strands Freedom Legacy Reverse Light Rectangular
Overview
This reverse light is installed with a loose 245 cm cable and connected using the provided wiring instructions. Follow local mounting laws, install with power turned off, and protect the breather during care and installation.
Specifications
| Part No. | 800266 |
|---|---|
| Product name | Freedom Legacy Reverse Light (Rectangular) |
| Type of connection/cable length | 245 cm loose cable |
| Wire size | 0.75 mm² |
| Included in package | Bracket |
| Wiring | Black: + Positive; White: – Negative |
How To Use
- Read all instructions and study the diagram(s) before installing.
- Ensure power is turned off during installation.
- Do not cut the connector cable to less than 50 cm. If it is already shorter than 50 cm, leave it as is.
- Use only the correct accessories included in the package.
- Connect wires: Black to + (positive) and White to – (negative).
- Use a watertight solution for wiring connections.
- Tighten screws, washers, and nuts to prevent loosening or chafing; avoid overtightening.
- After switching off, do not remove or touch the casing for at least 30 minutes (the light can become hot under continuous use).
Please check state and local laws for proper usage and mounting. Strands will not be responsible for products mounted incorrectly or in violation of local laws (e.g., ECE R48 regulation for the EU)
Dimenstion
CARE
- Clean the product with lukewarm water and an alkaline degreaser. Avoid strong chemicals; rinse immediately if exposed. Do not use a pressure washer for cleaning.
- Take care if your light has a breather. Ensure it is protected against rain and dust, especially if it has a sticker breather. Damage to the breather due to incorrect installation will void the warranty.
- Internal moisture is normal and will dissipate through the breather vent after several days of use.
- We do not recommend painting the product housing. If paint is still applied, please ensure the breather is protected, and an oven is not used for curing the paint. Otherwise, the warranty might be void.
INSTALLATION
- Ensure power is turned off during installation.
- Do not cut the connector cable to less than 50 cm. If the original cable is already shorter than 50 cm, leave it as is. Otherwise, the warranty will be void.
- Make sure to use only the correct accessories included in the package. Installation errors may void the warranty.
- Tighten screws, washers, and nuts to prevent them from loosening or chafing. Do not overtighten screws to avoid damaging the product’s protective components.
- Use a watertight solution for wiring connections.
WARNING: For safe operation, use only the voltage specified in the product description. This light becomes hot under continuous use. Do not remove or touch the casing for at least 30 minutes after turning the lamp off
Troubleshooting
- Breather-related issues/warranty risk: If the light has a breather, ensure it is protected against rain and dust, especially if it has a sticker breather. Damage to the breather due to incorrect installation may void the warranty.
- Internal moisture concern: Internal moisture is normal. It will dissipate through the breather vent after several days of use.
- Cleaning problems or surface damage: Clean with lukewarm water and an alkaline degreaser. Avoid strong chemicals and rinse immediately if exposed. Do not use a pressure washer. If paint is applied, protect the breather and do not use an oven for curing paint; otherwise, the warranty might be void.
- Incorrect operation/safety: For safe operation, use only the voltage specified in the product description. If unsure, contact support for assistance
Documents / Resources
 | Freedom Legacy Reverse Light Rectangular |
References
- strandseurope.com/sv/about-us/function-warrantystrandseurope.com
- strands.sewww.strands.se
- strands.se/www.strands.se
- strandseurope.comwww.strandseurope.com
- strandseurope.com/www.strandseurope.com
- User Manualmanual.tools
Published: July 18, 2026