SHN055B HDMI Display Module
“
Specifications
| Display Size (Diagonal) | 5.5 inch |
|---|---|
| Display Type | RGB Stripe |
| Display Mode | WD5 EA5 F0 1 & GT1 1 5 1 |
| Color | 16.7M |
| Pixel Arrangement | WD5 EA5 F0 1 & GT1 1 5 1 |
| Driver IC | GT1151 |
| Interface Type | HDMI + Type-C, USB |
| Backlight Type | AMOLED |
Product Usage Instructions
1. Installation
Ensure the device is powered off before installation. Connect
the HDMI and Type-C cables to the respective ports on the display
module.
2. Powering On
Power on the display module by supplying the LCD supply voltage
within the specified range of 5.0V. Make sure the operating
temperature is above -20°C.
3. Touch Functionality
The touch panel supports up to 5 touch points. Connect the USB
interface for touch functionality. Ensure the surface hardness
meets your requirements.
4. Display Settings
Adjust the display settings such as brightness, contrast, and
color temperature to suit your preferences using the connected HDMI
interface.
Frequently Asked Questions (FAQ)
Q: What is the maximum storage temperature for the display
module?
A: The maximum storage temperature is 80°C.
Q: How many touch points does the touch panel support?
A: The touch panel supports up to 5 touch points.
Q: How can I adjust the display settings?
A: You can adjust the display settings using the connected HDMI
interface.
“`
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
Surenoo HDMI Display Module Series
Model No.: SHN055B-10801920
USER MANUAL
Please click the following image to buy the sample
Shenzhen Surenoo Technology Co.,Ltd. www.surenoo.com
Reference Links
Surenoo HDMI Display Module Selection Guide
www.surenoo.com
P 01
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
1GENERAL INFORMATION
Item of general information Display Size (Diagonal) Display Type Display Mode
Recommended Viewing Direction Module Size (W×H) Active Area (W×H)
Number of Pixels (Resolution) Pixel Pitch (W×H)
Color Pixel Arrangement Driver IC
Interface Type Color Numbers Backlight Type
Model No.: SHN055B-10801920
Contents 5.5
AMOLED AMOLED ALL VIEW 76.00×138.00 68.31×121.44 1080(RGB)×1920
RGB Stripe
WD5 EA5 F0 1 & GT1 1 5 1
HDMI + Type-C 16.7M –
Unit inch
o’clock mm mm Pixels mm –
www.surenoo.com
P 02
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
2EXTERNAL DIMENSIONS
10.00
Model No.: SHN055B-10801920
138.00 (Frame)
121.65 VA
6.40
76.00 (Frame) 68.60 VA
3.70
AMOLED
MIPI 4 -Lane
Dr iver
WD5 EA5 F0 1 & GT1 1 5 1
AMOLED (On-Cell Touch) + Frame THIS DRAWING IS PROPERTY OF SHENZHEN SURENOO TECHNOLOGY CO.,LTD., IT CANNOT BE REPRODUCED WITHOUT PERMISSION.
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
BOE BB0 5 5 FHM-T0 0 -6 P0 1
USB Type-C
HDMI
www.surenoo.com
Micro USB P 03
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
3ABSOLUTE MAXIMUM RATINGS
Parameter of absolute
Symbol
Min
maximum ratings
Max
Unit
LCD supply voltage
VDD
5.0
5.0
V
Operating temperature
Top
-20
Storage temperature
Tst
-30
70
80
Humidity
RH
–
90%(Max 60) RH
Note: Absolute maximum ratings mean the product can withstand short-term, not more than
120 hours. If the product is a long time to withstand these conditions, the life time would be
shorter.
www.surenoo.com
P 04
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
4TOUCH CHARACTERISTICS
Item of CTP characteristics
Specification
Panel Type
On-Cell Touch
Resolution
1080 × 1920
Surface Hardness
–
Transparency
82%
Driver IC
GT1151
Interface Type
USB
Support Points
5
Model No.: SHN055B-10801920
Unit
Remark
–
–
pixel
–
–
–
–
–
–
–
–
–
–
–
www.surenoo.com
P 05
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
5ELECTRO-OPTICAL CHARACTERISTICS
Item of
electro-optical Symbol Condition Min. Typ. Max. Unit Remark Note
characteristics
Response time
Tr+Tf
–
35
45
ms
FIG 1.
4
Contrast Ratio
CR
=0 =0
–
800
–
–
FIG 2.
1
Luminance uniformity WHITE Ta=25
–
80
–
%
FIG 2.
3
Surface Luminance
Lv
–
600
– cd/m2 FIG 2.
2
CIE (x, y) chromaticity
White
White x White y
=0 =0
Ta=25
0.277 0.297 0.317 0.297 0.317 0.337
–
FIG 2.
5
=90(12 o’clock)
–
80
–
deg
Viewing =270(6 o’clock) angle range =0(3 o’clock)
CR 10
–
80 80
–
deg
–
deg
FIG 3.
6
=180(9 o’clock)
–
80
–
deg
NTSC ratio
–
–
60
70
–
%
–
–
Note 1. Contrast Ratio(CR) is defined mathematically by the following formula. For more information see FIG 2.:
Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying
white. For more information see FIG 2.
Lv=Average Surface Luminance with all white pixels (P1,P2,P3,P4,P5,P6,P7,P8,P9) Note 3. The uniformity in surface luminanceWHITEis determined by measuring
luminance at each test position 1 through 9, and then dividing the maximum luminance of
9points luminance by minimum luminance of 9 points luminance. For more information see
FIG 2.
www.surenoo.com
P 06
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
Note 4. Response time is the time required for the display to transition from White to black(Rise Time, Tr) and from black to white(Decay Time, Tf). For additional information see FIG 1. Note 5. CIE (x, y) chromaticity ,The x,y value is determined by screen active area position 5. For more information see FIG 2. Note 6. Viewing angle is the angle at which the contrast ratio is greater than a specific value. For TFT module, the specific value of contrast ratio is 10.The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 3. Note 7. For Viewing angle and response time testing, the testing data is base on Autronic-Melchers’s ConoScope. Series Instruments. For contrast ratio, Surface Luminance, Luminance uniformity and CIEthe testing data is base on BM-7 photo detector. Note 8. For TN type TFT transmissive module, Gray scale reverse occurs in the direction of panel viewing angle. FIG.1. The definition of Response Time
www.surenoo.com
P 07
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
FIG.2. Measuring method for Contrast ratio, surface luminance, Luminance
uniformity, CIE (x , y) chromaticity
A : H/6 ; B : V/6 ; H,V : Active Area(AA) size Measurement instrument: BM-7; Light spot size=5mm, 350mm distance from the LCD surface to detector lens.
FIG.3. The definition of viewing angle
www.surenoo.com
P 08
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
6INPUT TIMING
Parameter
DCLK frequency@ Frame rate=60Hz Horizontal display area 1 Horizontal Line HSYNC pulse width
HSYNC Back Porch (Blanking) HSYNC Front Porch Vertical display area VSYNC period time VSYNC pulse width
VSYNC Back Porch (Blanking) VSYNC Front Porch
Symbol
DCLK thd th thpw thb thfp tvd tv tvpw tvb tvfp
Min.
–
–
–
Value Typ.
141.12 1080 1200 20 50 50 1920 1960 10 20 10
Max.
–
Unit
MHz
DCLK
–
DCLK
–
DCLK
–
DCLK
–
DCLK
H
–
H
–
H
–
H
–
H
www.surenoo.com
P 09
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
7RELIABILITY TEST CONDITIONS
No.
Test Item
Test Condition
1 High Temperature Storage
80/120 hours
2
Low Temperature Storage
-30/120 hours
3 High Temperature Operating
70/120 hours
4 Low Temperature Operating
-20/120 hours
5 Temperature Cycle Storage -20(30min.)~25(5min.)~70(30min.)×10cycles
AInspection after test:
Inspection after 2~4 hours storage at room temperature, the sample shall be free from
defects:
Air bubble in the LCD;
Sealleak;
Non-display;
Missing segments;
Glass crack;
Current is twice higher than initial value.
BRemark:
The test samples should be applied to only one test item.
Sample size for each test item is 5~10pcs.
Failure Judgment Criterion: Basic Specification, Electrical Characteristic, Mechanical
Characteristic, Optical Characteristic.
www.surenoo.com
P 10
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
8INSPECTION CRITERION
This specification is made to be used as the standard of acceptance/rejection criteria for TFT-LCD/IPS TFT-LCD module product, and this specification is applicable only in the case that the size of module equal to or exceed than 4.3 inch. 8.1 Sample plan Sampling plan according to GB/T2828.1-2003/ISO 2859-11999 and ANSI/ASQC Z1.4-1993,normal level 2 and based on: Major defect: AQL 0.65 Minor defect: AQL 1.5 8.2 Inspection condition Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45°against perpendicular line. (Normal temperature 20~25and normal humidity 60 ±15%RH ) 8.3 Definition of Inspection Item. A Definition of inspection zone in LCD.
Zone A: character/Digit area
www.surenoo.com
P 11
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
Zone B: viewing area except Zone A (Zone A + Zone B=minimum Viewing area)
Zone C: Outside viewing area (invisible area after assembly in customer’s product)
Fig.1 Inspection zones in an LCD
Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for
quality and assembly of customer’s product.
B Definition of some visual defect
Because of losing all or part function, bad pixel dots appear bright and the
Bright dot size is more than 50% of one dot in which LCD panel is displaying under
black pattern.
Dark dot
Dots appear dark and unchanged in size in which LCD panel is displaying under pure red, green, blue picture, or pure whiter picture.
8.4 Major Defect
Item No.
Items to be inspected
Inspection standard
Classification of defects
1) No display
2) Display abnormally
3) Missing vertical, horizontal segment
1
Functional defects 4) Short circuit
5) Excess power consumption 6)Backlight no lighting, flickering and abnormal
major
lighting
2
Missing
Missing component
3
Outline dimension
Overall outline dimension beyond the drawing is not allowed
www.surenoo.com
P 12
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
8.5 Minor Defect
Item No.
1
Items to be inspected
Inspection standard
Classification of defects
Bright dot /dark dot
defect
Zone
Acceptable Qty
A+B
4.37″ 710.1″ 10.1″
C
Bright pixel dot
1
2
3
Acceptable
Dark pixel dot
4
4
4
2bright dots adjacent
0
0
0
2dark dots adjacent
0
0
0
Total bright and dark dots 5
6
7
Note: Minimum distance between defective dots is more than 5mm;
Pixel dots’ function is normal, but bright dots caused by foreign
material and other reasons are judged by the dot defect of 5.2.
Zone
Acceptable Qty
A+B
Size(mm)
4.3″7″
710.1″
10.1″
C
0.2
Acceptable Acceptable Acceptable
Minor
Acceptable
2
0.20.5
4
5
6
Minor
0.5
0
0
0
Note: 1. Minimum distance between defective dots is more than 5 mm; 2. The quantity of defect is zero in operating condition.
Zone
Acceptable Qty
Size (mm)
A+B
Length Width 4.3″7″
710.1″
10.1″
C
Linear
3
defect
Ignore W0.05 Acceptable Acceptable Acceptable
Minor
Acceptable
L5.0 0.05
4
5
6
W0.1
L5.0 W0.1
0
0
0
www.surenoo.com
P 13
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
5.4.1 Polarizer Position
( i) Shifting in position should not exceed the glass outline
dimension.
( ii ) Incomplete covering of the viewing area due to shifting is not
allowed.
5.4.2 Dirt on polarizer
Dirt which can be wiped easily should be acceptable.
5.4.3 Polarizer Dent & Air bubble
Zone
Acceptable Qty
A+B
Size(mm)
4.3″7″
710.1″
10.1″
C
0.2
Acceptable Acceptable Acceptable
Acceptable
0.20.5
4
5
6
4
Polarizer defect
0.5
0
5.4.4 Polarizer scratch
0
0
Minor
(i) If the polarizer scratch can be seen after cover assembling
or in the operating condition, judge by the linear defect of 5.3.
( ii )If the polarizer scratch can be seen only in non-operating
condition or some special angle, judge by the following:
Zone
Acceptable Qty
Size (mm)
A+B
Length Width 4.3″7″
710.1″
10.1″
C
Acceptable
Ignore W0.05 Acceptable Acceptable Acceptable
1.0L 0.05
5.0 W0.20
4
5
6
L5.0 W0.2
0
0
0
MURA
Using 3% ND filter, it’s NG if it can be seen in R,G,B picture.
5
White/Black dotMURA
Visible underND3%D0.15mm, Acceptable 0.15mm<D0.5mm, N4D>0.5mm, Not allowable.
Minor
www.surenoo.com
P 14
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
(i) Crack Cracks are not allowed.
(ii) TFT chips on corner
Model No.: SHN055B-10801920
Minor
Minor
6
Glass defect
X 3.0
Y 3.0
Z Not more than the thickness of glass
Acceptable N3
Chips on the corner of terminal shall not be allowed to extend
into the ITO pad or expose perimeter seal.
(iii) Usual surface crack
X
Y
Z
Acceptable
1.5
1.5
Not more than the thickness of glass
N4
It is only applicable to the upper glass of LCD.
Minor
www.surenoo.com
P 15
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.: SHN055B-10801920
8.6 Module Cosmetic Criteria
Item No.
1 2
3
4 5 6
7
8 9 10
Items to be inspected
Difference in Spec. Pattern peeling
Soldering defects
Resist flaw on PCB FPC gold finger Backlight plastic frame
Marking printing effect Accretion of metallic Foreign matter Stain Plate discoloring
Inspection Standard
Not allowable No substrate pattern peeling and floating No soldering missing No soldering bridge No cold soldering Visible copper foil (0.5 mm or more) on substrate pattern is not allowed No dirt, breaking, oxidation lead to black No deformation, crack, breaking, backlight positioning column breaking, obvious nick. No dark marking, incomplete, deformation lead to unable to judge
No accretion of metallic foreign matter (Not exceed 0.2mm)
No stain to spoil cosmetic badly No plate fading, rusting and discoloring
Classification of defects
Major Major Major Major Minor
Minor
Major
Minor
Minor
Minor
Minor Minor
1. Lead parts
a. Soldering side of PCB Solder to form a `Filet’ all around the lead. Solder should not hide the lead form perfectly.
b. Components side(In case of `Through Hole PCB’) Solder to reach the Components side of PCB.
Minor Minor
2. Flat packages
Either `Toe'(A) or `Seal'(B)of the lead to be covered by “Filet”. Lead form to be assume over Solder.
Minor
11 3. Chips
(3/2) H h (1/2) H
Minor
4. Solder ball/Solder splash
a. The spacing between solder ball and the conductor or solder pad h 0.13 mm. The diameter of solder ball d0.15 mm.
b. The quantity of solder balls or solder splashes isn’t beyond 5 in 600 mm2. c. Solder balls/Solder splashes do not violate minimum electrical clearance.
Minor Minor Major
www.surenoo.com
P 16
Documents / Resources
 |
Surenoo SHN055B HDMI Display Module [pdf] User Manual SHN055B-10801920, SHN055B HDMI Display Module, SHN055B, HDMI Display Module, Display Module, Module |