Sunricher-LOGO

Sunricher 904X ZigBee Micro Smart Dimmer

Sunricher-904X-ZigBee-Micro-Smart-Dimmer-PRODUCT

Product Usage Instructions

Installation:
Follow the wiring diagram provided in the manual for installation. Ensure power is disconnected before installation.

Operation:

  1. Zigbee Network Pairing:
    • Pair the device with your Zigbee Controller or hub by following the pairing instructions.
    • Short press the Reset button 5 times to set it into network pairing mode.
    • Once paired, the connected light will indicate successful pairing.
  2. Factory Reset:
    • To reset the device manually, short press the Reset key 5 times continuously.
    • The connected light will blink 3 times to confirm the reset.
  3. TouchLink to a Zigbee Remote:
    • Press the Reset button 4 times to start Touchlink commissioning.
    • Bring the remote or touch panel within 10cm of the device.
    • Follow the remote or touch panel manual for Touchlink commissioning instructions.
    • Successful link will be indicated on the remote and the connected light will flash twice.

Important: Read All Instructions Prior to Installation Function introduction

Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (1)Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (2)Accessory 1: Wire clamp cover. Need to purchase separately. Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (3)Accessory 2: din rail bracket. Need to purchase separately.

Product Data

Input Voltage Output Voltage Output Current Size(LxWxH)
100-240VAC 100-240VAC 0.1-1.1A 42x38x16mm

Compatible Load Types

Compatible Load Types
Load Symbol Load Type Maximum Load Remarks
Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (4)  

Dimmable LED lamps

 

200W @ 230V

100W @ 110V

Due to the variety of LED lamp designs, a maximum number of LED lamps is further dependent on the power factor result when connected to the dimmer.
Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (4) Dimmable LED drivers 200W @ 230V

100W @ 110V

Maximum permitted number of drivers is 200W divided by driver nameplate power rating.
Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (5) Incandescent lighting, HV Halogen lamps 250W @ 230V

125W @ 110V

 
Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (6) Low voltage halogen lighting with electronic transformers 200W @ 230V

100W @ 110V

 

ZigBee Clusters the device supports are as follows:

Input Clusters

  • 0x0000: Basic
  • 0x0003: Identify
  • 0x0004: Groups
  • 0x0005: Scenes
  • 0x0006: On/off
  • 0x0702: Simple Metering
  • 0x0008: Level Control
  • 0x0b04: Electrical Measurement
  • 0x0b05: Diagnostics

Output Clusters

  • 0x0019: OTA
  • ZigBee AC phase cut dimmer based on latest ZigBee 3.0 protocol
  • 100-240VAC Wide Input and Output Voltage
  • Supports resistive loads, capacitive loads or inductive loads
  • 1 Channel Output, Up to 250W
  • Input and Output with Screw Terminals, Safe and Reliable
  • Both the leading edge version and the trailing edge version are available for choosing, preset by factory setting
  • Enables the control of ON/OFF and light intensity of the connected light source
  • ZigBee end device that supports Touchlink commissioning
  • Can directly pair to a compatible ZigBee remote via Touchlink without a coordinator
  • Compatible with universal ZigBee gateway products
  • Supports power metering
  • Mini Size, Easy to be Installed into a standard 86*86mm wall box

Main Features:

  • Can operate under two-wire connection with no neutral lead or three-wire connection with neutral lead
  • Advanced microprocessor control
  • Implemented algorithm of smart light source detection
  • Active power and energy metering functionality
  • Soft start function
  • Innovative minimum dimming level and startup brightness setting function
  • Works with various types of switches – momentary, toggle, three-way, etc.
  • Active element: semiconductor electronic switch
  • To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of applicable regulations
  • The Bypass is an extension unit

As a dimmer it operates under the following loads:

  • Conventional incandescent and HV halogen light sources
  • ELV halogen lamps and dimmable LED bulbs (with electronic transformers)
  • MLV halogen lamps (with ferromagnetic transformers)
  • Dimmable LED bulbs
  • Dimmable compact fluorescent CFL tube lamps
  • Supported dimmable light sources (power factor > 0.5) with minimal power of 3VA using the Bypass (depending on the type of load)

Trailing edge or leading edge dimming mode can be preset by factory setting to control following types of loads:

  • “Trailing edge” for resistive loads
  • “Trailing edge” for capacitive loads
  • “Leading edge” for inductive loads
  • Note: factory default version is trailing edge.

Safety & Warnings

  • DO NOT install with power applied to device.
  • DO NOT expose the device to moisture.

Wiring Diagram

Notes for the diagrams:

  • L – terminal for live lead
  • N – terminal for neutral lead
  • O – output terminal of the dimmer (controlling connected light source) SW – terminal for switch

Method 1: With neutral

Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (7)

Method 2: Without neutral

Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (8)

  • When using the device without neutral, the smart dimmer requires at least 20W @ 240 VAC of power consumption to operate. If the connected light has a smaller power consumption, then Bypass is needed for the device to work.

Operation

Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

Step 1: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
Step 2: Short press the “Reset” button 5 times to set it into network pairing mode. Pairing mode will last until the device is added to a network.
Step 3: Connected light will blink 5 times and then stay solid on, then the device will appear in your controller’s menu and can be controlled through controller or hub interface.

Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (9)

  • If the device had been added into the other zigbee network, please reset it first

Factory Reset Manually

  • Step 1: Short press “Reset” key for 5 times continuously.
  • Step 2: Connected light will blink 3 times to indicate successful reset.
  • Note:
    1. If the device is already at factory default settings, there is no indication when factory reset again.
    2. All configuration parameters will be reset after the device is reset or removed from the network.Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (10)

TouchLink to a Zigbee Remote

  • Step 1: Short press “Reset” button 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation.
  • Step 2: Bring the remote or touch panel within 10cm of the lighting device.
  • Step 3: Set the remote or touch panel into Touchlink commissioning, please refer to the corresponding remote or touch panel manual to learn how.
  • Step 4: There shall be indication on the remote for successful link and the connected light will flash twice.Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (11)

Note: 

  1. Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
  2. TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
  3. To control by both gateway and remote, add remote and device to network first, then TouchLink.
  4. After TouchLink, the device can be controlled by the linked remotes.

Learning to a Zigbee Green Power Remote

  • Step 1: Short press “Reset.” button 4 times to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation.
  • Step 2: Set the green power remote into Learning mode, please refer to its manual.
  • Step 3: Connected light will flash twice to indicate successful learning. Then the remote can control the device.
  • Note: Each device can learn to max. 20 Zigbee Green Power remotes.Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (12)

Delete Learning to a Zigbee Green Power Remote

  • Step 1: Short press “Reset” button 3 times to start delete Learning mode (connected light flashes slowly), 180 seconds timeout, repeat the operation.
  • Step 2: Set the paired green power remote into Learning mode, please refer to its manual.
  • Step 3: Connected light will flash 4 times to indicate successful deletion.Sunricher-904X-ZigBee-Micro-Smart-Dimmer-FIG- (13)

Minimum and Startup Brightness Setting Button

Set minimum brightness: Adjust brightness to a desired level, press and hold down the button for 3 seconds to set it as minimum brightness, the connected load will flash to confirm successful setting, then the dimming range is between this minimum brightness and 100%.

Delete minimum brightness: Adjust brightness to 100%, press and hold down the button for 3 seconds to delete the previously set minimum brightness, the connected load will flash to confirm successful deleting, then the dimming range is between 1% and 100%.

Set Startup Brightness: adjust the brightness of connected load to a desired level between 1%-50%, then double click “Min. set” key to set the brightness adjusted as startup brightness, then the load will first go to startup brightness when turned on every time, then drop down to the brightness before last time turned off.

Delete Startup Brightness: adjust the brightness of connected load to 0%, then double click “Min. set” key to delete the previously set startup brightness.

Note: startup brightness setting function is to avoid the phenomenon that some dimmable LED drivers can not be turned on after dimmed to a low level and turned off. Once setting a startup brightness, if the startup brightness is higher than the dimmed level before turned off, the driver will first go to the startup brightness after turned on, then drop down to the dimmed level. If the startup brightness is lower than the dimmed level before turned off, the driver will directly go to the dimmed level after turned on.

Controlled by a push switch
Once connected with a push switch, click the push switch to switch ON/OFF, press and hold it down to
increase/decrease light intensity.

OTA
The device supports firmware updating through OTA, and will acquire new firmware from the zigbee controller or hub every 10 minutes automatically.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The distance between user and products should be no less than 20cm

FAQS

Q: Do I need to purchase additional accessories for installation?
A: Yes, you may need to purchase Wire clamp cover and din rail bracket separately for installation.

Q: What is the power requirement for using the device without a neutral connection?
A: The smart dimmer requires at least 20W @ 240 VAC of power consumption to operate without a neutral connection. If the connected light has a smaller power consumption, a Bypass is needed for the device to work.

Documents / Resources

Sunricher 904X ZigBee Micro Smart Dimmer [pdf] User Guide
904X, 904X ZigBee Micro Smart Dimmer, ZigBee Micro Smart Dimmer, Micro Smart Dimmer, Smart Dimmer

References

Leave a comment

Your email address will not be published. Required fields are marked *