10A DSP Series Topp Pro Professional Audio Gear
Dongguan Jingheng Electron Co., Ltd. Room 101, Building 1, No.15, Shenle 1st Road, Hengli Town, Dongguan City, 523465 Guangdong, P.R. China
STARK DSP
STARK 8A DSP / 10A DSP / 12A DSP / 15A DSP
2
1. Introduction
4
2. Features
4
3. Useful Data
4
4. Back Panel Description
5
5. Connection Plate
6
6. BT Control
8
7. Wire Connections
10
8. Technical Specifications
11
9. Guarantee
13
3
– Output Power: 600W Continuous(300LF+300HF) / 1200W Program / 2400W Peak Power, Class D. – Connections: 1 x XLR/F ¼” Combo(Mic/Line) Input, 1 x 3.5 Stereo AUX IN, 1 x Stereo BT(app control),
1 x XLR/M(CH1 Link/Mix out) Output. – DSP Preset Modes: LIVE-MUSIC-SPEECH-DJ. – Electronic Protections: Electronic Clip,Thermal and Transducer Overdrive Protection. – Enclosure Construction: MDF Cabinet,Resistant Black Paint, Rubber Feet, Metal Grille with Foam,
One handles. – Mounting information: One Metal Standard Pole-Mount(36mm). – Power Supply: 110-120V~60Hz / 220-240V ~50/60Hz Switch Mode.
4
7 6
13
5
12
4
11
3
10
8
9
2
1. Bi-Polar Main Power Switch.
1
2. AC Power Socket with Main Fuse.
3. Line/Mic Input ON Combo Connector.
4. “Input Sensitivity”Switch for Line/MIC.
5. CH1 Volume Control.
6. BT/AUX Volume Control.
7. BT TWS Connection button; (Double Clicks for TWS Connection).
8. BT Pair Connection button; (One Click it to Pair Music Source).
9. AUX In.
10. Mix Out.
11. Selection Switch for 4 DSP Presets, select your Favoutite Among live-music-speech-DJ
– LIVE-for live sound reinforcement applications(Defaults).
– MUSIC-for recording music playback and EDM applications.
– SPEECH-for vocal language applications.
– DJ-for dynamic music reinforcement applications.
12. Power, Green Led, indicate on Status.
13. Signal/Limit, Red Led, indicate on Status.
5
For Active Full Range Speaker System 1). Connect one side of the signal cable at your mixer into the Output Left / Right (with Stereo Jack or XLR)
and the other side of the cable into the Line Input (COMBO) of your active speaker cabinet (with Stereo Jack or XLR). 2). Connect the power cord to main. 3). Turn ON your mixer first, then the active speaker cabinets. 4). Turn up the volume control of the cabinets. 5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to reach the desired output level. 6). After use, turn off your active speaker cabinets first, then the mixer.
6
Two Active Subwoofers & Two Active Satellite Speakers 1). Connect one side of the signal cable at your mixer into the Output Left / Right and the other side of
the cable into the Line Input of your active subwoofers. 2). Connect one side of another signal cable at your active subwoofers into Link Left / Right or Out Left /
Right, and the other side of the cable into the Line Input Left / Right of your active satellite speakers. * If you connect into Out Left / Right and press Bypass switch, the 80Hz HPF will be activated. 3). Connect the power cord to main. 4). Turn ON your mixer first, then the active speaker cabinets. 5). Turn up the volume control of the active speaker cabinets. 6). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to reach the desired output level. 7). After use, turn off your active speaker cabinets first, then the mixer.
7
BT Control
BT PAIR: Paired to one speaker 1). One click the”PAIR”button on the master speaker,You will hear a beep (boom), then the blue starts to flash. which means to enter pairing state. 2). Turn on the Bluetooth function on the audio device, search and select “STARK DSP” to start pairing; (iPhone, iPad, Bluetooth adapter and other audio devices, no pairing password is required). 3). After about 20-100 seconds, the pairing will be completed. Once paired sucessfuly between source device and product, the blue will solid light, if pair failed, Please repeat above steps 1-3 to try pairing again. 4). Music playback *Bluetooth memory function: After the unit reboot, the system will proceed the automatic pairing based on the last memory.
BT TWS: Interconnection between two of the same speakers Remark: If the speaker connected to your source device is the master, The other speaker linked with it will the Slave. The sound signal will be sent to the master from source device, if the master speaker linked with the Slave speaker. then it playback on the left channel of the master and on the right channel of the Slave, Finally realize the left/right channel stereo effects. 1). Select one of two linked speaker as the master. 2). One click the PAIR button on the master, You will hear a beep (boom), then the blue starts to flash, which means to enter pairing state. 3). Open the BT function on audio device, Then search and select “STARK DSP” to start pairing (iPhone, iPad, Bluetooth adapter and other audio devices, no pairing password is required). 4).After about 20-100 seconds, the pairing will be completed. Once paired sucessfuly between source device and product, the blue will solid light, if pair failed, Please repeat above steps 1-3 to try pairing again. 5). Separately Double clicks the LINK button on the master and the Slave, you will keep hear a beep (boom) and keep 20-100 seconds. 6). Once the master paired to the Slave sucessfully, the beep(boom) will disappear and the BT indicatior will light solid blue. 7). Play music.
The Master Speaker (left channel)
Stereo Music Signal
The Slave speaker (right channel)
Bluetooth Audio Device (iPhone/iPad/BT adaptor ,etc.)
8
BT Control
BT CONTROL APP: 1. Please download the “Sound Control DSP” APP from the APP store.
There are IOS and Android versions for selection. 2. Turn on the power switch of the STARK SERIES product 3. Turn on the Bluetooth device on your phone or iPad, and then open the “Sound Control” APP 4. Click Refresh, click the selected model in the product model list that appears, and then click “Connect” to enter the control interface, as shown in the figure below
Connection Introduction:
Function Introduction:
Save or load Adjusted Presets
Main Interface
EQ
HPF X-OVER Option
LOCATION Option
DSP MODE Option
9
10
Model Active System Type Output Power Maximun SPL Transducer Low Transducer High Frequency Response Frequency Range Horn Coverage ( HxV ) Connectors
External Controls Indicators DSP Preset Modes Electronic Protections Enclosure Construction Mounting information Power Supply Dimension(H*W*D) Net Weight
STARK 8A DSP 2-WAY 8”Active Vented Loudspeaker System 600W Continuous(300LF+300HF) / 1200W Program / 2400W Peak Power, Class D 123dB(@1m) 120dB Continuous(dB spl@1m) 8″ -2″Voice Coil, Ferrite 1″Ferrite Driver-1″Voice Coil 65Hz – 20kHz(-3dB) 55Hz – 20kHz(-10dB) 90° x 60° 1 x XLR/F ¼” Combo(Mic/Line) Input 1 x 3.5 Stereo AUX IN, 1 x Stereo BT(app control) 1 x XLR/M(CH1 Link/Mix out) Output Volume Control / BT Pair and Link Switch / DSP Preset Switch / AC Power Switch Signal/Clip Limiter LED, Four DSP Output Mode LEDs, BT Pair-Link LED, Power Switch LED LIVE-MUSIC-SPEECH-DJ Electronic Clip,Thermal and Transducer Overdrive Protection MDF Cabinet, Resistant Black Paint, Rubber Feet, Metal Grille with Foam, One handles One Metal Standard Pole-Mount(36mm) 110-120V~60Hz / 220-240V ~50/60Hz Switch Mode 482*281*290mm(18.9″*11.1″*11.4″) 13.5Kg / 29.4 Ibs
Model Active System Type Output Power Maximun SPL Transducer Low Transducer High Frequency Response Frequency Range Horn Coverage ( HxV ) Connectors
External Controls Indicators DSP Preset Modes Electronic Protections Enclosure Construction Mounting information Power Supply Dimension(H*W*D) Net Weight
STARK 10A DSP 2-WAY 10”Active Vented Loudspeaker System 600W Continuous(300LF+300HF) / 1200W Program / 2400W Peak Power, Class D 125dB(@1m) 122dB Continuous(dB spl@1m) 10″ -2″Voice Coil, Ferrite 1″Ferrite Driver-1″Voice Coil 60Hz – 20kHz(-3dB) 50Hz – 20kHz(-10dB) 90° x 60° 1 x XLR/F ¼” Combo(Mic/Line) Input 1 x 3.5 Stereo AUX IN, 1 x Stereo BT(app control) 1 x XLR/M(CH1 Link/Mix out) Output Volume Control / BT Pair and Link Switch / DSP Preset Switch / AC Power Switch Signal/Clip Limiter LED, Four DSP Output Mode LEDs, BT Pair-Link LED, Power Switch LED LIVE-MUSIC-SPEECH-DJ Electronic Clip,Thermal and Transducer Overdrive Protection MDF Cabinet, Resistant Black Paint, Rubber Feet, Metal Grille with Foam, One handles One Metal Standard Pole-Mount(36mm) 110-120V~60Hz / 220-240V ~50/60Hz Switch Mode 560*324*320mm(22.0″*12.8″*12.6″) 16.8Kg / 36.8 Ibs
11
Model Active System Type Output Power Maximun SPL Transducer Low Transducer High Frequency Response Frequency Range Horn Coverage ( HxV ) Connectors
External Controls Indicators DSP Preset Modes Electronic Protections Enclosure Construction Mounting information Power Supply Dimension(H*W*D) Net Weight
STARK 12A DSP 2-WAY 12”Active Vented Loudspeaker System 600W Continuous(300LF+300HF) / 1200W Program / 2400W Peak Power, Class D 127dB(@1m) 124dB Continuous(dB spl@1m) 12″ -2″Voice Coil, Ferrite 1″Ferrite Driver-1″Voice Coil 55Hz – 20kHz(-3dB) 46Hz – 20kHz(-10dB) 90° x 60° 1 x XLR/F ¼” Combo(Mic/Line) Input 1 x 3.5 Stereo AUX IN, 1 x Stereo BT(app control) 1 x XLR/M(CH1 Link/Mix out) Output Volume Control / BT Pair and Link Switch / DSP Preset Switch / AC Power Switch Signal/Clip Limiter LED, Four DSP Output Mode LEDs, BT Pair-Link LED, Power Switch LED LIVE-MUSIC-SPEECH-DJ Electronic Clip,Thermal and Transducer Overdrive Protection MDF Cabinet, Resistant Black Paint, Rubber Feet, Metal Grille with Foam, One handles One Metal Standard Pole-Mount(36mm) 110-120V~60Hz / 220-240V ~50/60Hz Switch Mode 583*352*360mm(22.9″*13.9″*14.2″) 19.2Kg / 42.3 Ibs
Model Active System Type Output Power Maximun SPL Transducer Low Transducer High Frequency Response Frequency Range Horn Coverage ( HxV ) Connectors
External Controls Indicators DSP Preset Modes Electronic Protections Enclosure Construction Mounting information Power Supply Dimension(H*W*D) Net Weight
STARK 15A DSP 2-WAY 15”Active Vented Loudspeaker System 600W Continuous(300LF+300HF) / 1200W Program / 2400W Peak Power, Class D 129dB(@1m) 126dB Continuous(dB spl@1m) 15″ -2″Voice Coil, Ferrite 1″Ferrite Driver-1″Voice Coil 50Hz – 20kHz(-3dB) 43Hz – 20kHz(-10dB) 90° x 60° 1 x XLR/F ¼” Combo(Mic/Line) Input 1 x 3.5 Stereo AUX IN, 1 x Stereo BT(app control) 1 x XLR/M(CH1 Link/Mix out) Output Volume Control / BT Pair and Link Switch / DSP Preset Switch / AC Power Switch Signal/Clip Limiter LED, Four DSP Output Mode LEDs, BT Pair-Link LED, Power Switch LED LIVE-MUSIC-SPEECH-DJ Electronic Clip,Thermal and Transducer Overdrive Protection MDF Cabinet, Resistant Black Paint, Rubber Feet, Metal Grille with Foam, One handles One Metal Standard Pole-Mount(36mm) 110-120V~60Hz / 220-240V ~50/60Hz Switch Mode 665*420*400mm(26.2″*16.5″*15.7″) 22.8Kg / 50.3 Ibs
12
9
13
10 Notes
14
Notes
10
15
/
: 12
TOPP PRO NF05940 – STARK DSP TOPP PRO_V1.2 STARK 15A DSP 0.1KG / 1 NH00149 12 A3 A4 A5 :
6 pcs
20231225
: mm :± 3mm
210 mm 297 mm
420 mm
1.2
20231226
QHFBE004-20231200013
Documents / Resources
 |
STARK DSP 10A DSP Series Topp Pro Professional Audio Gear [pdf] User Manual 10A DSP Series Topp Pro Professional Audio Gear, 10A DSP Series, Topp Pro Professional Audio Gear, Professional Audio Gear, Audio Gear, Gear |
