SUNPOW Jump Starter Instruction Manual

SUNPOW Jump Starter
Instruction Manual

Thank you for choosing the SUNPOW SP-JS01 16000mAh Lithium Jump Starter. Read and understand the User Guide before operating the product. Please keep the User Manual for future reference.

If you have any questions , please contact us . Email: SUN POW .S ERVIC E@hotmail.com

Warning

  1. Read and understand the User Guide before operating the unit.
  2. Do NOT replace vehicle batteries.
  3. Do NOT use as a toy.
  4. To reduce the risk of injury, close supervision is necessary when the unit is used near children.
  5. Jump for 12V vehicles , it would be hazard if for other jumping.
  6. Use of an attachment not recommended or sold by power pack manufacturer may result in a risk of fire, electric shock, or injury.
  7. Do NOT connect the two clamps together.
  8. 8.Before starting, ensure that there is no corrosion at the interface and no foreign matter adheres. Connect the main unit to the battery holder tightly to avoid the impact of the interface connection.
  9. Once you have started your vehicle, please remove the product from the car battery within 30s, otherwise it may cause damage.
  10. Do NOT Jump Start more than 3 times in a row that would damage the unit by overheating. When starting up multiple times, each start-up interval is two minutes.
  11. Do NOT use Battery Clamps to charge other devices.
  12. Do NOT place the product in an environment where the temperature may exceeds 60°C.
  13. Charge only at ambient temperature between -20°C-60°C.
  14. Do NOT expose the product to rain or place it in water.
  15. Do NOT expose product to extreme heat or fire.
  16. Do NOT operate the product in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
  17. Make sure someone should be within range of your voice or close enough to come to your aid when working with batteries.
  18. Before using the product, please remove personal metal items like rings, bracelets, necklaces, etc.
  19. To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the power pack.
  20. Do not use damaged or modified battery packs. Damaged or modified batteries may cause unpredictable behavior resulting in fire, explosion or risk of injury.
  21. Charge only using the charger provided with this unit or the same standard with the host input port.
  22. After jump start the car,don’t charge this unit immediately.
  23. Do NOT use the unit to jump start a vehicle while charging the internal battery.
  24. The battery may leak in extreme situations. If a liquid is noticed coming from product do not handle with bare hands. In case of skin contact wash with soap and water immediately. If liquid comes in contact with eyes rinse eyes with cold running water for at least 10 minutes and get medical attention immediately.
  25. Product contains lithium based battery, at end of product life dispose of product according to local regulation.

Technical Specifications

  • Dimensions: 6.7 x 3.3x 1.6 Inches
  • Weight: 1.1 Pounds
  • Battery Capacity: 1 6000mAh
  • Input: Quick Charge (5V=2A;9V=2A)
  • Output: 5V, 2.1A; Quick Charge(5V=3A;9V=2A;12V=1.5A); Jump Starting 12V vehicles
  • Charging Times: 3 Hours
  • Starting Current Rating: 300A Peak
  • Current Rating: 1500A
  • Operating Temperature: -20°C – 60°C 4

Product Description

Product Description

What’s In The Box

  • SP-JS01 Lithium Jump Starter
  • USB Charger
  • Battery Clamps
  • Micro USB Cable
  • Type-C Cable
  • User Guide

Understanding Charge LEDs

Press the power button, the battery level will indicate as follows:

table

During the charging process, the charge LEDs flashes cyclically. All LEDs are off that indicates the charging is suspended/end.

Charging the SP-JS01

  1. Plug the USB charger into the socket.
  2. Connect the SP-JS01 using the included USB Charge Cable to the USB IN port and the USB charger.

Charging the SP-JS01

Jump Starting 12V Vehicles

  1. Verify the voltage and chemistry of the battery. Connect the Battery Clamp Connector to the Jump Starter.
  2. Confirm the battery clamps are connected to the correct polarity battery terminals.
  3. Please follow the instructions of the battery clamp indicator light to perform the corresponding operations.

Jump Starting

Jump Starting

4. Try starting the vehicle.

5. Once you have started your vehicle, disconnect the battery clamps.

Charging Your Smartphone/Pad

  1. Connect the USB cable to Quick Charge Output Port.
  2. Connect to electronic products such as smartphone/pad.
  3. Press the power button to automatically identify the appropriate parameters of the electronic products, and start charging the electronic product.

Charging Your Smartphone

Switch between different modes of LED lights

  1. Long press the power button for 3 seconds to turn the flashlight “On”. Press once for strobe, again for SOS.

FAQ

FAQ

Trouble Shooting

If the following solution cannot eliminate the trouble, please stop use it and contact us

Trouble Shooting

TOXIC AND HARMFUL SUBSTANCES

TOXIC AND HARMFUL SUBSTANCES

Warranty

Sunpow provides our customers 18 months warranty from the date of its original purchase. If the device fails due to manufacturer defects, please contact us email SUNPOW.SERVICE©hatmail.com to hunch a warranty claim. We wil instruct you on how to return the product for repair/replacement.

Documents / Resources

PDF thumbnailJump Starter
Instruction Manual · Jump Starter, SP-JS01

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. I nned help, I lost my connecctor boxx that plugs into the wall receptacle, how do i get anew one

    Paul Lett l asks I nned help, I lost my connecctor boxx that plugs into the wall receptacle, how do i get anew one
    Manuals+ clarified question
    Question

    How can I get a replacement wall charger for my SUNPOW SP-JS01 jump starter?

    Answer

    To obtain a replacement USB wall charger (the "connector box") for your SUNPOW SP-JS01 jump starter, you should contact the manufacturer directly. According to the manual, you can reach their support team at: SUNPOW.SERVICE@hotmail.com.

    The technical specifications for the input are Quick Charge (5V=2A; 9V=2A). While you can use a standard third-party USB wall adapter, the manual recommends using a charger that meets these standards to ensure proper charging times (approximately 3 hours). When contacting them, mention that you have the SP-JS01 model to ensure compatibility.

  2. My charger came without the USB charger and the micro USB cable. I have to way to charge the unit.

    M. Brumwell asks My charger came without the USB charger and the micro USB cable. I have to way to charge the unit.
    Manuals+ clarified question
    Question

    What should I do if my SUNPOW Jump Starter is missing the USB charger and micro USB cable?

    Answer

    According to the "What's In The Box" section of the manual, both a USB Charger and a Micro USB Cable should be included with your SUNPOW SP-JS01 Lithium Jump Starter.

    If these items are missing from your package, you should contact SUNPOW customer service to report the missing parts or initiate a warranty claim. The manufacturer provides an 18-month warranty from the date of purchase. You can reach them at: SUNPOW.SERVICE@hotmail.com.

    In the meantime, the technical specifications indicate the unit uses a Quick Charge Input Port (5V=2A; 9V=2A). You may be able to use a standard high-quality Micro USB or Type-C cable (depending on your specific model's input port) and a compatible USB wall adapter to charge the unit while waiting for a resolution from the manufacturer.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.