Sunricher DT8 Push Button Tunable White DALI Controller Instruction Manual

Click to get 100% WW and 0% CW. Press and hold down to increase WW and decrease CW.
Scene Button 1: Click to recall a predefined or saved Scene of the selected Group, and press and hold down to save the scene to the selected Group.

Press and hold down to turn down the brightness of the group.
Click to get 100% CW and 0% WW. Press and hold down to increase CW and decrease WW.

Scene Button 2: Click to recall predefined or saved Scene of the selected Group, and press and hold down to save scene to the selected Group.
Rear side: Rotary Switch for Assigning Group (Total 16 Groups)

Rear side: Rotary Switch for Assigning Scene (Total 16 Scenes)
Please assign the devices on the DALI circuit to a DALI group (0-15) with the DALI master controller first.

Set starting Scene number via rotary switch on the back: (0-15 selectable)
Please predefine DALI scenes (0-15) to the devices on the DALI circuit with the DALI master controller first.

Operate WW CW buttons to select a CCT and brightness.
Press and hold down buttons S1-S2 (e.g. S2) until the LED light connected with the controlled DALI devices flashes, indicating the scene is saved successfully.

OVERWIEW

Product Data

Output	DALI signal
Power Supply	Supply By DALI Bus
Operation Current	30mA
Operating temperature	0-40°C
Relative humidity	8% to 80%
Dimensions	80x80x26.6mm

Push button DALI DT8 CCT controller, color type TC

Ultra slim and luxury design
Material and finishing color can be customized

With backlighting design, easy to find even in dark night
DALI bus powered, no extra power supply required
Each channel DALI bus can install multiple controllers

Enables to selection and control of 1 DALI group from a total 16

DALI groups

Enables to select and control 2 DALI scenes from a total 16

DALI scenes

Easy installation with mounting bracket
Waterproof grade: IP20

Installation

Safety & Warnings

DO NOT install with power applied to the device.
DO NOT expose the device to moisture

Operation

Do wiring according to connection diagram correctly.
Set starting Group number via rotary switch on the back: (0-15 selectable)
1. This DALI push button controller enables dimming commands and DT8 commands to be sent to One Group of devices on the DALI circuit. A rotary switch on the back is used to select the DALI Group you would like to control and set the starting Group number, and a total 16 Groups (0-15) can be selected.
2. When the rotary switch arrow position is at 0, the controller controls all devices on DALI circuit through broadcast.
3. When the rotary switch arrow position is at X except 0 (1-15), the controller controls devices in Group X-1.Q
For example: Rotary switch arrow at 1, the controller controls devices in Group 0. Rotary switch arrow at 15, the controller controls devices in Group 14. Please refer to the detailed Group setting table as follows:

Rotary Switch Position	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15
DALI Group Selected	Broadcast	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14

Note: Please assign the devices on the DALI circuit to a DALI group(0-15) with the DALI master controller first.

Set starting Scene number via rotary switch on the back: (0-15 selectable)
This DALI push button controller enables Scene selection commands for up to four Scenes to be sent to the DALI circuit by 2 Scene buttons S1, S2. A rotary switch on the back is used to select Scenes you would like to control and set the starting scene number, and a total 16 Scenes (0-15) can be selected.
When the rotary switch arrow position is at X (0-15), Scene button S1 controls DALI Scene X, S2 controls DALI Scene X+1.

For example Rotary switch arrow at 0, button S1 controls DALI Scene 0, S2 controls DALI Scene 1. Rotary switch arrow at 15, button S1 controls DALI Scene 15, S2 controls DALI Scene 0.Please refer to the detailed Scene setting table as follows:

Rotary Switch Position	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15
Scene assigned to S1	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15
Scene assigned to S2	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	0

Note: please predefine DALI scenes(0-15) to the devices on the DALI circuit with the DALI master controller first.

Save Scenes

FAQ

Q: How do I switch on a group?
A: Simply click the button associated with the group you want to switch on.
Q: How do I save a scene?

A: Follow the steps outlined in the “Save Scenes” section of the user manual, ensuring you operate the buttons correctly and observe the LED indicator.

Documents / Resources

Sunricher DT8 Push Button Tunable White DALI Controller [pdf] Instruction Manual
2422NK8-CCT-G1-S2, 09.2402K8CTGS.04766, DT8 Push Button Tunable White DALI Controller, DT8, Push Button Tunable White DALI Controller, Tunable White DALI Controller, White DALI Controller, DALI Controller

References

User Manual

Sunricher DT8 Push Button Tunable White DALI Controller

Specifications

Product Usage Instructions