steady STS-SENSOR Programmable Universal TPMS Sensor
Specifications
- Product Name: TMPS Sensor
- Model: TMPS-100
- Compatibility: Universal
- Power Source: 3V Lithium Battery
- Operating Temperature: -20°C to 80°C
- Transmission Range: 30ft
Product Usage Instructions
Installation:
- Locate the valve stem of the tire.
- Remove the valve cap and valve core carefully.
- Thread the TMPS sensor onto the valve stem and tighten it securely.
- Replace the valve core and valve cap.
Pairing with Display Unit:
- Refer to the display unit’s user manual for pairing instructions.
- Ensure the TMPS sensor is within the transmission range of the display unit.
- Follow the pairing process on the display unit to connect with the TMPS sensor.
Maintenance
Check the battery status regularly and replace it with a new 3V lithium battery when needed. Inspect the sensor for any damage or corrosion.
SENSOR VIEW
SENSOR SPECIFICATION
WARNING
- Please read the warnings and review the instructions before installation.
- Professional installation only. Failure to follow the installation guide may prevent the TPMS sensor from operating properly.
CAUTION
- The sensor installation should be carried out by
- The sensor is replacement or maintenance parts for the vehicles that have a factory-installed TPMS only.
- Make sure to program the sensor by programming tools for the specific vehicle make, model, and year before the installation.
- Do not install the sensor on damaged wheels.
- Pictures in the manual are just for illustration.
- The content and specifications are subject to change without prior notice.
STEPS
- Unload from the vehicle and deflate the tire. Remove the original sensor.
- Line the sensor up witha rim hole. Pull the valve stem straight through the valve hole and adjust the installation position.
- Screw the sensor into the top of the stem. Use a wrench tohold the valve stem and maintain a vertical position, then tighten the screw with 1.2Nm torque.
- Mount the tire over the rim.
- TMPS SENSOR
- Add: 1310 René-Lévesque, Suite 902,
- Montreal, QC, H3G 0B8 Canada
Website: www.steadytiresupply.ca
FC FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,undero Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedbyh the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum 20cm distance between the radiator and your body:
Use only the supplied antenna.
Frequently Asked Questions
- Q: How often should I replace the battery in the TMPS sensor?
A: It is recommended to replace the battery every 1-2 years or when the low battery indicator is displayed on the monitor. - Q: Can I use the TMPS sensor in extreme temperatures?
A: The TMPS sensor is designed to operate within a temperature range of -20°C to 80°C, ensuring reliable performance in various conditions.
Documents / Resources
 | steady STS-SENSOR Programmable Universal TPMS Sensor [pdf] User Manual 2BGNNSENSOR, STS-3-FCC, STS-SENSOR Programmable Universal TPMS Sensor, STS-SENSOR, Programmable Universal TPMS Sensor, Universal TPMS Sensor, TPMS Sensor, Sensor |