Specifications
- Operating Voltage: 3 VDC
- Battery Size: CR2025
- Operating Frequency: 868 MHz
- FCC ID#: 2AHST-RF28XX01
Product Usage Instructions
Safety
Ensure to follow safety precautions when installing and using
the product. Do not expose the Push Button Switch or Controller to
moisture. Always disconnect power before making any
connections.
Remote Set-Up Instructions
- Follow illustrated steps to remove the Battery Tray from the
Push Button Switch. - Insert the provided 3V battery into the Push Button
Switch.
Controller Set-Up Instructions
- Disconnect power to the Controller.
- Loosen the labeled terminal screws on top of the Controller
using a small flathead screwdriver. - Match the light strip wires with the labeled slots on the
Controller and securely insert and tighten the wires in the
terminal. - Turn on the power and wait for the light strip to illuminate.
Check connections if the light does not come on.
Battery Replacement Instructions
- Follow illustrated steps to replace the battery in the Push
Button Switch. - Use a flat-head screwdriver to remove the back plate from the
housing. - Remove the PCB board from the front housing.
- To replace the battery, push out the old battery and insert a
new 3V (CR2025) battery. - Reassemble by pushing the PCB board back into the front plate
along with the power button and then placing the back plate back
into position.
Battery Safety
If you stop using the product, remove the batteries and keep
them out of reach of children.
FAQ
A: The operating voltage of the Push Button Switch is 3 VDC.
A: Press and hold the Pairing Switch on both the Push Button
Switch and the Controller simultaneously until they are paired.
Q: Can I use this product outdoors?
A: It is not recommended to expose the Push Button Switch or
Controller to moisture, so outdoor use should be avoided unless
adequately protected from the elements.
Important: Read all instructions prior to installation.
Wireless LED Dimmer Push Button Switch for EZ Dimmer Series Controllers
Parts Included
1 – 868MHz LED Dimmer Push Button Switch 1 – 3V CR2025 Battery 2 – Mounting Screws
Push Button Switch
11. On/Off/Brightness Push Button Press switch for remotely activating / controlling LED products.
Button Actions:
Single Press
Turns LEDs on/off. If the Controller Pairing Switch has been depressed, a single press on the Push Button
Switch pairs the switch to the Controller.
Hold Press
Increases or decreases LED intensity until you release, turning Controller on will remember the last memory position
Controller
12. Pairing Switch To pair Push Button Switch to Controller, press the Controller Pairing Switch once and then press Push Button Switch. Lights will blink once to indicate pairing. To unpair Push Button Switch(es), press and hold Controller Pairing Switch until lights blink twice. 23. Master/Slave Jumper Set Jumper to Master for main Controller. Master emits synchronization signal to Slave Controllers. Set Jumper to Slave to receive synchronization signal from Master Controller. Use Master for the first Controller in each zone. To achieve precise synchronization between Controllers in one zone, set additional Controllers to slave.
EZD-1C-PB Push Button Switch
Instructional Sheet
Part Number: EZD-1C-PB
Controller: EZD-4C8A or EZD-1C8A
EZD-4C8A Controller
DC INPUT 12/36VDC
Push Switch
1
2
3
EZD-1C8A Controller
CH1
GND
EZD-1C8A
Easy Dimmer Series
PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=1x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC
tc=75ºC 0.5-2.5mm²
6-7mm
INPUT 12-36VDC
Pairing Switch
EZD-1C-PB Push Button Switch
Operating Voltage
3 VDC
Battery Size
CR2025
Operating Frequency
868 MHz
FCC ID#
2AHST-RF28XX01
V+ V-
Pairing Switch
MASTER SLAVE
EZD-4C8A
Easy Dimmer Series
PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC
OUTPUT
V+ CH1 CH2 CH3 CH4
EZD-4C8A Controller Input Voltage Current Output Wattage 12~36 VDC 4 X 8A 384W(12V) 768W(24V)
1152W(36V)
EZD-1C8A Controller Input Voltage Current Output Wattage 12~36VDC 1 X 8A 96W(12V) 192W(24V)
288(36V)
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Set-Up Instructions
Safety
Remote 1. Follow illustrated steps to remove the Battery Tray.
·
Insert the 3V battery included with the Push Button Switch.
Controller
1. Make sure power to the Controller is disconnected.
·
2. Using a small flathead screwdriver, loosen the labeled
terminal screws visible on the top of the controller.
3. Matching light strip wires with labeled slots on the Controller,
insert wires and tighten terminal screws. Be sure wire
conductor, not wire insulation, is secured in terminal.
4. Turn power on and wait until light strip illuminates. If it does
not come on, check light strips and wiring connections.
DO NOT install with power applied to controller. DO NOT expose the Push Button Switch or Controller to moisture.
Battery Replacement Instructions
1. Follow illustrated steps to replace the battery.
2. Locate notch in the back plate. Use a flat-head screwdriver to remove back plate from the housing.
3. Remove PCB board completely from the front housing.
4. If replacing battery: Push old battery down-and-out of it’s slot.
5. Insert the 3V (CR 2025) battery, push PCB board back into front plate along with the power button. Push back plate into place to complete the assembly.
Battery Safety
· Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
· Even used batteries may cause severe injury or death. · Call a local poison control center for treatment information. · Non-rechargeable batteries are not to be recharged. · Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating)
or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns. · Ensure the batteries are installed correctly according to polarity (+ and -). · Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or
rechargeable batteries. · Remove and immediately recycle or dispose of batteries from equipment not used for an extended period
of time according to local regulations. · Always completely secure the battery compartment. If the battery compartment does not close securely,
stop using the product, remove the batteries, and keep them away from children.
Rev Date: V2 02/14/2025 4400 Earth City Expy, St. Louis, MO 63045
866-590-3533 superbrightleds.com
Important: Read all instructions prior to installation.
Wireless LED Dimmer Push Button Switch for EZ Dimmer Series Controllers
Connection Diagram
EZD-4C8A Controller
Instructional Sheet
Part Number:
EZD-1C-PB
Controller: EZD-4C8A or EZD-1C8A
DC INPUT
12/36VDC
(+) Power In
(-)
Pairing Switch Master/Slave Jumper
V+ V-
Pairing Switch
MASTER SLAVE
EZD-4C8A
Easy Dimmer Series
PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC
OUTPUT
V+ CH1 CH2 CH3 CH4
Common Anode Output (+) Channel 1 Output (-) Channel 2 Output (-) Channel 3 Output (-) Channel 4 Output (-)
Optional Push Switch
(See below for operation)
Pairing Switch
EZD-1C8A Controller
CH1
GND
Push Switch
EZD-1C8A
Easy Dimmer Series
PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=1x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC
tc=75ºC
0.5-2.5mm²
6-7mm
Pairing Switch
INPUT 12-36VDC
Anode Ouput (+) Channel 1 Output (-) (+)
Power In (-)
Cove Lighting Application
Power Supply
Controller connected to multiple in-line LED strips
2
Switch
Operating the Push Button Switch/Controller
1. Press “Pairing Switch” button on the Controller. Immediately press the Push Button Switch to pair it to the Controller. The LED lights wired to the Controller will blink when the pairing is complete.
2. Multiple Push Button Switches can be paired to a Controller, and Push Button Switches can be paired to multiple Controllers. If multiple Controllers paired to a Push Button Switch are not in sync, unpair and then pair until Controllers and lights are in sync.
Wireless Signal to Controller
Rev Date: V2 02/14/2025 4400 Earth City Expy, St. Louis, MO 63045
866-590-3533 superbrightleds.com
Important: Read all instructions prior to installation.
Wireless LED Dimmer Push Button Switch for EZ Dimmer Series Controllers
Example Diagrams
(1) Single Color 24VDC Application / EZD-4C8A
From
To Additional Controllers 24VDC Out
_
_
+
+
_
_
+
+
_ +
Power
Supply
24VDC In
_
_
_
_
_
+
+
+
+
+
DC INPUT 12/36VDC
V+ V-
Pairing Switch
MASTER SLAVE
EZD-4C8A
Easy Dimmer Series
PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC
OUTPUT
V+ CH1 CH2 CH3 CH4
_
_
_
_
_
+
+
+
+
+
_
_
_
_
_
+
+
+
+
+
Instructional Sheet
Part Number:
EZD-1C-PB
Controller: EZD-4C8A or EZD-1C8A
(2) Four Color 12VDC Application / EZD-4C8A
From
To Additional Controllers 12VDC Out
_
_
+
+
_
_
+
+
_ +
Power
Supply
12VDC In
_
_
_
_
_
+
+
+
+
+
DC INPUT 12/36VDC
V+ V-
Pairing Switch
MASTER SLAVE
EZD-4C8A
Easy Dimmer Series
PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC
OUTPUT
V+ CH1 CH2 CH3 CH4
_
_
_
_
_
+
+
+
+
+
_
_
_
_
_
+
+
+
+
+
++
(3) Single Color 12VDC Application / EZD-1C8A
Optional Push Switch (See below for operation)
Optional Push Switch
Single Press
Turns LEDs on/off
Hold Press
Increases or decreases LED intensity until you release
GND
Push Switch
EZD-1C8A
Easy Dimmer Series
PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=1x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC
tc=75ºC 0.5-2.5mm²
6-7mm
Pairing Switch
CH1
INPUT 12-36VDC
+
NFLS-NW300-WHT-LC2
From Power Supply 12 VDC In
Rev Date: V2 02/14/2025 4400 Earth City Expy, St. Louis, MO 63045
866-590-3533 superbrightleds.com
Documents / Resources
 |
superbrightleds EZD-1C-PB Wireless LED Dimmer Push Button Switch [pdf] Instruction Manual EZD-1C-PB, EZD-4C8A, EZD-1C8A, EZD-1C-PB Wireless LED Dimmer Push Button Switch, EZD-1C-PB, Wireless LED Dimmer Push Button Switch, Dimmer Push Button Switch, Push Button Switch, Button Switch |