O B E C2D Smart Projector User Manual

O-B-E-LOGO

O B E C2D Smart Projector

O-B-E-C2D-Smart-Projector-PRODUCT

Important Safety Instructions

  1. Do not look directly into the projection lens during use. Strong light entering the eyes may damage your vision!
  2. Do not block the projection lens while the product is in operation.
  3. The product has ventilation and heat dissipation holes around or at the bottom. Do not block these vents; otherwise, it may cause overheating or damage to the product.
  4. Do not place the product near liquids (e.g., water, seawater), heat sources (e.g., fire, heaters), or other hazardous environments to avoid risks.
  5. Do not expose batteries to extreme high temperatures or high altitudes. Do not throw battery packs into fire or heating furnaces, disassemble, strike, crush, cut, short-circuit, or touch batteries with sharp objects. This may cause fire, explosion, or other hazards!
  6. Check the battery polarity carefully. Do not use different types of batteries together, or replace them with incorrect model battery packs. This may lead to fire, explosion, or other hazards!
  7. Keep batteries out of reach of children to prevent accidental ingestion. If a child swallows a battery, seek medical help immediately.
  8. Do not dispose of batteries in household garbage. Follow national regulations for safe disposal of used batteries.
  9. If the product will not be used for an extended period, disconnect the external power supply.
  10. Do not disassemble the product or touch internal components under any circumstances.
  11. For all internal maintenance of the device, contact our customer service center.

Packaging Overview

O-B-E-C2D-Smart-Projector- (1)

Connectivity

  • DC: Connect your projector to the power source with the included power cable.
  • USB2.0: Connect a USB2.0 device to access photos, music, and movies.
  • HDMI: Connect cable box, Blu-ray player, gaming console, or other devices to your projector using HDMI cables.
  • AUDIO: Connect 3.5mm headphone jack connects headphones or external audio devices to output the projector’s audio.
  • POWER: Power on/off

Gimbal Bracket Installation Instructions

  • Tighten the cantilever screw clockwise to align the screw hole of the chassis with the cantilever screw hole.
  • Align the screws and tighten the screws clockwise to align the threaded holes on the bottom of the projector with the threaded holes on the swing arm.

O-B-E-C2D-Smart-Projector- (2)Important Notes: When installing on the wall or ceiling, please find a professional to install it to ensure stability and safety.

Remote Control

O-B-E-C2D-Smart-Projector- (3) O-B-E-C2D-Smart-Projector- (4)

Remote Pairing

Please keep the remote within 10 cm of the device Hold O-B-E-C2D-Smart-Projector- (6)  simultaneously until the remote control light flashes quickly to enter pairing mode

O-B-E-C2D-Smart-Projector- (5)

Keystones & Focus
There are three ways to enable Autofocus on OBE Smart Projector:

  1. Turn on Autofocus by going to Settings > Focus > Auto Focus.
  2. Gently move the projector to trigger the autofocus mechanism.
  3. Press and hold the AF button on the remote to trigger autofocus.

Activate manual keystone with the following steps:
Go to Settings > Projector > Image Correction > Manual Keystone Correction.

O-B-E-C2D-Smart-Projector- (7)

Bluetooth Speaker Mode

Your projector can also be used as a speaker.

  1. Settings > Bluetooth & Accessories > My Devices.
  2. Select Home, then All apps > Bluetooth Music.

When entering Bluetooth speaker mode, you can press the power button on the remote control to select Screen OFF to turn off the screen display.

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

For projector:
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons. For remote control: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For the receiver devices associated with the operation of a licensed radio service, they bear the following statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

FCC D : 2BRQF-C2D

WARNING: Cancer and Reproduction Harm  www.P65Warmings.ca.gov.

If you have any questions, please contact us by email. We will solve any problems you encounter within 24 hours.

Documents / Resources

PDF thumbnailC2D Smart Projector
User Manual · 2BRQF-C2D, 2BRQFC2D, C2D Smart Projector, C2D, Smart Projector, Smart Projector, Smart, Projector

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Telefonu projeksiyona nasıl yansitirim

    🇹🇷 Emrah Evsen asks Telefonu projeksiyona nasıl yansitirim
    Manuals+ clarified question
    Question

    How do I mirror my phone to the O B E C2D Smart Projector?

    Answer

    While the provided manual for the O B E C2D Smart Projector does not explicitly detail a specific "Screen Mirroring" app name, smart projectors of this type typically support mirroring through built-in software. Please try the following steps:

    • Check for Pre-installed Apps: Navigate to the All Apps or Shortcut Key menu on your home screen. Look for apps named Eshare, AirPlay, Miracast, or Screen Mirroring.
    • Network Connection: Ensure both your phone and the projector are connected to the same Wi-Fi network.
    • Android Users: Open the mirroring app on the projector (often Miracast), then select "Screen Cast" or "Smart View" from your phone's quick settings menu.
    • iOS Users: Open the AirPlay-compatible app on the projector, then open "Screen Mirroring" from your iPhone's Control Center.

    If you cannot find a dedicated app, you can also connect your phone using an HDMI adapter plugged into the HDMI port on the back of the projector.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.