross button in the case of being on the principal screen or in any submenu.
To select a parameter or a submenu use Up, Down arrows. Once selected press OK button to access to a submenu or to edit a parameter. To exit a submenu or a parameter press Cross button.

Figure

means that to have access to the right image that button

must be pushed.

<> Symbols

mean that the parameter can be modified on the same

screen with the right and left keys.

Symbol means that pushing the OK button allows entering to the

options of the submenu.

Several types of parameters are available:
· Eligible: When the user can choose between predetermined states.
<> (They have the symbols near them)
· Editable: When the user can enter a value in that option. (The symbol
is displayed on the right of the name). To save the introduced value, the OK button must be pressed.
· Reading: When the value of that parameter is a monitored parameter that can’t be changed.
To change a parameter, for example, the transmitted frequency, press the OK button in the desired option and then with the Up, Down buttons choose the value. Once the parameter is set, press the OK button to save the value.
Next, the different menus and submenus with the options and the different parameters available are explained. Furthermore, in each figure, example parameters are shown.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6 Menu Structure
The main menu is used to access the main parameters of the transmitter which are explained below. The following menu screen can be accessed by pressing the Cross key from the main screen.
Figure 4.10: Main Menu
· Encoder All the parameters related to the video, Audio and data inputs are configured here. Besides, all video, Audio, multiplexing and data encoding parameters are accessed here.
· RF DVB-T2/T transmission parameters are set in this section. · Unit Parameters related to the Web Server and other internal options
of the transmitter are configured here.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1 Encoder Menu

The Encoder menu allows the configuration of the video, Audio and data input and KLV metadata selection. On this menu, the encoder can be configured to output the bitrate set manually or auto. If auto is selected, the bitrate is set by the modulation parameters automatically (bandwidth, modulation, FEC, GI, FTT number).

The PID assignment for each data transmitter is made in the Encoder menu.

The encryption is enabled or disabled here, and the key of the encryption selected is set inside the encryption menu.

In addition, you can send up to 8 different videos (1 SDI input+ 7 ASI input) by using the Remux option, which can be enabled in this menu.

Next, is explained how to configure each parameter.

By using the Up, Down arrow keys, select the Encoder option and press the OK key.

ENCODER

Video: Generator

Audio:

Data: RS232

ENCODER

KLV Metadata: Off

BitRate: Auto

TS Parameters

ENCODER

Scrambler: None

Remux: Disable

IP OUT: Disable

Line nº 1

Function
Video (eligible parameter): In this field, the video input must be chosen with the Right and Left buttons. Once the video input has been selected, press the OK button to configure the parameters related to it. The available options are:
· SDI · ASI · Generator

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Audio 1 (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 1 input can be chosen with the right and left buttons. Once the Audio 1 input has been selected, press the OK button to configure the parameters related to it.

The available options are:

· None

· Embedded

· Analogue 1

· Generator

Audio 2 (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 2 input can be chosen with the right and left buttons. Once the Audio 2 input has been selected, press the OK button to configure the parameters related to it.

The available options are:

· None

· Embedded · Analogue 2

· Generator

Audio 3 (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 1 input
can be chosen with the right and left buttons. Once the Audio 1 input
has been selected, press the OK button to configure the parameters
related to it. 4
The available options are:

· None

· Embedded

· Generator

Audio 4 (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 2 input
can be chosen with the right and left buttons. Once the Audio 2 input
has been selected, press the OK button to configure the parameters
related to it. 5
The available options are:

· None

· Embedded · Generator

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Audio 5 (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 1 input
can be chosen with the right and left buttons. Once the Audio 1 input
has been selected, press the OK button to configure the parameters
related to it. 6
The available options are:

· None

· Embedded

· Generator

Audio 6 (eligible parameter):
In this field, the sort of Audio signal introduced in the Audio 2 input can be chosen with the right and left buttons. Once the Audio 2 input has been selected, press the OK button to configure the parameters related to it. 7 The available options are:

· None

· Embedded

· Generator

Audio 7 (eligible parameter):
In this field, the sort of Audio signal introduced in the Audio 1 input can be chosen with the right and left buttons. Once the Audio 1 input has been selected, press the OK button to configure the parameters related to it. 8 The available options are:

· None · Embedded

· Generator

Audio 8 (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 2 input
can be chosen with the right and left buttons. Once the Audio 2 input
has been selected, press the OK button to configure the parameters
related to it. 9
The available options are:

· None · Embedded

· Generator

Data (eligible parameter):

In this field, the sort of data input can be selected.

The available options are: 10
· None

· RS232

· GPS

KLV Metadata (eligible parameter) (Optional):

In this field, the KLV metadata can be enabled. This feature is

optional.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

BitRate (eligible parameter):

In this field, the encoder output bitrate mode can be selected.

The available options are:

· Auto · Manual Bitrate (editable parameter)

TS Parameters (editable parameters):

This field consists of the configuration of the parameters of the

Transport Stream. In this option, the different program identifiers

are configured.

Scrambler (eligible parameter):

In this field, the encryption system can be chosen with right and left buttons.

The available options are:

· None

· BISS-1

· BISS-E

· AES-128 (Optional) · AES-256 (Optional)

Remux (eligible parameter) (Optional): 15
In this field, remux option can be activated. This feature is optional.

IP Out (eligible parameter) (Optional): 16
In this field, IP Out option can be activated. This feature is optional.

Table 4.2: Encoder Menu

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.1 SDI Video Input

When SDI input is selected, press OK button to access the video configuration menu. The video format is automatically detected. The parameters which are configured in this section are explained below.
SDI

Nº Videos: 1 Video

Frmt: 1080i50

Latency: Normal

SDI

Profile: 4.2.0

Depth: 8 bits

Mode: H.265

Figure 4.11: SDI Input Menu

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Line nº 1

Function Nº Videos: In this field, the number of videos is selected. The available options are:
· 1 Video. Standard mode for single HD/UHD operation. · 4xHD. Flexible video input format and 4x HD operation.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Format:

In this field, the video format is selected.

The available options are:

· 480i59

· 576i50

· 480p59

· 576p50

· 720p50

· 720p59

· 720p60

· 1080i50

· 1080i59

· 1080i60

· 1080p23

· 1080p24

· 1080525

· 1080p29

· 1080p30

· 1080psf23

· 1080psf24

· 1080psf25

· 1080psf29

· 1080psf30

· 1080p50

· 1080p59

· 1080p60

· 2160p23

· 2160p24

· 2160p25

· 2160p29

· 2160p30

· 2160p50S12

· 2160p59S12

· 2160p60S12

· 4KDCIp23

· 4KDCIp24

· 4KDCIp25

· 4KDCIp29

· 4KDCIp30

· 4KDCIp50

· 4KDCIp59

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

· 4KDCIp60

· 2160p50DL6

· 2160p59DL6

· 2160p60DL6

Latency Mode:

In this field, the latency mode is selected.

The available options are:

· Normal. Highest video quality per bitrate with typical end to

end latency of 800-2000ms.

· Low. Compromise between video quality, bitrate and latency with typical end to end latency of 200-1000ms.

· Ultra Low. Requires the most bitrate but with typical end to end latency of a few frames, HEVC mode only.

Profile (eligible parameter):

In this field, the chroma format is selected.

The available options are:

· 4:2:0 Lowest bitrate required.

· 4:2:2 Recommended for interlaced applications, and highest picture quality.

Bit Depth:

In this field, the bit depth is selected.

The available options are:

· 8-bit. Lowest bitrate required.

· 10-bit. Recommended for HDR applications, and highest picture quality.

Encoding Mode:

In this field, the Encoding mode is selected.

The available options are:

· H.265 HEVC. Highest video quality per bitrate, and lowest

latency options.

· H.264 AVC. Greater compatibility with legacy systems, and low

latency option.

· MPEG-2. Not recommended unless specifically required, limited to 8-bit 4:2:0 1080p30

Table 4.3: SDI Input menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.2 ASI Video Input
When ASI input is selected, the signal is directly sent to the modulator. This input is also used for Remux. When Remux option is enabled, the second video which is going to be sent must be connected to the ASI input, but the selected video input must be SDI (according to the inserted video input for the first channel to be remuxed) but not ASI.
ASI IN Status: Present Bitrate: 18.0Mb

Line nº 1 2

Figure 4.12: ASI Input Menu
Function Status (reading parameter): This field indicates if there is any ASI signal in the ASI input. If there is ASI signal, this field will display the word “Present”. If there is no ASI signal then, “No present” will be displayed. The available options are:
· Present · No Present Bitrate (reading parameter): In this option, the bitrate of the ASI input signal is shown.
Table 4.4: ASI Input menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.3 Generator Video Input
In this section the video generator can be configured, this option is used for tests when there is no video source.

Line nº 1

GENERATOR

Nº Videos: 1 Video

Frmt: Auto HD

Latency: Normal

GENERATOR

Profile: 4.2.0

Depth: 8 bits

Mode: H.265

Figure 4.13: ASI Main Screen

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Format:

In this field, the video format is selected.

The available options are:

· 480i59

· 576i50

· 480p59

· 576p50

· 720p50

· 720p59

· 720p60

· 1080i50

· 1080i59

· 1080i60

· 1080p23

· 1080p24

· 1080525

· 1080p29

· 1080p30

· 1080psf23

· 1080psf24

· 1080psf25

· 1080psf29

· 1080psf30

· 1080p50

· 1080p59

· 1080p60

· 2160p23

· 2160p24

· 2160p25

· 2160p29

· 2160p30

· 2160p50S12

· 2160p59S12

· 2160p60S12

· 4KDCIp23

· 4KDCIp24

· 4KDCIp25

· 4KDCIp29

· 4KDCIp30

· 4KDCIp50

· 4KDCIp59

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

· 4KDCIp60

· 2160p50DL6

· 2160p59DL6

· 2160p60DL6

Latency Mode:

In this field, the latency mode is selected.

The available options are:

· Normal. Highest video quality per bitrate with typical end to

end latency of 800-2000ms.

· Low. Compromise between video quality, bitrate and latency with typical end to end latency of 200-1000ms.

· Ultra Low. Requires the most bitrate but with typical end to end latency of a few frames, HEVC mode only.

Profile (eligible parameter):

In this field, the chroma format is selected.

The available options are:

· 4:2:0 Lowest bitrate required.

· 4:2:2 Recommended for interlaced applications, and highest picture quality.

Bit Depth:

In this field, the bit depth is selected.

The available options are:

· 8-bit. Lowest bitrate required.

· 10-bit. Recommended for HDR applications, and highest picture quality.

Encoding Mode:

In this field, the Encoding mode is selected.

The available options are:

· H.265 HEVC. Highest video quality per bitrate, and lowest

latency options.

· H.264 AVC. Greater compatibility with legacy systems, and low

latency option.

· MPEG-2. Not recommended unless specifically required, limited to 8-bit 4:2:0 1080p30

Table 4.5: Generator Input menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.4 Audio Embedded 1 to 8
When Embedded Audio is selected, it means that the transmitted Audio is catch from the video input selected, where the Audio is embedded. There are up to 8 pairs of embedded audio.

ENCODER AUDIO Mode: LPCM-16 Bitrate: 256K

Figure 4.14 : Audio Embedded Input Menu

Line nº 1 2

Function
Audio Stream Encoding Mode: In this field, the audio stream encoding mode 1 to 8 is selected. The available options are:
· LPCM. Ultra Low latency uncompressed audio or data. Bit depth requirements may vary for data, typically 20-bit for Dolby pass-through.
· MPEG-1 L1. Ultra Low latency compressed audio. · MPEG-1 L2. Low Latency compressed audio, Low/Normal
latency modes use a higher quality codec on streams 1-4. · AAC-LC. Highest audio quality per bitrate, using with Ultra Low
latency mode will increase video latency. Only audios 1 to 4.
Audio Stream Bitrate (Kb/s): In this field, the audio stream bitrate, currently information only which depends on the encoding mode.
Table 4.6: Audio Embedded Input menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.5 Audio Analogue 1 or 2

When Analogue Audio is selected, the Audio is catch from the external Audio input. The cable from Lemo 5 to XLR-4 is needed, this cable is provided together with the transmitter. There are 2 pairs of analogue audio.

ENCODER AUDIO

Mode: LPCM-16

Bitrate: 256K

Level:Line

Figure 4.15 : Audio Embedded Input Menu

Line nº 1 2 3

Function
Audio Stream Encoding Mode: In this field, the audio stream encoding mode 1 to 8 is selected. The available options are:
· MP1 L1. Ultra Low latency compressed audio. · MP1 L2. Low Latency compressed audio, Low/Normal latency
modes use a higher quality codec on streams 1-4. · AAC. Highest audio quality per bitrate, using with Ultra Low
latency mode will increase video latency. Audio Stream Bitrate (Kb/s): In this field, the audio stream bitrate, currently information only which depends on the encoding mode. Level: In this field, the type of analogue audio input can be selected. The available options are:
· Line. · Micro Dynamic. · Micro Phantom. · Variable.
Table 4.7: Audio Embedded Input menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.6 Audio Generator 1 to 8 This Audio tone can be used for tests when an Audio source is not available.

ENCODER AUDIO Mode: LPCM-16 Bitrate: 256K

Figure 4.16 : Audio Embedded Input Menu

Line nº 1 2

Function
Audio Stream Encoding Mode: In this field, the audio stream encoding mode 1 to 8 is selected. The available options are:
· MP1 L1. Ultra Low latency compressed audio. · MP1 L2. Low Latency compressed audio, Low/Normal latency
modes use a higher quality codec on streams 1-4. · AAC. Highest audio quality per bitrate, using with Ultra Low
latency mode will increase video latency.
Audio Stream Bitrate (Kb/s): In this field, the audio stream bitrate, currently information only which depends on the encoding mode.
Table 4.8: Audio Embedded Input menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.7 Data
To select the desired sort of data, press Right, Left buttons (eligible parameter). The available options are:
None RS232 GPS
4.6.1.7.1 None
This option is selected when no data is inserted to the transmitter.
4.6.1.7.2 RS232 Screen
DATA INPUT RS232 Baudrate: 9600 <> GPS Info:

Figure 4.29: RS232 Input Menu

Data option 1 2

Parameters Baudrate (eligible parameter): Select the baudrate at which data user is received (Baudrate options are: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200). GPS Info: (eligible parameter): When GPS data is transmitted, GPS position is shown in this menu.
Table 4.9: RS232 Parameters

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.7.3 GPS If this option is selected, you can receive the GPS information from the internal GPS receiver using an external GPS antenna (which must be connected to the GPS Antenna Input). This information is sent to receiver. The antenna is fed directly from the transmitter at 5 V.
Figure 4.17:Internal GPS Main screen

Figure 4.18: GPS Transmitter screen
The GPS info option screen shows the following information:
· Latitude of the Transmitter: The latitude position of the transmitter is specified.
· Speed of the Transmitter: It shows the speed of the transmitter in knots.
· Direction of the Transmitter: The direction of the transmitter is shown in this field.
· Longitude of the Transmitter: The longitude position of the transmitter is specified.
· Height of the Transmitter: The height of the transmitter from ground is specified in this value.
· Satellite Level: The level of each satellite signal received is shown in this field.
· Date: The updated date is shown.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.16 KLV Metadata (Optional)

When this option is ON, the KLV Metadata embedded on the SDI signal is sent through the radio link.
If KLV metadata is not embedded on SDI input, the UDT-02 Transmitter will show an alarm indicating that the KLV is not present.

ENCODER

KLV Metadata: On <

BitRate: Auto

TS Parameters

Figure 4.19: KLV Metadata option

Once that KLV is received at ground, using the TS over IP output of the receiver, KLV metadata can be monitored by a Mission Monitor program.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.17 Bitrate
The encoder output option allows the configuration of the transport stream bitrate. When you use the transmitter’s ASI output, the output bitrate can be set manually on this screen. When the RF is enabled, the modulator starts working and the output bitrate is set by the modulation parameters, changing automatically to Auto mode.
ENCODER KLV Metadata: On < BitRate: Auto TS Parameters
Figure 4.20: Encoder Output Menu

Line nº 1

Function
Bit Rate (eligible parameter): In this field, the output bitrate is shown. When it is wanted to select between an automatic bitrate or configure manually the bitrate, press Right, Left buttons. If manual configuration is selected then, press OK button to select the desired bitrate with the UP, Down keys. Press the OK button to save the introduced value. The available options are:
· Auto · Manual (editable parameter)
Figure 4.21: Encoder Output menu options

If the user selects the manual option, the first and second lines disappear on the main screen.
When the encoder output is in Manual, if you activate the RF, the encoder output changes to AUTO mode automatically.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.18 TS Parameters

ENCODER TS Service Name Program Nº: 2 Video PID: 200
ENCODER TS Audio1 PID: 201 Audio2 PID: 202 Audio3 PID: 203

ENCODER TS Audio4 PID: 204 Audio5 PID: 205 Audio6 PID: 206

ENCODER TS Audio7 PID: 207 Audio8 PID: 208 Data PID: 209

ENCODER TS

PMT PID:

204

PCR PID:

204

KLV Metadata: 212

Figure 4.22: TS Parameters Menu

Line nº 1 2 3

Function
Service Name (editable parameter):
Here the Service name must be entered. To change its value, first press the OK button and then, with the UP, Down arrows select the desired letter. With the Right, Left keys, the user can select the character of the word. Press the OK button to save the introduced value.
Program Nº (editable parameter):
Here the Program number must be entered. To change its value, first press the OK button and then, with the UP, Down arrows select the desired number. Press the OK button to save the introduced value.
Video PID (editable parameter):
Here the Video packet identifier must be entered. To change its value, first press the OK button and then, with the UP, Down arrows select the desired number. Press the OK button to save the introduced value.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Audio 1 PID (editable parameter):

Here the Audio1 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Audio 2 PID (editable parameter):

Here the Audio2 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Audio 3 PID (editable parameter):

Here the Audio1 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Audio 4 PID (editable parameter):

Here the Audio2 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Audio 5 PID (editable parameter):

Here the Audio1 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Audio 6 PID (editable parameter):

Here the Audio2 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Audio 7 PID (editable parameter):

Here the Audio1 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Audio 8 PID (editable parameter):

Here the Audio2 packet identifier must be entered. To change its

value, first press the OK button and then, with the UP, Down arrows

select the desired number. Press the OK button to save the

introduced value.

Data PID (editable parameter):

Here the Data packet identifier must be entered. To change its value,

first press the OK button and then, with the UP, Down arrows select

the desired number. Press the OK button to save the introduced

value.

PMT PID (editable parameter):

Here the Program Map Tables packet identifier must be entered. To

change its value, first press the OK button and then, with the UP,

Down arrows select the desired number. Press the OK button to save

the introduced value.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

PCR PID (editable parameter):

Here the Program Clock Reference packet identifier must be entered.

To change its value, first press the OK button and then, with the UP,

Down arrows select the desired number. Press the OK button to save

the introduced value.

KLV PID (editable parameter):

Here the KLV Metadata packet identifier must be entered. To change

its value, first press the OK button and then, with the UP, Down

arrows select the desired number. Press the OK button to save the

introduced value.

Table 4.10: Encoder TS menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.19 Scrambler In this section the signal can be encrypted with different encryption methods.

ENCODER TS Parameters

Scrambler: None >

Remux: Disable

Figure 4.23: Scrambler menu

Line nº 1

Function Mode (eligible parameter): To choose the desired encryption, press the Right, Left keys. The available options are:
· None · BISS-1 · BISS-E · AES-128 (Optional) · AES-256 (Optional)
Table 4.11: Scrambler menu options

To introduce the key of the encryption, follow these steps: 1. Choose the correct encryption. 2. Press the OK button to introduce the key. 3. With Left and Right buttons select one field and with UP, Down buttons choose one value from 0 to 9 or A to F. 4. Press the OK button to set the key.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.1.20 Remux (Optional)

Remux option allows the transmitter to send up to 8 services multiplexed in one TS. The TS to be multiplexed with the TS from the encoder must be introduced in the ASI input.

ENCODER TS Parameters

Scrambler: None

Remux: Enable

Figure 4.24: Remux menu screen

Please, make sure that the TS parameters are different for all services. When the Remux option is enabled, the Encoder Output is changed to manual bitrate mode. The modulator bitrate must be set to support the total bitrate; Manual bitrate + ASI input bitrate must be lower than the bitrate configured in the modulator.

Figure 4.25: Remux work diagram
ASI bitrate must be known.
You must configure it to have ASI input Bit rate plus NTT encoder Bit rate minor than modulator total Bit rate.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.2 RF Menu

4.6.2.1 DVB-T2
Here we can change different parameters of the T2 modulation. Some of these parameters affect the output bitrate of the modulator and the characteristics of the link: more robustness or more bitrate.

DVB-T2

F: 2.300,00MHz

Power: PA(High)

Bandwidth:8MHz

DVB-T2 Modul: 16 QAM LDPC Fec: 2/3 GI: 1/32
DVB-T2 FFT: 4K PA Unit

<> <>
>
<

Figure 4.26: DVB-T2 Menu

Line nº 1

Function
Frequency (editable parameter):
Select the frequency at which the signal is going to be transmitted. To establish the frequency value first, press the OK button and then, with the Up, Down arrow buttons select the desired value. To save the introduced value, press the OK button.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Power (eligible parameter):

The output power can be selected with the Right and Left buttons.

The available options are:

· Manual (from -5 to 20 dBm) (without precorrection):
To establish the output power value, first press the OK button and then, with the Up, Down buttons select the desired value. To save the introduced value, press the OK button (editable parameter).

· Low (10 dBm) (precorrection until 4Ghz)

· High (20 dBm) (precorrection until 4Ghz)

· PA (Low)

· PA (Mid) · PA (High)

Power is automatically configured to PA mode when there is communication between the UDT-02 and the PA. Then, the output power can be selected using Left and Right buttons. The output power indicated as Low, Mid and High will depend on the PA model used.

Bandwidth (eligible parameter):

Here the bandwidth of the transmitted signal can be chosen. Use Right, Left buttons to select the desired value.

The available options are:

· 1.7 MHz

· 5 MHz

· 6 MHz

· 7 MHz

· 8 MHz

Modulation (eligible parameter):
Here the constellation can be chosen. Use the Right, Left buttons to select the desired constellation.

The available options are:

· QPSK

· 16QAM

· 64QAM

· 256QAM

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

LDPC FEC (eligible parameter):

Here the value of the Forward Error Correction can be chosen. Use the Right, Left buttons to select the desired value.

The available options are:

· 1/2

· 3/5

· 2/3

· 3/4 · 4/5

· 5/6

Guar Interval (eligible parameter):

Here the operation mode can be chosen. Use Right, Left buttons to select the desired value.

The available options are:

· 1/8

· 1/32

· 1/16

FFT Mode (eligible parameter):

Here the number of FFT points can be chosen. Use Right, Left

buttons to select the desired buttons.

The available options are:

· 2K · 4K

PA Unit (reading parameter):

In this field, all the parameters measured in the PA are shown when

there is communication between the transmitter and the power

amplifier.

Table 4.12: DVB-T2 menu option

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.2.2 DVB-T
Here we can change different parameters of the DVB-T modulation. Some of these parameters affect the output bitrate of the modulator and the characteristics of the link: more robustness or more bitrate.

DVB-T

F: 2.300.00MHz

Power: PA(High)

Bandwidth: 8 MHz <

DVB-T

Modul: 16 QAM

Fec: 2/3

GI: 1/16

DVB-T PA Unit

Figure 4.27: DVB-T Menu
With these parameters the modulation parameters in DVB-T are configured. This is how we can vary the robustness and the bitrate of the link.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Line nº 1 2
3 4

Function
Frequency (editable parameter):
Select the frequency at which the signal is going to be transmitted. To establish the frequency value, first press the OK button and then, with the Up, Down arrow buttons select the desired value. To save the introduced value, press the OK button.
Power (eligible parameter):
The output power can be selected with the Right and Left buttons.
The available options are:
· Manual (from -5 to 20 dBm), (without precorrection): To establish the output power value, first press the OK button and then, with the Up, Down buttons select the desired value. To save the introduced value, press the OK button (editable parameter).
· Low (10 dBm), (with precorrection) · High (20 dBm), (with precorrection) · PA (Low) · PA (Mid) · PA (High)
Power is automatically configured to PA mode when there is communication between the UDT-02 and the PA. Then, the output power can be selected using Left and Right buttons. The output power indicated as Low, Mid and High will depend on the PA model used.
Bandwidth (eligible parameter):
Here the bandwidth of the transmitted signal can be chosen. Use Right, Left buttons to select the desired value.
The available options are:
· 5 MHz · 6 MHz · 7 MHz
· 8 MHz
Modulation (eligible parameter):
Here the constellation can be chosen. Use Right, Left buttons to select the desired constellation.
The available options are:
· QPSK · 16QAM · 64QAM

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

5 6 7

FEC (eligible parameter): Here the value of the Forward Error Correction can be chosen. Use Right, Left buttons to select the desired value. The available parameters are:
· 1/2 · 2/3 · 3/4 · 5/6 · 7/8
GI (eligible parameter): Here the Guard Interval value can be chosen. Use Right, Left buttons to select the desired value. The available options are:
· 1/32 · 1/16 · 1/8
PA Unit (reading parameter): · In this field, all the parameters measured in the PA are shown when there is communication between the transmitter and the power amplifier.
Table 4.13: DVB-T menu option

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.2.3 Symbol Rate calculation

To calculate the symbol rate needed for a determined bandwidth, the next

equation must be implemented:

)

Where:

SR: Symbol Rate in Msymb/s

BW: Bandwidth in MHz

Next, a table is shown as an example of the Symbol Rate values for a determined Bandwidth of 28 MHz.

Bandwidth (MHz)

Roll-off

Symbol Rate (Msymb/s)

0.20

23.33

0.25

22.4

0.35

20.74

Table 4.14: Symbol Rate calculation

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.3 Unit Menu
In this section, the Remote Control is configured. By using the Up, Down arrow keys, select the Unit option and press the OK key.
UNIT RTC-04: Disable > RTC-04 Config: Alarms (None) View>
UNIT Monitor Remote Miscellaneous
UNIT Firmware
Figure 4.28: Unit Menu

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.3.1 RTC Selection
In the Profile option, use the Right and Left buttons to select RTC-04 when the Remote Control is going to be connected, or disable it. Once you have selected, press OK button to access to the profiles mode.

UNIT RTC-04: Disable > RTC-04 Config: Alarms (01) View>
Figure 4.29: Unit Profile Menu

· Disable: The UDT-02 Transmitter works without the Profile option.
· RTC-04: Select this option when the NVIS RTC-04 is used.
4.6.3.2 RTC-04 Remote Control Screen

When we enter in the RTC-04 profile, the channel selection screen will appear:

PROFILE

PA Low

M 1 2 3 4 5 6 789

Figure 4.30: Profile Selection
This screen enables the user to choose one channel from the channel group that has been previously configured. If one of the channels is selected, a line under the channel number will appear and the device will be ready to work in that configuration. To access to the channel and see its configuration, the down button must be pressed for a short time. It is also possible to access to the main screen of a channel by pressing up button for a short time. Alarms and warnings are displayed if you press OK button for a short time. The output power configured on the RTC-04 is shown on the main screen of the channel selection.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

PROFILE

PA Low

M 1 2 3 4 5 6 789

Figure 4.31: Profile selected
To return to the Main menu and change the UDT-02 configuration, press MAIN MENU. You will get out of remote control operation.

While the user is controlling the Transmitter via a Remote control, Web Server is not accessible.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.3.3 RTC-04 Config
In this option, a profile can be configured. Select RTC-04 Config option and then by pressing the OK button, the available profiles will be displayed. There are seven profiles available and can be enabled or disabled.

Figure 4.32: Profile Config Menu
Select a profile and then press the OK button to configure the parameters related to it:

PROFILE 1

System:DVB-T2

Freq: 2.300,00MHz

Bandwidth:8MHz

PROFILE 1

Nº videos:1 Video

Format: 480i59

Latency: Normal

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

PROFILE 1

Profile:4.2.0

Depth: 8 bits

Mode:H265

PROFILE 1
Audio1:Embedded <> Audio2:Embedded <> Audio3:Embedded <>

PROFILE 1
Audio4:Embedded <> Audio5:Embedded <> Audio6:Embedded <>

PROFILE 1
Audio7:Embedded <> Audio8:Embedded <> Data Input: None>

PROFILE 1

KLV Metadata:_Off

Scrambler:None

Service Name

PROFILE 1
Program Nº: 1 Video PID: 200 Audio1 PID: 201

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

PROFILE 1 Audio2 PID: 202 Audio3 PID: 203 Audio4 PID: 204
PROFILE 1 Audio5 PID: 205 Audio6 PID: 206 Audio7 PID: 207

PROFILE 1
Audio8 PID: 208 Data PID: 209 PMT PID: 210

PROFILE 1

PCR PID: 211

KLV Metadata: 40

Remux: Disable

Figure 4.33: Profile 1 Menu

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Line nº 1 2 3
4
5

Function
System (eligible parameter): Select the type of the transmission system with the Right and Left buttons. There are two options available:
· DVB-T2 · DVB-T Frequency (editable parameter): Select the frequency at which the signal is going to be transmitted. Press the OK button and with Up, Down keys configure the desired value.
Bandwidth (eligible parameter): Select the desired bandwidth with the Right and Left buttons. There are five options available:
· 1.7 MHz (Only DVB-T2) · 5 MHz · 6 MHz · 7 MHz · 8 MHz Modulation (eligible parameter): In this field, the modulation must be chosen with the Right and Left buttons. The available options are:
· QPSK · 16QAM · 64QAM · 256QAM (Only DVB-T2) LDPC Fec (eligible parameter): Select the desired FEC value with the Right and Left buttons. The available options are: · 1/2 · 3/5 · 2/3 · 3/4 · 4/5 · 5/6 · 7/8

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

FFT (eligible parameter):

Select the desired FFT value with the Right and Left buttons.

The available options are:

· 1K

· 2K

· 4K All options are not available with all modulation parameters.

Guard Interval (eligible parameter):

Select the desired GI value with the Right and Left buttons.

The available options are:

· 1/4

· 1/8

· 1/16

· 1/32

Video Input (eligible parameter):

In this field, the video input must be chosen with the Right and Left buttons.

The available options are:

· SDI

· ASI

· Generator

Number oof Videos (eligible parameter):
In this field, the number of video inputs must be chosen with the Right and Left buttons.

The available options are:

· 1 video

· 4 x HD

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Format:

In this field, the video format is selected.

The available options are:

· 480i59

· 576i50

· 480p59

· 576p50

· 720p50

· 720p59

· 720p60

· 1080i50

· 1080i59

· 1080i60

· 1080p23

· 1080p24

· 1080525

· 1080p29

· 1080p30

· 1080psf23

· 1080psf24

· 1080psf25

· 1080psf29

· 1080psf30

· 1080p50

· 1080p59

· 1080p60

· 2160p23

· 2160p24

· 2160p25

· 2160p29

· 2160p30

· 2160p50S12

· 2160p59S12

· 2160p60S12

· 4KDCIp23

· 4KDCIp24

· 4KDCIp25

· 4KDCIp29

· 4KDCIp30

· 4KDCIp50

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Latency (eligible parameter):

In this field, the delay of the coding process is configured. To select the desired delay, press Right, Left arrows buttons.

The available options are:

· Normal

· Low

· Ultra Low

Video Profile (eligible parameter):

In this field, the codification profile can be configured. To select

the desired profile, press Right, Left arrows buttons.

The available options are:

· 4.2.0

· 4.2.2

Bit Depth:

In this field, the bit depth is selected.

The available options are:

· 8-bit. Lowest bitrate required.

10-bit. Recommended for HDR applications, and highest picture quality.

Encoding Mode:

In this field, the Encoding mode is selected.

The available options are:

· H.265 HEVC. Highest video quality per bitrate, and lowest

latency options.

· H.264 AVC. Greater compatibility with legacy systems, and

low latency option.

· MPEG-2. Not recommended unless specifically required, limited to 8-bit 4:2:0 1080p30

Audio1-2 Input (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 1 or audio 2 input can be chosen with right and left buttons.

The available options are:

· Embedded

· Analogue

· Tone.Gen

· None

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Audio3-8 Input (eligible parameter):

In this field, the sort of Audio signal introduced in the Audio 3-8 input can be chosen with right and left buttons.

The available options are:

· Embedded

· Tone.Gen

· None

Data Input (eligible parameter):

In this field, the data input must be chosen with the Right and Left buttons.

The available options are:

· RS-232

· GPS

· None

KLV Metadata (eligible parameter): 18
In this field, the KLV metadata can be enabled or disabled.

Scrambler (eligible parameter):

Select the desired encryption with the Right and Left buttons.

There are five options available:

· None 19
· Biss-1 · Biss-E

· AES-128 (optional)

· AES-256 (optional)

Service Name (editable parameter): 20
Set the name of the service.

Program Number (editable parameter): 21
Here the program number must be entered.

Video PID (editable parameter): 22
Here the video packet identifier must be entered.

Audio 1-8 PID (editable parameter): 23
Here the Audio 1 packet identifier must be entered.

Data PID (editable parameter): 24
Here the data packet identifier must be entered.

PMT PID (editable parameter): 25
Here the program map tables packet identifier must be entered.

PCR PID (editable parameter):

Here the program clock reference packet identifier must be

entered.

KLV Metadata (editable parameter): 27
Here the KLV Metadata packet identifier must be entered.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Remux: 28
You can enable or disable remux mode with Right and Left buttons.
Table 4.15: Profile menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.3.4 Alarms
In this section, you can View and Configure the Alarms shown by the Transmitter. You can select view or configure the alarms by pressing Left and Right arrows. The alarm screen can be accessed by pressing the OK button from the main screen as well. To return to the main screen from the alarm screen, the Cross button must be pressed. The different alarms and warnings that can be configured in the transmitter are:
· High Voltage · Low Voltage · High Temperature · ASI Overflow: this alarm means that the bit rate at the ASI input is
higher than the one that can be modulated due to the parameters configured (constellation, FEC, GI…). · No SDI Input: SDI source is not connected. · No ASI Input: ASI source is not connected. · No GPS: GPS source is not connected. · No KLV · Encoder Fault · PA No Forward · PA Rev High · PA Volt Low · PA Temp High · WeightOnWheels

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.3.5 Monitor
UNIT MONITOR Mod Temp: +37,1 º C Enc Temp: +57,1 º C Voltage:+11.6V
UNIT MONITOR Battery Pack
Figure 4.34: Unit Monitor Menu
· Temperature (reading parameter): In this field, the internal temperature of the device is displayed. With the Right, Left keys, the user can select if the temperature is shown in ºC or in ºF. Moreover, the value which is between square brackets means the speed of the fans (values from 1 to 4) where 1 means that the fans are stopped and value 4 that they are at the maximum speed. · Voltage (reading parameter): In this field, the voltage of the transmitter is shown. · Battery Pack (reading parameter): In this field, the percentage of the battery is shown.
4.6.3.6 Remote

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Figure 4.35: Unit Remote Menu

Line nº 1
2 3 4 5 6

Function
Local IP (editable parameter):
In this option the IP address of the device can be set in the case that it is wanted to control the device remotely. To change the IP address first press OK button and then, with the Up and Down keys select the desired number. To change from one character to another, press Right and Left keys. Press the OK button to save the introduced value.
Subnet Mask (editable parameter):
Here the Subnet Mask address of the device can be written. To change the Subnet Mask address first press the OK button and then, with the Up and Down keys select the desired number. To change from one character to another, press Right and Left keys. Press the OK button to save the introduced value.
Gateway (editable parameter):
In this option, the address of the Gateway must be written. To change the Gateway address first press OK button and then, with the Up and Down keys select the desired number. To change from one character to another, press Right and Left keys. Press the OK button to save the introduced value.
MAC ADDRESS (reading parameter):
The MAC address of the device is shown.
Admin Pass (editable parameter):
The administrator’s password is introduced. An own password, which is a list of 8 digits, can be set.
To set the password, press the OK button and then use the Up and Down button to establish the desired value. Press Right and Left buttons to change other digits. Finally press the OK button to save the introduced values.
Restore Admin Pass:
This option enables you to restore the default administrator password (00000000).

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

User Pass (editable parameter):

The user’s password is introduced. It can be set an own password

which is a list of 8 digits.

To set the password, press the OK button and then use the Up and

Down button to establish the desired value. Press Right and Left

buttons to change other digits. Finally press the OK button to save

the introduced values.

Restore User Pass:

This option enables you to restore the default user password

(00000000).

Table 4.16: Unit remote menu options

4.6.3.7 Miscellaneous
UNIT MISCELLANEOUS Keyboard Beep: Off < Keyboard Lock: Off < T/T2 Carrier: Off
UNIT MISCELLANEOUS Activ Key:****** S/N: 660010911 Enc S/N: cfe93iif5
UNIT MISCELLANEOUS Enc FW: V3.6.4 Activ Licenses: Load Profiles:
UNIT MISCELLANEOUS Restore Factory:
Figure 4.36: Miscellaneous Menu

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Line Function nº
Keyboard Beep (eligible parameter): If the On option is selected, each time a key is pressed a beep sound will appear. If the Off option is selected, there will be no sound when a key is pressed. 1 The available options are:
· On · Off
Keyboard Lock (eligible parameter): If the On option is selected and the buttons of the equipment remain for 5 minutes without being pressed, a message will appear on the screen saying that the keyboard is locked. By pressing the cross button, the keyboard can be 2 unlocked. If the Off option is selected there will be no messages on the screen. The available options are:
· On · Off
T/T2 Carrier (eligible parameter): The available options are: 3
· On: The carrier (without modulation) is shown for 1 minute. · Off: The option is disabled.
Activation Key (editable parameter): 4 In this field, you can activate your license. You can set the activation key by
pressing the up and down buttons. It must have 8 alphanumeric characters.
S/N (reading parameter): 5
In this field the serial number of the device is shown.
Encoder S/N (reading parameter): 6
In this field the serial number of the Encoder device is shown.
Encoder FW (reading parameter): 7
In this field the FW of the Encoder device is shown.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Activ Licenses:

In this field you can enter the license code for the following optional features:

· AES

· KLV

· Remux

· Internal GPS

· 3-4 GHz band

· 4-8 GHz band

· Cam control

· 4 x HD

· ARINC

· IP

· UHD

Once the code has been introduced, the licence is enabled on the unit. You can use this menu to check which licenses are enabled on this unit. For a new license code, please contact us. Load profiles: 9 In this field you can load profiles from a USB. Restore Factory: 10 In this field you can restore to factory configuration.

Table 4.17: Unit Miscellaneous menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4.6.3.8 Firmware
Update Firmware Current Firmware: V1_1850052859758-04

Line nº 1
2

Transmitter PCB Version Figure 4.37: Firmware Menu
Function Update Firmware: In this field you can update the version of the device. To update the equipment properly, follow the instructions below. Current firmware: In this field, the number of the version installed in the device is shown. The characters which describe the number of the version are inside the red box shown in the figure above. The rest of the characters are important for the manufacturer but are not important for the user.
Table 4.18: Firmware menu options

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Next, the necessary steps to make a successful update are explained. 1. The latest firmware can be found on the website of SVP Broadcast Microwave. To access the firmware file, first enter www.svpbm.com in your web browser. 2. Click on the Support tab.
Figure 4.38 Updating firmware step 2 3. Click on Firmware.

Figure 4.39: Updating firmware step 3

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

4. Go to TX_Firmware.
Figure 4.40: Updating firmware step 4 5. Press the version of the transmitter model (version of the equipment)
to download the file. To verify the version of the transmitter, go to firmware field and then look at the current firmware to check the number installed in the device (the first two digits).

Figure 4.41: Updating firmware step 5

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6. Once the firmware file has been downloaded, save it in a USB device.
In the USB device, the only file that can be allocated inside it is the firmware file of the device to be updated.
7. With the equipment powered off (with no power supply), insert the USB device in the USB connector, placed in the rear panel.
Before introducing the USB device, remove the power supply of the equipment.
8. Now, switch on the device. 9. Go to Unit menu. From the main screen, press cross button to access
the menu. There, with the Up, Down buttons, select the Unit option. 10. Select Firmware by pressing the OK button. 11. Select Update Firmware with the OK button.
Don’t power off the device during the updating process.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

Chapter 5: Web Server
6.1 Introduction
This equipment can be controlled from a PC connected at the rear panel Ethernet connector. To enable the browser interface correctly, the IP address, Subnet Mask, Gateway, User Password and Administrator Password need to be set correctly on this unit. Next, the steps to setup network parameters are shown:
1. Go to Unit -> Remote

Figure 5.1: Web Server screen
2. Select LOC option and set a local IP address. To change the IP address first press the OK button and then, with the Up, Down keys select the desired number. To change from one character to another, press Right, Left keys. Press the OK button to save the introduced value.

Figure 5.2: Local IP

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

3. Select MSK option and set the Subnet Mask address. To change the Subnet Mask address first press OK button and then, with the Up, Down keys select the desired number. To change from one character to another, press Right, Left keys. Press the OK button to save the introduced value.
Figure 5.3: Subnet Mask
4. Select GAT option and set the Gateway address. To change the Gateway address first press the OK button and then, with the Up, Down keys select the desired number. To change from one character to another, press Right, Left keys. Press the OK button to save the introduced value.
Figure 5.4: Gateway
5. Select Admin Pass option and set the administrator’s password. To access to the Webserver directly without setting any password, the Admin Pass must be set to 0 (00000000). However, if you want to set an administrator’s password, it is necessary to introduce 8 digits. In this way, with this password, the administrator can access to the Webserver and make any configuration, modification or monitoring.
Figure 5.5: Admin Pass

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6. Select Restore Admin Pass option to restore the default value of the administrator’s password (00000000).
Figure 5.6: Restore Admin Pass 7. Select User Pass option and set the user’s password. If you want to
access the Webserver directly without setting any password, the User Pass must be set to 0 (00000000). However, if you want to set a user’s password, it is necessary to introduce 8 digits. In this way, with this password, the user can access to the Webserver and make any monitoring, but without changing anything.
Figure 5.7: User Pass 8. Select Restore User Pass option to restore the default value of the
administrator’s password (00000000).
Figure 5.8: Restore User Pass Once the IP, Subnet Mask, Gateway, Admin Pass and User Pass are set and the laptop or PC is connected to the UDT-02 HEVC, open the web browser and type in the Local IP configured in the transmitter. Press the enter button in your computer and then the main screen will appear.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6.2 Web Page Overview
The main menu is set in the upper position of the screen. Once an option is chosen, it is possible to change any parameter allowed, or to see the values of some options. To modify an editable parameter, introduce the new one and press enter button. Then the change will be set in the transmitter device. Moreover, to modify an eligible parameter, select the new one and the change will appear in the transmitter. Next several screens of the web server and their features are shown.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6.2.1 ENCODER

Figure 5.9: Web Server Encoder screen

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6.2.1.16 Video

· Input (eligible parameter):

Select the type of the video input. The video input options available are SDI, ASI and Generator.

· Format (reading parameter):

Here the format of the video input signal is displayed. If there is no video input then the message `not detected’ is displayed.

· Bitrate (reading parameter):

In this field, the user can see the bitrate in Mbps assigned by the encoder to the video input signal.

However, if the introduced signal is ASI, this field indicates the input bitrate of this ASI signal.

· Delay (eligible parameter):

In this field, the delay of the coding process is configured. The available options are Standard Delay, Super Low Delay or Ultra Low Delay.

· Profile (eligible parameter):

In this field, the codification profile can be configured. The available options are 4:2:0 and 4:2:2.

· GOP (eligible parameter):

In this field, the Group Of Pictures parameter is displayed. It specifies the order in which intra and inter-frames are arranged.

The available options are:

Auto

Manual

· Level (eligible parameter):

In this field, the level of the HEVC encoder can be configured. The available options are:

4.0

4.1

4.2 (only available in 1080p-50/59.94/60 Hz video formats)

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6.2.1.17 Audio
· [A1] Input (eligible parameter): Select the type of signal introduced in the Audio 1 input. The Audio input options available are Embedded, Analogue, AES-EBU, Test Tone and None.
· [A1] Bitrate (eligible parameter): Select the bitrate for the coding process of the Audio 1 signal. The available options are 128, 192, 256 and 384 Kbps.
· [A2] Input (eligible parameter): Select the type of signal introduced in the Audio 2 input. The Audio input options available are Embedded, Analogue, AES-EBU, Test Tone and None.
· [A1] L Type (Analogic) (eligible parameters): This field is only configurable if analogic audio signals are introduced. The user can select the sort of signal of the Audio 1 left channel introduced in the transmitter. The available options are: Line MIC Dynamic MIC Phantom
· [A1] R Type (Analogic) (eligible parameters): This field is only configurable if analogic audio signals are introduced. The user can select the sort of signal of the Audio 1 right channel introduced in the transmitter. The available options are: Line MIC Dynamic MIC Phantom

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6.2.1.18 Data
· Input (eligible parameter): Select the type of data introduced to the device. The available options are None, RS232 and 4k board.
6.2.1.18.1 RS-232
If the RS-232 connection is selected, the next parameters must be configured to achieve a successful communication:
· Baudrate (eligible parameter): Choose the baudrate of the RS-232 connection. The available options are 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, 115200, 230400.
· Parity (eligible parameter): Select the parity for the RS-232 connection. The available options are None, Odd and Even.
· Stop Bits (eligible parameter): Establish the number of stop bits for the RS-232 connection. The available options are 1 and 2.
6.2.1.19 GPS (Optional)
If GPS is enabled, then different parameters are shown:

Figure 5.10 Web Server GPS screen
If GPS is enabled and the GPS antenna is connected, the status field will show “GPS data verified” message. Nevertheless, if the transmitter does not detect any GPS input signal, the status field will show “GPS not detected”. The format of the GPS coordinates used is decimal minutes as shown in the next example:

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

N43º02.032′
W023º03.023′
· Status (reading parameter): The status of the GPS input is displayed in this field.
· Latitude (reading parameter): It specifies the latitude position of the transmitter.
· Longitude (reading parameter): It specifies the longitude position of the transmitter.
· Altitude (reading parameter): The height of the transmitter from ground in meters is specified in this value.
· Direction (reading parameter): The direction in degrees of the transmitter is shown in this field.
· Speed (reading parameter): The speed of the transmitter in km/h is shown in this field.
6.2.1.20 KLV Metadata (Optional)
When this option is ON, the KLV Metadata embedded on the SDI signal is sent through the radio link.
6.2.1.21 Encoder output
· TS Bitrate Auto (eligible parameter): The bitrate mode can be automatic or manual. In case automatic mode is selected, the device configures automatically the video bitrate depending on the modulation, FEC, IG, BW used, in order to the video bitrate can be always the maximum allowed. SVP advises the use of the automatic mode when the signal is transmitted through RF. Manual mode is useful when the device is used as an encoder to configure the desired output bitrate in the ASI output.
· TS Bitrate Manual (editable parameter): If the bitrate mode is manual, select the bitrate.

6.2.1.22 TS Parameters

· Video PID (editable parameter): Here the video packet identifier must be entered.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

· Audio 1 PID (editable parameter): Here the Audio 1 packet identifier must be entered.
· Audio 2 PID (editable parameter): Here the Audio 2 packet identifier must be entered.
· Data PID (editable parameter): Here the data packet identifier must be entered.
· PMT PID (editable parameter): Here the program map table packet identifier must be entered.
· PCR PID (editable parameter): Here the program clock reference packet identifier must be entered.
· GPS PID (editable parameter): Here the GPS packet identifier must be entered.
· ALARM PID (editable parameter): Here the Transmitter Alarms identifier must be entered.
· KLV Metadata (editable parameter): Here the KLV packet identifier must be entered.
· Program Number (editable parameter): Here the program number must be entered.
· TS id (editable parameter): In this field the Transport Stream identifier must be set.
· Network id (editable parameter): In this option the network identifier must be specified.
· Network Name (editable parameter): Specify the name of the network.
· Service Name (editable parameter): Set the name of the service.
When editable parameters are being set in the Web Server and new values are being introduced, the text remains in RED until the enter button is pressed. When the enter button is pressed, the new values are saved, and the text will appear in BLACK. It is necessary to press the enter button to save the new values in the transmitter.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

6.2.1.23 Scrambler
If you want an encryption system, it can be chosen here. · None: None encryption · BISS-1: Uses an unencrypted key for the BISS key · BISS-E: Uses an encrypted key · AES 128 (optional) · AES 256 (optional)
6.2.1.24 Remux (Optional)
· Mode (eligible parameter): Here you can enable or disable the Remux mode. When the enable mode is selected, Transport Stream Bitrate mode is always manual so that the user can configure the output bitrate of the TS from the internal NTT encoder. You must configure it considering that the ASI input Bit rate plus the NTT encoder Bit rate must be minor than modulator total Bit rate.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

100

6.2.2 RF

Figure 5.10 Web Server RF screen (DVB-T)
· System (eligible parameter): In this field the transmission standard can be chosen. The available options are DVB-T2 and DVB-T.
· RF Status (eligible parameter): Select ON to activate the RF transmission or press OFF button to deactivate it.
6.2.2.16 DVB-T · Frequency (editable parameter): Introduce the frequency at which the signal is being transmitted. · Power (eligible parameter): Specify the power at which the signal is being transmitted (Variable, Low, High and PA). · Bandwidth (eligible parameter): Enter the transmitted signal bandwidth. The available options are 5, 6, 7 and 8 MHz.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

101

· Modulation (eligible parameter): Select the constellation of the transmitted signal. The available options are QPSK, 16QAM, 64QAM.
· FEC (eligible parameter): Select the FEC value for the transmitted signal. The available options are 1/2, 2/3, 3/4, 5/6, 7/8.
· GI (eligible parameter): Select the guard interval of the transmitted signal. The available options are 1/4, 1/8, 1/16, 1/32.
· Spectrum (eligible parameter): Here the spectrum type is configured. Inverted spectrum is just another method to help prevent signal theft. The available options are normal or invert.
· Bitrate (reading parameter): In this field it is displayed the bitrate of the transmitted signal according to the modulation parameters used.
When editable parameters are being set in the Web Server and new values are being introduced, the text remains in RED until the enter button is pressed. When the enter button is pressed, the new values are saved, and the text will appear in BLACK. It is necessary to press the enter button to save the new values in the transmitter.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

102

6.2.2.17 DVB-T2

Figure 5.11: Web server RF screen (DVB-T2)
· Frequency (editable parameter): Introduce the frequency at which the signal is being transmitted.
· Power (eligible parameter): Specify the power at which the signal is being transmitted (Variable, Low, High and PA).
· Mode (eligible parameter): Select the guard interval of the transmitted signal. The available options are 1/8, 1/16 and 1/32.
· Bandwidth (eligible parameter): Enter the transmitted signal bandwidth. The available options are 1.7, 5, 6, 7 and 8 MHz.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

103

· Modulation (eligible parameter):
Select the constellation of the transmitted signal. The available options are QPSK, 16 QAM, 64 QAM and 256 QAM.
· LDPC FEC (eligible parameter):
Select the FEC value for the transmitted signal. The available options are 1/2, 3/5, 2/3, 3/4, 4/5 and 5/6.
· FFT (eligible parameter):
Specify the FFT mode. The available options are 1K, 2K and 4K.
· Pilot Pattern (reading parameter):
This field indicates the scattered pilot pattern used for the OFDM data symbols. The available options are between PP1 and PP8.
· Time Interleaving (editable parameter):
This option indicates the number of Time Interleaving Blocks (TI blocks) per interleaving frame.
The user must select, in how many TI blocks an interleaving frame is split.
Only the time interleaving mode 0 (TIME_IL_TYPE=0) is supported, so one interleaving frame always equates to exactly one OFDM frame. To deactivate the time interleaving, this parameter must be set to 0.
Press the OK button and then select the Up and Down buttons to configure the desired value.
· TS Bitrate (reading parameter):
In this field it is displayed the bitrate of the transmitted signal according to the modulation parameters used.
When editable parameters are being set in the Web Server and new values are being introduced, the text remains in RED until the enter button is pressed. When the enter button is pressed, the new values are saved, and the text will appear in BLACK. It is necessary to press the enter button to save the new values in the transmitter.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

104

6.2.3 UNIT

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

105

Figure 5.12: Web Server UNIT screen

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

106

6.2.3.16 LEDs Status (reading parameters) · ON/OFF: If the Led is off the equipment is not being fed. The Led lights up in green when the equipment is turned on. If the Led is orange, the equipment is in standby mode. · RF: If the Led is off the equipment does not transmit RF signal. The Led lights up in green when the equipment transmits RF signal, that is, RF stage is active. · ALARM: The Led lights up in red when any alarm occurs. · STATUS: The Led lights up when a change in the configuration of the device is being processed.

6.2.3.17 Alarms (reading parameter) In this option, different alarms which are present in the device are shown.

6.2.3.18 Alarms Configuration (eligible parameter) In this option, the alarms to be shown can be selected. The different alarms that can be configured to be shown are:
· High Voltage · Low Voltage · High Temperature · ASI Overflow: this alarm means that the bit rate at the ASI input is
higher than the one that can be modulated due to the parameters configured (constellation, FEC, GI…). · No SDI Input: SDI source is not connected. · No ASI Input: ASI source is not connected. · No Audio 1 Input: Audio source is not connected. · No Audio 2 Input: Audio source is not connected. · No GPS: GPS source is not connected. · No RS232: RS232 data source is not connected. · No KLV · PA No Forward · PA Rev High · PA Volt Low · PA Temp High

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

107

· WeightOnWheels · TS Error
6.2.3.19 Monitor · Voltage (reading parameter): In this field, the power supply voltage of the transmitter is shown. · Temperature (reading parameter): In this field, the internal temperature of the device is displayed.
6.2.3.20 Configuration · Webserver Address (editable parameter) In this option the IP address of the device can be set if you want to control the device remotely. To change the IP address, introduce the desired number and then press enter to save the introduced value. · Webserver Subnet (editable parameter) Here the Subnet Mask address of the device can be written. To change the Subnet Mask address, introduce the desired value and then press enter to save it. · Webserver Gateway (editable parameter) In this option, the address of the Gateway must be written. To change the Gateway address, introduce the desired value and then press enter to save it. · Webserver MAC (reading parameter) In this field, the MAC address of the device is shown. · Standby Mode (eligible parameter) In this option the user can turn off or on the device by pressing On or Standby options. · Admin Password (editable parameter): In this field, the administrator’s password is introduced. It can be set to an own password which is a list of 8 digits. Then, to save the introduced value, press Enter button. There is the option to restore the default administrator password (00000000). · User Password (editable parameter): In this field, the user’s password is introduced. It can be set an own password which is a list of 8 digits. Then, to save the introduced value, press Enter button. There is the option to restore the default user password (00000000).

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

108

6.2.3.21 Miscellaneous

· Night Mode (eligible parameter):
There are four possible states for the night mode. If the night mode is in state 0 then the light on the screen will be brighter than if it is in state 1. If the state is 3 then, the light on the screen will be the dimmest of the four possible states.
· S/N (reading parameter):
In this field, the serial number of the device is displayed.
· Firmware (reading parameter):
In this field, the number of the version installed in the device is displayed.
When editable parameters are being set in the Web Server and new values are being introduced, the text remains in RED until the enter button is pressed. When the enter button is pressed, the new values are saved, and the text will appear in BLACK. It is necessary to press the enter button to save the new values in the transmitter.
6.2.3.22 Firmware Update

In this field, the user can upload the firmware .SVP file and upgrade the firmware remotely.

6.3 Web Page Setup Notes

For the data to be refreshed correctly, you may need to change some settings on your browser.
Please follow these instructions carefully.

For Google Chrome:

1. Click on the Chrome menu browser.

situated in the toolbar of the

2. Select tools.

3. Choose the option Delete navigation data.

4. Choose the option empty cache.

5. Click on Delete navigation data.

For Internet Explorer: 1. From the Tools menu, select Internet Options.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

109

2. In the General tab, click on the Settings button in the Browsing History section.
3. Select ‘Every time I visit the webpage’ then click the OK button. 4. Click the OK button.
For Mozilla Firefox: 1. Open a new tab, in the address bar enter about:config. 2. In the Filter box, enter disk. 3. Set the value for ‘browser.cache.disk.enable’ to false (double click to change the setting). 4. Close the about:config tab.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

110

Chapter 6: Equipment Installation

6.1 Introduction

This chapter provides important information for the transmitter system installation such as connections available in the rear and front panel of the UDT-02 Transmitter and their pinout, needed connectors and the accessories which are available with the transmitter device.

6.2 Connections

Every connection of the UDT-02 camera transmitter is on the rear panel, except for the RF antenna connections that are on the front panel.
All the Lemo part numbers and pinout refer to the connector of the UDT-02. The pinout is shown as it is seen in the UDT-02.

In all the Lemo connectors, the pin number one is circled and the succeeding pins are in counter clockwise order.
All input and output connections of the transmitter are shown in the figure below:

SDI1 12G SDI2 SDI3 SDI4
ASI In Audio 1 (L&R) Audio 2 (L&R)
RTC GPS PA Remote
Ethernet USB
Power DC

UDT-02 HEVC
Figure 6.1: UDT-02 connections

RF Output (1 3 GHz) RF Output (3 – 4 GHz) RF Output (4 8 GHz) GPS Antenna ASI Out Remote

The following figures show the UDT-02 front and rear panel. Connections mentioned in the upper figure are shown below.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

111

Ground

AUDIO 1 Input

GPS/CVBS 4K Input

BUC-PA-CC

Remote

AUDIO 2 Input

RTC-04

Power DC

DVB-T/T2 DVB-T/T2 3-4 GHz RF 4-6.4 GHz
Output RF Output

DVB-T/T2 1-2.8 GHz RF Output

HDMI 1-2 Input

ASI Input

USB

SDI Input

ASI Output

GPS RF output

Figure 8.2: Rear and front view of the UDT-02

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

112

6.2.1 Power supply

The equipment is powered by a DC source from 8 to 36 V. If the input voltage of the equipment is out of that range, the LED of the equipment blinks GREEN and RED showing an alarm.

The power source of the UDT-02 should be the same as the one used for the PA. Both should be turned on and off simultaneously. They must use the same breaker.

The DC power supply is connected to the equipment via a 4 pin Lemo 1B connector.

Power supply connection technical features

Item

Features

Connector label

8-36V D.C.

Connector type

4 pin Lemo 1B

Part number (UDT-02)

ECG.1B.304

Part number (cable connector)

FGG.1B.304.CLAD52

Input voltage range

8-36 V.

Consumption

20 Watt.

Table 6.1: Power supply connection technical features

Pinout

Figure 6.2: Connector pinout

Description

GND

+ VCC

Table 6.2: Power supply connector pinout

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

113

6.2.2 PA CAMERA Connector

The UDT-02 Transmitter incorporates an input to control remotely the PA-10 Power Amplifier.

PA CAMERA Connector technical features

Item

Features

Connector Label

PA CAMERA

Connector type

7 pin Lemo 0B

Part number (UDT-02)

ECG.0B.307.CLV

Part number (cable connector)

FGG.0B.307.CLAZ

Table 6.3: PA CAMERA Connector features

Pinout of the connector

Description

GND

TX (-)

TX (+)

Weight on Wheels (WoW)

PA ON/OFF

RX (+)

RX (-)

Table 6.4 PA CAMERA connector pinout

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

114

6.2.2.1 PA Remote Control Cable pinout
If the transmitter is configured to be used with PA Power Amplifiers, the communication and control is made through a RS232 port. The pinout of the cable which interconnects the UDT-02 Transmitter and PA Power Amplifier is indicated in the following table:

UDT-02 to PA Control Cable pinout

BUC-PA-CC Cable Connector (Lemo FGG.0B.307)

PA Remote Cable Connector (JD38999/26WA35SN Amphenol)

Pin 1

Pin 2

Pin 6

Pin 5

Pin 7

Pin 2

Table 6.5: UDT-02 to PA Control Cable pinout

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

115

6.2.3 RTC-DATA

This connection is mainly used to allow to transfer RS232 user data or to connect to the RTC remote control.

RTC-DATA connection technical features

Item

Features

Connector Label

RTC-DATA

Connector type

6 pin Lemo 0B

Part number (UDT-02 connector) Part number (Cable connector)

ECG.0B.306.CLV FGG.0B.306.CLAZ

Table 6.6: RTC-DATA connection technical features

Pinout of the cable connector (Watched from the soldering side)

Description

GND

RTC – (RS-485 (-))

DATA TX (RS-232)

RTC + (RS-485(+))

+V DC

DATA RX (RS-232)

Table 6.7: RTC-DATA cable connector pinout

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

116

6.2.4 Video inputs

For transmission of 12G signals, video SDI 1 connector must be used.

SDI 2, SDI 3 and SDI 4 are used for multivideo HD formats.

SDI connection technical features

Item

Features

Connector Label

SDI 1 12 Gb/ SDI 2/ SDI 3/ SDI 4

Connector type

Female HD-BNC

Impedance

Input Level

800 mVpp nominal ±10%

Standards

SMPTE-259M and SMPTE-272M SMPTE-292M and SMPTE-299M SMPTE-425M

Table 6.8: SDI input signal connection features

ASI IN connection technical features

Item

Features

Connector label

ASI IN

Connector type

HD-BNC

Impedance Standard

75 EN50083-9

Maximum Bitrate

216 Mbps

Table 6.9: ASI Transport Stream input connection features

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

117

6.2.5 Audio inputs
The UDT-02 Transmitter has four possible Analogue Audio inputs:
· 2 Audio inputs to insert 2 stereo or 4 mono analogue (mic phantom, mic dynamic and line) signals where connections are made using two 5 pin Lemo 0B connectors on equipment’s rear panel.
· 1 input to insert either 8 Audios embedded on a SDI signal where connections are made with a BNC connector on equipment’s rear panel.
Embedded Audio signals must be compliant with SMPTE-272M standard when embedded on SD-SDI video signal, with SMPTE-299M standard when embedded on HD-SDI video signal and with SMPTE-425M standard when embedded on 3G-SDI video signal.

Analogue Audio input technical features

Item

Features

Audio channel number

Connector labels

AUDIO 1 AUDIO 2

Connector type

5 pin Lemo 0B

Part number (UDT-02 connector)

ECG.0B.305.CLV

Part number (Cable connector)

FGG.0B.305.CLAZ

Table 6.10: Analogue Audio input connection technical features

Pinout of the cable connector (Watched from the soldering side)

Description

A1L+

A1L-

GND

A1R+

A1R-

Table 6.11: Analogue Audio cable connector pinout

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

118

6.2.6 Remote

This connection allows the user to monitor and setup any parameter of the transmitter through Web Browser. The connector used is a RJ-45.

Remote connection technical features

Item

Features

Connector Label

REMOTE

Connector type

RJ-45

Table 6.12: Ethernet remote connection technical features

6.2.7 UPGRADE (USB)

Through the USB connection, it is possible to update the firmware of the transmitter directly from an external USB device.

USB connection technical features

Item

Features

Connector Label

USB

Connector type

Type A

Table 6.13: USB input connection technical features

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

119

6.2.8 RF output

The antenna or Power Amplifier is directly connected to the female N-type or SMA-type connectors on the front panel of the UDT-02 camera transmitter. There are up to six connectors available, each one for a different frequency band (type N for the 1-2.8 GHz band, type SMA for 3-4 GHz band, type N for 4-8 GHz band and SMA connector for GPS antenna)

RF connection technical features

Item

Features

Connector label

1-3 GHz

Connector type

N female

Output frequency range

1 to 3 GHz

Impedance

Output power

Maximum: 100 mW

Item Connector label Connector type Output frequency range Impedance Output power

Features 3-4 GHz SMA female 3 to 4 GHz 50 Maximum: 100 mW

Item Connector label Connector type Output frequency range Impedance Output power

Features 4-8 GHz N female 4 to 8 GHz 50 Maximum: 100 mW

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

120

Item Connector label Connector type Impedance

Features GPS Antenna SMA female 50

Item Connector label Connector type Impedance

Features REMOTE SMA female 50

Table 6.14: RF output connections characteristics

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

121

6.2.9 ASI output

ASI output signal type uses 75 BNC connector. This connector is placed on transmitter’s rear panel.
It is important that 75 connectors are used. This is because the female output connector of the UDT-02 unit could be damaged because of an impedance mismatch.

ASI connection technical features

Item

Features

Connector label

ASI-OUT

Connector type

Mini BNC female

Impedance

Standard

EN50083-9

Maximum Bitrate

100 Mbit/s

Table 6.15: DVB-ASI Transport Stream output connection features

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

122

6.3 Integrated wireless camera control installation diagram

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

123

6.4 Mechanical Accessories
In this section, different short of accessories of the UDT-02 HEVC Transmitter are shown. The accessories required by the customer must be defined when the transmitter is ordered.
6.4.1 Battery Fastening
This item allows the connection to the battery (V type or Anton Bauer) to the transmitter’s case (optional). The type of the battery fastening must be defined when the transmitter is ordered.
Figure 6.3: V type battery fastening

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

124

6.5 5G Antenna 6.5.1 CELLULAR DATALINK Antenna SIM Cover

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

125

6.5.2 CELLULAR DATALINK Antenna : AIRFILM CAMERA SYSTEMS DT-1-1 Assembly

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

126

Remote Control

Chapter 7: Remote Control
7.1 Introduction
The RTC-04 equipment is compact lightweight Remote Controller for SVP Broadcast Microwave transmitters. They can control the UDT-04 and the UDT02 Transmitters. Thanks to this equipment, the user can control the transmitter remotely in an easy and comfortable way. The RTC-04 front panel consists of several switch which allow the user to configure and modify different features such as the actuator arm state (up/down), the level of the RF, the profile selected and enable or disable encryption. From the RTC-04 the user can record video on an USB drive or can charge profiles automatically on an USB port. This equipment is especially useful in applications where the UDT-02 or UDT04 Transmitter is mounted away from the operator and the parameters can’t be modified directly from the front panel. Additionally, when used with a 5G Antenna, we can select between 5G DATA transmission (5G antenna is only used for DATA) or 5G VIDEO (5G antenna is used for video transmission backup).
7.2 RTC-04
7.2.1 Remote Control Operation
This chapter provides the user with all the necessary information to control and operate the equipment properly.

Figure 7.1: RTC-04 front view

There are several buttons in the front panel of the device that allows the control of the UDT-02 and UDT-04 Transmitter remotely.
· Actuator
This Up/Down switch is used to control the antenna actuator in different systems. With this switch, it is possible to move the antenna up and

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

127

down remotely. It has also two LEDs to indicate the status of the actuator (Up or Down). In order to disable the actuator function, please you hold down the PROFILE button and press the Actuator DOWN button for 3 seconds.
· Standby/RF To select the amplifier output power level or leave it in standby mode please move this selector. The options available are: – Standby “.” – RF Off “o” – Low power “L” – Medium power “M” – High power “H”
· Profiles With this button, the user can choose between different profiles which have been configured previously. There are seven profiles available. Each profile has different features related to the type of transmission system, the frequency at which the signal is going to be transmitted, the bitrate, the type of video input, the type of Audio 1 and Audio 2 inputs, the video delay and the codification profile.
· LEDS There are 4 LEDS that can be used for different purposes; Crypto, REC, 5G and 5G Video. In order to access the configuration mode, first press PROFILE button for about 2 seconds. One of the LEDs will start blinking, move UP or Down using PROFILE button and select the option that you want to configure. Press PROFILE button to change the configuration. Press PROFILE button for 2s to get out of configuration mode. Configuration options are: Encyption: – ON – OFF REC (Video recording on USB drive): – ON – OFF

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

128

5G: – ON (Only data is transmitter over bidirectional 5G antenna) – OFF
5G video: – ON (Video is sent over the 5G antenna as video backup) – OFF
7.2.2 Connections
This chapter provides important information such as connections available in the Remote Control and the connectors needed.

Figure 7.2: RTC-04 rear view

7.2.2.1 Transmitter Dimmer Connector

This connector is used for the communication between (J1) UDT-02 Transmitter and the RTC-04 Remote Control.

Transmitter Dimmer connection technical features

Item

Features

Connector label

TRANSMITTER DIMMER J1

Connector type

MIL-DTL-38999 Series 3 D38999/24

Part number E.g. (RTC-04 connector)

D38999/24WA35PN

Part number E.g. (cable connector)

D38999/26WA35SN

Table 7.1: Transmitter Dimmer connection technical features

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

129

Transmitter Dimmer connector pinout

Description

GND

RTC RS485 (+) Half Duplex

RTC RS485 (-) Half Duplex

+V Power Supply

NVG Dimmer

Dimmer Enable

Not Used

USB+ REC

USB- REC

Table 7.2: Transmitter Dimmer connector pinout

7.2.2.2 Actuator Arm Altimeter Connector

This connector is used for the communication between (J2) HDT-04 Transmitter and the actuator arm. This connector has different pinouts depending on the internal selection of the actuator type; type A or Type B as described below.

Actuator Arm Altimeter connection technical features

Item

Features

Connector label

ACTUATOR ARM ALTIMETER J2

Connector type

MIL-DTL-38999 Series 3 D38999/24

Part number E.g. (RTC-04 connector)

D38999/24WB35SN

Part number E.g. (cable connector)

D38999/26WB35PN

Table 7.3: Actuator Arm Altimeter connection technical features

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

130

RTC-04 connection to Type A actuator

Description

Switch common

Retract

Extend

Actuator power Out GND

Actuator power Out +28V

Limit Switch common

Altimeter

GND

Not Used

+ 28V. DC

28V DC Return

Not Used

Table 7.4: Connector pinout for Type A actuator

To automatically retract the actuator by the altimeter radar alarm, short pins 7 and 8 of this connector.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

131

RTC-04 connection to Type B actuator

Description

Not Used

Down indicator

Up command

GND Chassis

Up indicator

Down command

Altimeter

GND

Not Used

+28V. DC

28V. DC Return

Not Used

Table 7.5: Connector pinout for Type B actuator

To automatically retract the actuator by the altimeter radar alarm, short pins 7 and 8 of this connector.

7.2.2.3 Alarms

The RTC-04 Remote Control shows transmitter alarms. When there is an alarm there will be a point in the profile screen.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

132

7.3 RS-485 Operation 7.3.1 PC Control Operation

The UDT-02 can be controlled remotely from a computer via RS-485 commands using the RTC connector.
The port must be configured as; 8 bits, 1 stop bit, no parity and 9600bps.

In the transmitter you need to select the RTC-04 remote control.

First you need to check the transmitter configuration by sending the following command:
0x7D 0x04 0x01 0xB8 CHK 0x7D

The transmitter answers a message with the following format:

0x7D 0x07 0x22 WW XX YY ZZ CHK 0x7D

The bytes WW XX YY ZZ can be seen as a 32 bit word. In this word the meaning of the bits are (MSB first)

31-26 => not of interest

25-20 => profile enable/disable

Bit 25 => Profile 7 enable/disable

Bit 24 => Profile 6 enable/disable

Bit 23 => Profile 5 enable/disable

Bit 22 => Profile 4 enable/disable

Bit 21 => Profile 3 enable/disable

Bit 20 => Profile 2 enable/disable

19 => PA at HIGH POWER

18 => PA at LOW POWER

17 => PA at MEDIUM POWER

16-9 => not of interest

8 => RF status (0:OFF 1:ON)

7 => ON/OFF status (1:OFF 0:ON)

6-0 => selected profile

Bit 6 => Profile 7 selected

Bit 5 => Profile 6 selected

Bit 4 => Profile 5 selected

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

133

Bit 3 => Profile 4 selected Bit 2 => Profile 3 selected Bit 1 => Profile 2 selected Bit 0 => Profile 1 selected

CHK is the XOR of all the previous bytes, excluding the first byte with value 0x7D.

The message that you can send from the PC to the transmitter to change its configuration must have the following format:

0x7D 0x07 0x23 WW XX YY ZZ CHK 0x7D

The bytes WW XX YY ZZ can be seen as a 32 bit word. In this word the meaning of the bits are (MSB first)

26-24 => profile select

Profile 1 => 001 Profile 2 => 010 Profile 3 => 011 Profile 4 => 100 Profile 5 => 101 Profile 6 => 110 Profile 7 => 111

27 => ON/OFF (0:OFF 1:ON) 28 => RF ON/OFF (0:OFF 1:ON) 29 => PA at LOW POWER 30 => PA at MID POWER 31 => PA at HIGH POWER 23-0 => not interesting

CHK must be set to the XOR of all the previous bytes, excluding the first byte with value 0x7D.

The transmitter will answer a message with the following format:

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

134

0x7D 0x07 0x32 WW XX YY ZZ CHK 0x7D

The bytes WW XX YY ZZ can be seen as a 32 bit word. In this word the meaning of the bits are (MSB first)

31-26 => not of interest

25-20 => profile enable/disable

Bit 25 => Profile 7 enable/disable

Bit 24 => Profile 6 enable/disable

Bit 23 => Profile 5 enable/disable

Bit 22 => Profile 4 enable/disable

Bit 21 => Profile 3 enable/disable

Bit 20 => Profile 2 enable/disable

19 => PA at HIGH POWER

18 => PA at LOW POWER

17 => PA at MEDIUM POWER

16-9 => not of interest

8 => RF status (0:OFF 1:ON)

7 => ON/OFF status (1:OFF 0:ON)

6-0 => selected profile

Bit 6 => Profile 7 selected

Bit 5 => Profile 6 selected

Bit 4 => Profile 5 selected

Bit 3 => Profile 4 selected

Bit 2 => Profile 3 selected

Bit 1 => Profile 2 selected

Bit 0 => Profile 1 selected

An important note to keep in mind. As the communication is halfduplex, and the master is the transmitter, to send a command to the transmitter you must wait to receive a message first, wait 20 ms, and send only one message.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

135

Mechanical Dimensions

Chapter 8: Mechanical Dimensions
In this chapter, the mechanical drawings of the units described in this manual are included.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

136

8.1 UDT-02 Transmitter

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

137

8.2 PA Standard and PA Ultralinear Power Amplifiers

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

138

8.3 PA Standard and PA Ultralinear Power Amplifiers Installation
ISO 14581 M4 (10 Units)

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

139

8.4 RTC-04 Remote Control

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

140

8.5 CLTX-01 Support

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

141

8.6 CLTX-02 Support Installation

ISO 14581 M4 (8 Units)

ISO 14581 M3x8 (6 Units)

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

142

8.7 GPS-01 Antenna & Receiver

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

143

8.8 CELLULAR DATALINK Antenna General

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

144

8.9 CELLULAR DATALINK Antenna Base

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

145

8.10 CELLULAR DATALINK Antenna with AIRFILM

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

146

Chapter 9: Preventive Maintenance

To ensure system longevity, it is highly recommended that the following preventive maintenance procedures be done at the appropriate time.

9.1 Maintenance Schedule

Procedure Inspect wiring

Yearly

Inspect the cables connection

Inspect the antenna connection

Quarterly

Monthly

Prior each use (*)

Table 10.1. Maintenance Schedule table

(*) If the UDT-02 installation is constantly changed, prior to each use make sure the RF output is loaded.
9.2 Maintenance Procedures
Quarterly, the following inspections should be done:
· Inspect antenna installation to ensure all components are secure and in good conditions.
· Inspect cables and connections.
9.3 Spare Parts
The transmitter system has no user replaceable parts. Contact SVP Broadcast Microwave for all service and repair inquiries.
Contact email: info@svpbm.com Note: Any attempts to service individual components may make the warranty void.

UDT-02 UHD HEVC Digital Camera Transmitter

MANUAL V1.1

147

Warranty

Chapter 10: Warranty
10.1 Warranty information
Under recommended use and service, all SVP Broadcast Microwave products are warranted against defects in material and workmanship to twenty-four (24) months from the date of original shipment. SVP Broadcast Microwave’s obligation is limited to repairing or replacing, at our plant, products, which prove to be defective during the warranty period. Under no circumstances shall the warranty be transferred or assigned to any third party unless consent in writing has first been obtained from SVP Broadcast Microwave. SVP Broadcast Microwave shall not be under any liability for warranty in respect to any equipment, which shall be sold by the Customer to any third party unless otherwise agreed in writing. SVP Broadcast Microwave is not liable for consequential damage resulting from the use of SVP Broadcast Microwave equipment.
10.2 Claim for damage in shipment
Your unit should be inspected and tested as soon as it is received. Claims for damage should be filed with carrier.
10.3 Return procedures
All claims under warranty must be made promptly after occurrence of circumstances giving rise to the claim and must be received within the applicable warranty period by SVP Broadcast Microwave or its authorized representative. SVP Broad

Documents / Resources

SVP UDT-02 Wireless Camera Transmitter [pdf] Instruction Manual
UDT-02 Wireless Camera Transmitter, UDT-02, Wireless Camera Transmitter, Camera Transmitter, Transmitter

References

User Manual

SVP UDT-02 Wireless Camera Transmitter

Specifications

Product Information

FAQs

Introduction

Technical features

How to order

Remote Control

Mechanical Dimensions

Warranty

Documents / Resources

References

Leave a comment

Cancel reply