SUNRICHER 65W 2 Channels Zigbee LED Driver Instruction Manual
65W 2CH Zigbee NFC Enabled LED Driver(Constant Current)
Important: Read All Instructions Prior to Installation
Product Data
|
Output |
LED Channel | 2 |
| DC Voltage | 6-54V | |
| Current | 500-1500mA via NFC setting; Min.current gear lower to 0.1mA,Default 1050mA | |
| Current Accuracy | ±3%( ±1%@Certain full load) @ full load | |
| Rated Power | Max. 65W | |
|
Input |
Voltage Range | 200-240VAC/200-240VDC |
| Absolute Voltage Range | 176-264VAC/176-280VDC | |
| Frequency Range | 0/50/60Hz | |
| Power Factor (Typ.) | > 0.98 @ 230VAC Full load | |
| Total Harmonic
Distortion |
THD ≤ 6% (@ full load / 230VAC) | |
| Efficiency (Typ.) | ＞90% @ 230VAC full load | |
| AC Current (Typ.) | 0.4A @ 230VAC | |
| Inrush Current (Typ.) | Max. 9.68A at 230VAC; 70μs duration | |
| Leakage Current | < 5mA /230VAC | |
| Standby Power Consumption | ＜0.5W | |
| Anti Surge | L-N:2KV | |
|
Control |
Dimming Interface | Zigbee |
| Dimming Range | 0.01%-100%@ Max current | |
| Dimming Method | Amplitude/CCR dimming | |
| Dimming Curve | Linear/ Logarithmic optional |
|
Protection |
Short Circuit | Yes, remove the fault conditions and re-power the device |
| Over Current | Yes, remove the fault conditions and re-power the device | |
| Over Temperature | Yes, remove the fault conditions and re-power the device | |
|
Environment |
Working Temp. | -25℃ ~ +45℃ |
| Max. Case Temp. | TC=85℃ (Ta=”45℃”) | |
| Working Humidity | 10% ~ 95% RH non-condensing | |
| Storage Temp. & Humidity | -40℃ ~ +80℃, 10% ~ 95% RH | |
|
Safety & EMC |
Safety Standards | EN61347-1, EN61347-2-13 |
| Withstand Voltage | I/P-O/P: 3.75KVAC | |
| Isolation Resistance | I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH | |
| EMC Emission | En55015, EN61000-3-2, EN61000-3-3 | |
| EMC Immunity | En61547, EN61000-4-2,3,4,5,6,8,11 | |
|
Others |
MTBF |
191350H, MIL-HDBK-217F @ 230VAC full load
and 25℃ ambient temperature |
| Dimension | 123.9×78.8x30mm (L*W*H) | |
| Warranty | 5 Years |
- Dimmable LED driver, ZigBee device based on ZigBee 0 protocol
- Dimmable LED Max. output power 65W
- 500-1500mA current selectable via NFC program Min.current gear lower to 0.1mA
- Dimming curve/Power on state/Soft start/Soft off via NFC program
- Class Ⅱ power supply, full isolated plastic case
- High power factor and efficiency
- PUSH DIM function enabled
- Able to On/Off and control LED lighting luminaries‘ brightness and color temperature
- Amplitude/CCR dimming, smooth and deep dimming
- ZigBee end device that supports Touchlink commissioning
- Can directly pair to a compatible ZigBee remote via Touchlink
- Supports find and bind mode to bind a ZigBee remote
- Supports zigbee green power and can bind 20 zigbee green power switches
- Compatible with universal ZigBee gateway products
- Waterproof grade: IP20, suitable for indoor LED lighting applications
- 5 years warranty
Safety & Warnings
- DO NOT install with power applied to the
- DO NOT expose the device to
Operation–Zigbee Network
- Do wiring according to connection diagram
- This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail.
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
Step 3: power on the device, it will be set into network pairing mode (connected light flashes twice slowly), thenetwork pairing mode will last until the device is added to a zigbee network
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
- TouchLink after both added to a ZigBee network, each device can link with 30 remotes.
- To control by both gateway and remote, add remote and device to network first then
- After TouchLink, the device can be controlled by the linked
5. Removed from a Zigbee Network through Coordinator or Hub Interface
Factory Reset Manually
Step 1: Enable Pairing via NFC App or re-power on the device for 5 times continuously .
2) All configuration parameters will be reset after the device is reset or removed from the network.
Find and Bind Mode
Step 1: Re-power on the device (initiator node) 3 times to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation
Learning to a Zigbee Green Power Switch
Step 1: Re-power on the device 4 times to start Learning to GP switch mode (connected light flashes twice), 180 seconds timeout, repeat the operation.
ZigBee Clusters the device supports are as follows:
Input Clusters
- 0x0000: Basic 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes • 0x0006: On/off
- 0x0008: Level Control 0x0300: Color Control • 0x0b05: Diagnostics
Output Clusters
- 0x0019: OTA
Function setting Via “SR NFC TOOL
- Enable the Zigbee NFC drivers enter the pairing mode and add it into the Zigbee
- Factory Enable the configured Zigbee NFC driver into configuring mode.
- Besides, you can re-power the device 5 times to enable this section as
Step 3: Unlock device, enter parameters configuring page.
Note
- Do wiring according to the wiring diagram .
- Recommend setting parameters without power-on devices .
2) Please make sure your mobile phone has NFC function and enable it .
Working with “SR NFC Tool” APP
Step 1: Download the APP (searching “SR NFC Tool” from App Store and Google Playstore) .
Then open the APP .
Note: 1. Please Make sure that you have enabled NFC function with your mobile phone/ tablet .
- Please Make sure that the “NFC position” is
- Please do not power on the device before
- If you can’t download “SR NFC Tool”. Please contact with
Step 3: Unlock device, enter parameters configuring page.
Note: 1. You have to unlock the device then do some settings
- Only when the corresponding function is selected, the function interface will be displayed.
Step 4: Few parameter interface, you can choose the setting based on your requirements
Step 5: After setting, please save the selected configuration via NFC and power on the device.
Wiring Diagram
Application 1（Without PUSH
Application 2（With PUSH）
Product Dimension
Operating window
Dimming Curve
Driver Performance
Driver Performance
|
Module Number |
Ipeak |
Twidth |
Max.quantity of LED Driver per MCB B10 B13 B16 B20 B25 C10 C13 C16 C20 C25 D10 D13 D16 D20 D25 |
||||||||||||||
|
SRP-ZG9105N-65CC500-1500 |
9.68A |
70μs |
15 |
20 |
24 |
30 |
38 |
20 |
26 |
32 |
40 |
50 |
22 |
29 |
36 |
45 |
57 |
|
SRP-ZG9105N-65CCT500-1500 |
9.68A |
70μs |
15 |
20 |
24 |
30 |
38 |
20 |
26 |
32 |
40 |
50 |
22 |
29 |
36 |
45 |
57 |
Note:
- Those MCB parameters are based on ABB S200 series circuit
- For different brands and models of miniature circuit breakers, the quantity of drivers will have
- Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site
- When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires
- Type C MCB’s are strongly recommended to use with LED lighting
Update log
| Date | Version | Update content | Update by |
| 2023-9-28 | V1.0 | Initial Version | Romeo |
Read More About This Manual & Download PDF:
Documents / Resources
 |
SUNRICHER 65W 2 Channels Zigbee LED Driver [pdf] Instruction Manual 65W 2 Channels Zigbee LED Driver, 65W, 2 Channels Zigbee LED Driver, Channels Zigbee LED Driver, Zigbee LED Driver, LED Driver, Driver |