Sulion 075696 Ceiling Fan with Built-in LED Light
Congratulations on your purchase
Congratulations on purchasing the latest energy-efficient ceiling fan technology. This fan uses DC current, allowing for very high energy efficiency and high air circulation volume without added noise.
- Energy efficiency: Your DC motor is the latest in fan design technology. It saves up to 70% of energy compared to fans with traditional AC motors.
- Silent operation: This fan’s DC motor uses a stabilized current, which allows it to significantly reduce operating noise. Low-heating operation: This DC motor is powered efficiently, reducing its operating temperature to under 50º C. This results in better cooling than a standard AC motor and increases its durability.
- Comfort: This fan with a DC motor incorporates a six-speed remote control that exceeds the traditional number of speeds in AC motors, allowing for a greater variety of comfort levels.
Safety precautions
Follow these instructions carefully to enjoy maximum safety in the installation and operation of this equipment.
The minimum distance between the lamp and any illuminated objects must be greater than 1m.
The electrical installation of the ceiling fan must be carried out by an authorized electrician in order to be covered by our warranty. Please remember to require your installer to test all the fan functions before you leave. In case of any doubt from the installer, do not hesitate to contact us.
This device can be used by children aged 8 years and above and people with reduced physical, sensory or mental abilities or lack of experience or knowledge, if they have been given appropriate supervision or training regarding the use of the device and they understand the dangers of its use. Children should not play with the device. The cleaning and maintenance of the device should not be carried out by children without supervision.
The fan must be installed in such a way that the blades are more than 2,3m above the ground. Make sure that there is a space of at least 30cm between the fan’s blades and any wall or other obstacle that they could hit. It is important to note that the greater the distance, the more efficient the air flow produced will be. Before contacting the technical service, it is recommended to read the troubleshooting guide included in this manual.
Any action performed for the electrical connection of the device, such as its cleaning, must be carried out after ensure in that the general power supply is disconnected, by removing the corresponding fuse or disarming the protective switch in order to ensure total isolation of the power supply.
The fan must be installed at a location on the ceiling such that the blades are at least 2.3 m above the floor and 300 mm from any object or wall. The mounting bracket must be attached to a ceiling structure that is capable of supporting a minimum of 30 kg using the two screws provided. At least 30 mm of the length of the screws must be screwed into the bracket. When deciding where to mount the fan, be sure that there is at least 30 cm of space between the fan and any wall or other obstruction that the fan blades could collide with. The greater this distance, the more effective the air flow produced. After the fan is mounted, be sure that the blades are no less than 2.3 m above the ground
The ground wire of the fan must be connected to the earth network of the installation, to avoid any derangement that may put people in danger.
Do not connect the fan’s power supply to any dimmers, potentiometers, or light switches, as it will cause the fan to malfunction and/or will damage the motor. For the electrical connection, it is necessary to incorporate a switch disconnector in accordance with the installation regulations, which ensures an omnipolar cut, directly connected to the power terminals and must have a contact separation at all its poles, which provides total disconnection under conditions of Category III overvoltage. The fan must be directly connected to a properly protected installation circuit (magnetothermal differential switch with the adequate size for the fan’s con-sumption and technical specifications). Only use the fan’s control to turn it on or stop it.
It is recommended to not use these types of fans along with gas installations simultaneously in the same room.
The fan must be not be moving and must have come to a complete stop before changing its direction of rotation. This will prevent damage to its motor and to the control unit, when applicable.
Do not insert anything that could hit the fan’s blades into its pathway while it is moving, as this could cause damage to people, damage the blades, and can offset the balance of the unit, causing vibrations and wobbling.
After installing the fan, ensure that all fastenings are secure and tightened in order to avoid any noise caused by loose elements.
Due to the fan’s movement, certain fastenings may become loose. Check all fastenings twice per year at a minimum in order to ensure that they are sufficiently tight. If necessary, they must be retightened.
If the power cord is damaged, it must be replaced by the manufacturer, its after-sales service or similar qualified personnel in order to avoid any malfunction.
Only suitable for indoors.
Replaceable LED
Replaceable driver
Replaceable receiver
Do not throw away electrical products together with household waste. We ask you to recycle the packaging at the collection points provided for this purpose. Contact local authorities or your provider for recycling advice. Thank you for recycling at the collection points provided for this manual.
Note: The important warnings and instructions indicated in this manual are not guaranteed to cover all possible conditions and situations that may occur. It must be understood that common sense, precaution, and care are factors that cannot be included in all products. These factors can and must only be provided by the user who maintains and enjoys this fan.
Device technical specifications
- Nominal voltage and frequency 220-240V~AC 50/60Hz
- Light wattage 36W
- Luminous flux 2500lm
- Light color temperature 3000-6000K
- Nº of light ON/OFF cycles 10000
- Nº of hours of light lifespan 30000h
- Protection category Class I
- Protection index IP20
- Word temperature -5 ↔ 40ºC
- Dimmable/Not dimmable Dimmable
- Maximun ceiling slope on which it can be installed 15º
- Light angle 150º
- Light Ra 80
- Bluetooth versión 4.0
- Frequency control 2.4GHz
- Speaker power 5W
- Weight 8,6kg
Preparing for installation
Note: The estimated installation time is 120 minutes. This product can only be installed by a certified electrician. Carefully separate the fan’s parts, avoiding the use of cutters or blades that could scratch any part of it.
Remote control
Syncing the receiver and the remote control for fan operation
If the receiver and transmitter of this fan are properly synchronized, the fan will work. During synchronization, the receiver recognizes the signal from the transmitter; this is called the learning process. Make sure the fan is disconnected. This is essential for the synchronization process.
Unless the synchronization process has been successful, the fan will work partially or will not work. By default, all fans have been preconfigured at the factory and should be functional once the installation is completed and the fan is turned on. If the remote control does not work after installation or during use, synchronization can be performed as indicated below. Note in any case that there could be other reasons why your fan or remote control does not work:
- Make sure all connections are correctly made.
- Make sure that the remote control contains batteries. Make sure that all switches (main and isolation) are on.
Instructions for synchronizing the receiver and the remote control
The control of this fan does not require synchronization with the receiver; the control is already factory-linked with its receiver; Universal mode and Unit mode:
Unit Mode:
This type of synchronization allows you to control two or more nearby fans independently, each with its remote control. Synchronization:
The control of this fan does not require synchronization with the receiver; the control is already factory-linked with its receiver
Universal Mode:
This type of synchronization allows you to control one or more nearby fans with the same remote control. Synchronization:
- Connect the power (wall switch) of the fan or fans that you want to control, and then just within the following 15 seconds, press the key
of the remote control for 5 continuous seconds. - A “beep” sound indicates that the connection has been executed and the equipment can function normally.
- Now, transmitter and receiver of the fan / s will have been synchronized. Turn off the fan / securrent using the switch or automatic and then turn it back on / s, this step is the one that closes the synchronization process.
It is not possible for a controller to forget a fan once it has been linked, if you want a fan to leave to obey a command, another one must be linked to “overwrite it”.
App
Thanks to Sulion Nando fan, you can select the kind of lighting you prefer for each moment to (warm, cold, specific color…) also, music played with your device (phone, laptop, Tablet…) will sound through the speaker of the fan.
Instalation
- Turn on the light of the fan
- Activate the Bluetooth from your device (phone, laptop or Tablet).
- Search the device “Sulion Nando Fan” in the list of available devices for pairing
- Download the iLink APP from Google Play or the App Store
- When opening the APP, select Configuration (1) and open Bluetooth connection (2), in the new screen search for “Sulion Nando Fan” (3) to add it in the APP.
- Once the previous step is finished, you can control the fan completely from the device; there is no need to repeat steps 3,4, and 5
App Functions:
Lamp: Allows to turn ON and OFF the light of the fan, also can change the light into RGB colors.
Color temperature: Allows to change and controlling different tones of white light.
Music: Allows to play any song stored in the device. Once the fan is paired, the music can also be played from other APPs and from an internet browser.
Scene: Allows to change among different press selcted scenes.
Note: If you want to play music from the device or with an APP, light mustn’t be switched off from the remote controller; it should be turned off from the APP.
Remote control safety functions
Blocking protection
The remote receiver includes a function that automatically blocks motor operation, cutting current to the motor 30 seconds after detecting an obstruction in front of the fan that prevents normal operation. When this happens, you must remove the obstacles blocking the fan. Then, press the off button on the remote control to reset the receiver. Now you can continue to use the fan normally.
Note: Unless you remove the obstruction blocking the fan, it will not operate correctly.
Overload protection
If the fan’s receiver detects that the motor is operating at greater than 80W (this indicates an overload), the current to the motor will be cut automatically, which will immediately stop the fan. To reset the receiver, press the off button on the remote control. Note: If the receiver goes into protection mode again, this may indicate a motor defect. Contact the supplier immediately. The duration of the warranty is indicated in the warranty document provided in this manual.
Change in color temperature of the light.
You can change the color temperature of the light, turning off and on, with the wall switch, the remote control or in case of being an IoT fan from your terminal.
Rotation direction: summer and winter options
The sliding switch controls the direction, whether clockwise or counterclockwise.
- Summer option/down – or left-facing position (depending on the model) – The fan runs counterclockwise. The downward air current creates a refreshing effect as indicated in diagram A.
- Winter option/up – or right-facing position (depending on the model) – The fan runs clockwise. An ascending air current pushes hot air away from the fan area near the ceiling, as indicated in diagram B. This allows you to use less central heating.
Note: Turn off the fan, lower the differential, and wait for it to come to a complete stop before changing the blade rotation direction with the sliding switch.
Balancing – Wobbling problems during fan operation
If the fan body wobbles during its operation, this is not a sign of malfunctioning (even if it wobbles a few centimeters). To reduce wobbling, you can, while the fan is off:
- Check the distance between each blade and the ceiling. Measurements to the ceiling can be carried out as shown in the following diagram. If variations exist and you have already correctly tightened the screws, check that all blades have the same shape.
If any of them have a shape that is visibly different, this may be causing an imbalance during fan operation. If you have completed the previous steps and the wobbling has not resolved, you should apply dynamic balancing with the kit provided, as explained below:
- Turn the fan on to the highest speed so that the greatest amount of wobbling is produced.
- Turn off the fan. Select a blade and place a magnet on it (see diagram) halfway between the fastening and the far edge of the blade.
- Turn on the fan and check whether the wobbling has improved or gotten worse. Turn it off once again and if the wobbling has not improved, place the clip on another blade. Repeat this process and determine on which blade it improves the wobbling.
- Leave the magnet on the blade that produces the best results. Select a blade and place the magnet (see figure 1) at the base just to turning area.
- Then remove the magnet an place on of the weights (see figure 2).
Troubleshooting guide
Always consult this troubleshooting guide before contacting the technical service to avoid potentially unnecessary charges. For your safety, ensure that the fan is not connected to power before attempting the solutions suggested in this troubleshooting guide.
| Symptom | Probable causes | Solution |
| 1. The fan does not work (Important notice: The device must be disconnected from the power supply and the assistance of a certified electrician may be necessary. | A. The fuse is blown or the switch is “open”, disconnecting the power supply to the device | Check the fuses and switches on the device installation power circuit |
| B. System wiring connections are not adequately tightened | Check that wiring connections have been done correctly. They must be carried out by a certified electrician. | |
| C. The remote control is unresponsive | Replace the remote control battery if necessary. Otherwise, resynchronize the transmitter and receiver. | |
| D. No power supply | Check that the system has power and that it reaches the device. | |
| 2. Fan wobbling (follow the instructions in the “Wobbling” section of this manual) | A. The fan blades are not parallel to the ceiling | Follow the instructions indicated in the “Balancing” section of this manual. |
| B. Blade fastening screws are loose | Follow the instructions indicated in the “Balancing” section of this manual. | |
| C. Deformed blades | Follow the instructions indicated in the “Balancing” section of this manual. | |
| 3. Excessive noise when the fan moves | A. Upper canopy is touching the ceiling | Lower the upper canopy, ensuring a separation from the ceiling of no less than 3 mm. |
| B. Blade fastening screws are loose | Tighten all fastening screws once again (but not excessively) | |
| C. Ceiling mounting is loose | Retighten all ceiling mount screws | |
| D. Incorrect remote control | Replace the remote control with that provided with the device. This must be supervised by a certified electrician. Contact the distributor | |
| 4. Mechanical noise | A. If this is the first use, leave the fan on for at least 8 hours. In the event that mechanical noise continues after this period, contact the technical service | |
| 5. The lights does not turn on | A. The light is defective | Replace the light |
| 6. The fan turns but the air- flow is inadequate | A. Incorrect blade rotation direction | The blades may be rotating in the opposite direction. Follow the directions in the “Rotation Direction” section of this manual. |
| B. Inadequate distance between the ceiling and blades | Installing a fan without a shaft, flush with the ceiling, can reduce airflow. | |
| C. Existence of nearby objects | There may exist objects in the room that block airflow. | |
| D. Inadequate blade diameter | The fan chosen may be too small for the volume of the room where it is installed | |
Maintenance and information of warranty
Maintenance and cleaning:
- The fan‘s natural movement can cause certain connections to loosen. Check mounting connections, fastening parts, and blade accessories twice a year. Check that they are well fastened.
- Clean the fan periodically to help maintain its new appearance. Do not use water to clean it, as this may damage the motor or the wood, or could cause electrical shock.
- Use only a soft brush or microfiber cloth as to not scratch the finish. The veneer is sealed with a layer of lacquer to minimize discoloration or loss of shine.
- It is not necessary to oil the fan. The motor contains bearings with permanent lubrication.
Note: Failure to comply with these instructions results in the loss of the equipment warranty.
Warranty service:
The manufacturer’s warranty covers real failures that may occur but not minor complaints such as the noise generated by the device, as all electric motors generate a certain amount of noise.
Operating the fan with slightly loose components (screws not adequately tightened) or the deformation of blades due to excessively vigorous cleaning may cause excessive noise and wobbling, which will not be covered by the warranty. Taking regular care to retighten elements and clean carefully is enough to prevent these problems.
Control:
The device’s warranty will be invalid if it is installed for use with a solid-state wall switch or dimmer. It must only be used with the remote control provided with the unit.
Installing the fan:
According to the terms and conditions of our warranty, this fan can only be installed by a certified electrician. Fans that are installed incorrectly can be dangerous to people and very expensive to repair, and will lose their warranty. This fan is designed for interior use only, excluding moist areas and bathrooms. The supplier does not assume any liability for physical or bodily damage caused by the incorrect use or installation of the fan. If you are unsure, consult an electrician.
Wobbling:
All ceiling fans tend to wobble during their operation. A wobble of 2 cm is perfectly acceptable and does not indicate any malfunction nor will it cause the fan to fall, as long as it was mounted to the ceiling correctly following the instructions in this manual. This ceiling fan has a completely secure mounting system that uses steel brackets and connecting spheres to allow it to rotate and to prevent the transmission of vibrations to the ceiling structure. Please note that even fans of the same model can have different wobbles, which is totally acceptable and does not imply any malfunction or manufacturing defect.
Increased perception of noise during night time operation:
The manufacturer’s warranty does not cover the fact that during the night, when the surrounding environment is quieter, the fan’s operating noise is more apparent. In addition, during the night, the power supply may experience alterations that may produce increased noise generated by the device, which does not indicate any malfunctioning or manufacturing defect in the device.
Fan lighting system:
Noises and vibrations can be greater when the lighting system is turned on. For example, the light diffuser can produce a slight buzz if not adequately attached. Once again, non-aggressive care and regular check to ensure that all elements are properly fastened will prevent these disturbances. Glass light diffusers are covered by the warranty to the distributor ware-houses, and are subject to verification during delivery.
Warranty:
Manufactures guarantees the proper functioning of this equipment, repairs or spare parts of the model owing to faulty manufacture during 2 years after the surrender date,8 years exclusively in the case of the fan motor. Responsibility will not be accepted, however, for damages or injury caused through misuse. For any claims the sale ticket must be presented. The company agrees to repair any defect or malfunction found in the item and any damages said defect or malfunction might directly cause. If the reparation should fail to satisfy the customer and/or the object fail to present the optimum condition for the use to which it is destined the guarantee holder will have the right to the substitution of the acquired item for another identical in characteristics or a complete refund of the purchase price. Terms and conditions of warranty www.sulion.es
Installing the ceiling fan
DECLARATION OF CONFORMITY
| RED 2014/53/EU |
| Article 3.1a |
| EN 60598-1:2015 + A1:2018 |
| EN 60598-2-1:1989 |
| EN 60335-1:2012 + A11:2014 + A13:2017 |
| EN 60335-2-80:2003 + A1:2004 + A2:2009 |
| EN 62233:2008 |
| EN 62471:2008 |
| EN 62493:2010 |
| Article 3.1b |
| EN 55014-1:2006 + A1:2009 + A2:2011 |
| EN 55014-2:1997 + A1:2001 + A2:2008 |
| EN 55015:2013 |
| EN 61000-3-2:2014 |
| EN 61000-3-3:2013 |
| EN 61547:2009 |
| EN 301 489-1 V2.1.1 |
| EN 301 489-17 V3.1.1 |
| Article 3.2 |
| EN 300 328 V2.1.1 |
| RoHS 2015/863/EU |
| ERP 2009/125/EC |
| 1194/2012 |
| 2015/1428 |
Documents / Resources
 |
Sulion 075696 Ceiling Fan with Built-in LED Light [pdf] Installation Guide 075696 Ceiling Fan with Built-in LED Light, 075696, Ceiling Fan with Built-in LED Light, with Built-in LED Light, LED Light |