STMicroelectronics UM2406 The RF-Flasher Utility Software Package Manual

Tlhophiso ea Sephutheloana sa Software:
Ho sebelisa sesebelisoa, tobetsa letšoao la tšebeliso ea RF-Flasher le fumanehang ho [Qala] > [ST RF-Flasher Utility xxx] > [RFFlasher Utility].

Toolbar Interface
Karolong ea lithulusi tsa fensetere ea mantlha ea RF-Flasher, basebelisi ba ka etsa lits'ebetso tse latelang:

Kenya .bin e teng kapa .hex file: [File] > [Bula file…]

Boloka setšoantšo sa hona joale sa memori: [File] > [Boloka File Joalo ka…]
Koala .bin e teng kapa .hex file: [File] > [Koala file]

Beha makhetlo a ST-LINK: [Lisebelisoa] > [Litlhophiso...]
Lumella kapa thibela log file popo: [Lisebelisoa] > [Litlhophiso…]

LBH

Ke lisebelisoa life tse tšehetsoeng ke RF-Flasher utility software package?
Sephutheloana sa software hajoale se tšehetsa lisebelisoa tsa BlueNRG-LP, BlueNRG-LPS, BlueNRG-1, le BlueNRG-2.

Ke litlhokahalo life tse tlase tsa sistimi ho tsamaisa ts'ebeliso ea RF-Flasher?
Litlhokahalo tse tlase tsa sistimi li kenyelletsa bonyane 2 GB ea RAM, likou tsa USB, le Adobe Acrobat Reader 6.0 kapa hamorao.
Nka boloka setšoantšo sa memori ea hajoale joang ts'ebelisong ea RF-Flasher?
Ho boloka setšoantšo sa memori ea hajoale, ea ho [File] > [Boloka File E le…] ebe u khetha karolo ea memori e tla bolokoa ho .bin file.

UM2406
Bukana ea mosebelisi

Sephutheloana sa lisebelisoa tsa RF-Flasher

Selelekela

Tokomane ena e hlalosa sephutheloana sa lisebelisoa tsa lisebelisoa tsa RF-Flasher (STSW-BNRGFLASHER), se kenyeletsang RF-Flasher utility PC application.
Sesebelisoa sa RF-Flasher ke sesebelisoa sa PC se ikemetseng, se lumellang BlueNRG-1, BlueNRG-2, BlueNRG-LP, le BlueNRG-LPS Bluetooth® Low Energy system-on-chip flash memory ho baloa, ho hlakoloa ka bongata, ho ngoloa le ho hlophisoa.
Hajoale e ts'ehetsa sebopeho sa memori ea Flash ea BlueNRG-LP, BlueNRG-LPS, BlueNRG-1, le BlueNRG-2 ka mokhoa oa UART o sebelisa sesebelisoa sa kahare sa UART sa bootloader. Hape hajoale e ts'ehetsa sebopeho sa memori ea Flash ea BlueNRG-LP, BlueNRG-LPS, BlueNRG-1, le BlueNRG-2 ka mokhoa oa SWD ka ho sebelisa sebopeho se tloaelehileng sa SWD ka lisebelisoa tse tloaelehileng tsa ho hlophisa / ho lokisa (CMSIS-DAP, ST-LINK, le J-Link).
Ho feta moo, e boetse e lumella aterese ea MAC hore e bolokehe sebakeng se itseng sa memori ea flash e khethiloeng ke mosebelisi ka mekhoa ea UART le SWD.
Sephutheloana sa software sa RF-Flasher se boetse se fana ka ts'ebeliso e ikemetseng ea flasher launcher, e lumellang lenaneo la memori ea flash, ho bala, ho hlakola ka bongata, le ho netefatsa litaba. Sesebelisoa sa ho hlahisa flasher se hloka fensetere ea PC DOS feela.

Hlokomela:
Lentsoe la RF hajoale le bolela lisebelisoa tsa BlueNRG-LP, BlueNRG-LPS, BlueNRG-1, le BlueNRG-2. Liphapang leha e le life tse khethehileng li totobatsoa moo ho hlokahalang.

Lintlha tse akaretsang

Lethathamo la li-acronyms

Lethathamo la 1. Lethathamo la li-acronyms

Nako	Tlhaloso
RF	Maqhubu a seea-le-moea
SWD	serial wire debug
UART	Universal asynchronous receiver-transmitter
USB	Universal letoto la bese

Litokomane tsa litšupiso

Lethathamo la 2. Litokomane tsa litšupiso

Referense	Mofuta	Sehlooho
DS11481	Lethathamo la lintlha tsa BlueNRG-1	Programmable Bluetooth® Low Energy wireless SoC
DS12166	Lethathamo la lintlha tsa BlueNRG-2	Programmable Bluetooth® Low Energy wireless SoC
DB3557	STSW-BNRGFLASHER lintlha tse khutšoanyane	Lintlha tse khutšoane bakeng sa sephutheloana sa software sa RF-Flasher
DS13282	Lethathamo la lintlha tsa BlueNRG-LP	Programmable Bluetooth® Low Energy wireless SoC
DS13819	Lethathamo la lintlha tsa BlueNRG-LPS	Programmable Bluetooth® Low Energy wireless SoC

Rea qala

Karolo ena e hlalosa litlhoko tsohle tsa sistimi ho tsamaisa RF-Flasher utility PC application le ts'ebetso e amanang le eona ea ho kenya sephutheloana sa software.

Litlhoko tsa tsamaiso
Sesebelisoa sa RF-Flasher se na le litlhoko tse latelang tse tlase:

PC e nang le processor ea Intel® kapa AMD e sebelisang sistimi e latelang ea Microsoft®:
- Windows® 10
Bonyane 2 GB ea RAM
Likou tsa USB
Adobe Acrobat Reader 6.0 kapa hamorao
Sekhahla sa ponts'o se khothalelitsoeng le litlhophiso li fihla ho 150%.

Ho theha sephutheloana sa software
Mosebelisi a ka sebelisa sesebelisoa sena ka ho tobetsa letšoao la ts'ebeliso ea RF-Flasher ([Qala]>[ST RF-Flasher Utility xxx]>[RF-Flasher Utility]).

Sehokelo sa Toolbar

Karolong ea lithulusi tsa fensetere ea RF-Flasher, mosebelisi a ka etsa lits'ebetso tse latelang:

Kenya .bin e teng kapa .hex (Intel e atolositsoe) file, sebelisa [File]>[Bula file…]
Boloka setšoantšo sa memori sa hajoale ho .bin file, sebelisa [File]>[Boloka File Joalo ka…]. Aterese ea ho qala le boholo ba karolo ea memori e lokelang ho bolokoa ho file li ka khethoa ho tsoa tab ea Memori ea Sesebelisoa.
Koala .bin e teng kapa .hex file, sebelisa [File]>[Koala file]
Beha sekhahla sa ST-LINK, u sebelisa [Lisebelisoa]>[Litlhophiso...]
Lumella kapa thibela log file ho theha ka mokhoa oa UART/SWD, ho sebelisoa [Lisebelisoa]> [Litlhophiso…]. Haeba log files li bolokiloe, hoa khoneha ho beha boemo ba tlhahisoleseding ea debug ho boloka (bakeng sa SWD feela). Tsohle log files li bolokiloe ho {insta llation path}\ST\RF-Flasher Utility xxx\Logs\.
Hlakola ka bongata, ho sebelisoa [Lisebelisoa]>[Hlakola ka bongata].

Netefatsa litaba tsa memori ea flash [Lisebelisoa]> [Netefatsa litaba tsa flash].
Fumana mofuta oa ts'ebeliso, u sebelisa [Thuso]>[Mabapi].
Khoasolla a file, sebelisa [Lisebelisoa]>[Flash].

Hlakola likarolo tsa lisebelisoa, u sebelisa [Lisebelisoa]>[Hlakola Maqephe…]
Bapisa memori ea sesebelisoa le setšoantšo se khethiloeng file, ho sebelisa [Lisebelisoa]>[Bapisa Memori ea Sesebelisoa le file]. Litšoantšo tse peli files li hlahisoa ho Bapisa Memori ea Sesebelisoa le Setšoantšo File tab le diphapano tse amanang di totobatswa ka bofubedu.
Bapisa tse peli files, sebelisa [File]>[Bapisa tse peli files]

Bala karolo ea bootloader (feela ka mokhoa oa SWD), u sebelisa [Lisebelisoa]>[Read Bootloader Sector (SWD)].
Bala sebaka sa OTP (feela ka mokhoa oa SWD), u sebelisa [Lisebelisoa]>[Bala Sebaka sa OTP (SWD)].
Boloka likarolo tsa bootloader kapa sebaka sa OTP ka har'a .bin file, sebelisa [File]>[Boloka File Joalo ka…].

Mosebelisi a ka khetha litšoantšo tse peli files le bapise tsona. Litšoantšo tse peli files li hlahisoa ho Bapisa tse peli Files tab le diphapano tse amanang di totobaditswe ka bofubedu. .bin le .hex file lifomate li tšehetsoa.

Karolong e kaholimo ea fensetere ea mantlha ea lisebelisoa tsa RF-Flasher, mosebelisi a ka khetha setšoantšo file ka [Khetha Setšoantšo File] konopo. Mosebelisi a ka khetha mofuta oa memori: memori ea flash, bootloader, kapa sebaka sa OTP. Bakeng sa sebaka sa memori ea flash, mosebelisi a ka beha aterese ea ho qala (feela bakeng sa bin file)
Likhetho tsena kaofela li fumaneha ka mokhoa oa UART le SWD.
Mosebelisi o hloka ho nolofalletsa ho fihlella mokhoa o khethiloeng (UART kapa SWD). Ba ka etsa sena ka ho bula sekepe sa COM se amanang le mokhoa oa UART, kapa ka ho hokahanya sesebelisoa sa SWD hardware programming/debugging ho lisebelisoa tsa SWD lines.

UART fensetere e kholo
Ka fensetere e ka sehloohong ea UART ea fensetere e ka sehloohong ea lisebelisoa tsa RF-Flasher, mosebedisi a ka khetha sekepe sa COM se tla sebelisoa ho hokahanya sesebelisoa ka Lethathamo la karolo ea COM Ports.
Sekhahla sa serial baud se sebelisoang bakeng sa boto ea tlhahlobo ea lisebelisoa tsa RF ke 460800 bps.

Mokhoa oa UART: mokhoa oa ho matha
Setšoantšo file khetho
Ho kenya .bin e teng kapa .hex file, sebelisa [Khetha Setšoantšo File] konopo leqepheng la sehlooho, ea ho [File]>[Bula File…], kapa u ee ho Setšoantšo File tab ya. Tsela e feletseng ea ba khethiloeng file e hlaha haufi le konopo 'me konopo ea [Flash] e sebetsa ha e file e laisitse.
Lethathamo la COM Ports tab e bonts'a lisebelisoa tsohle tse hokahantsoeng likoung tsa USB tsa PC. Likonopo tsa [Khetha Tsohle], [U se Khetha Tsohle], le [Fetola Tsohle] li lumella mosebelisi ho hlalosa hore na ke lisebelisoa life tse hoketsoeng (tsohle, ha ho le e 'ngoe, kapa tse ling tsa tsona) tse lokelang ho ba sepheo sa ts'ebetso ea ts'ebeliso. Ka tsela ena, ts'ebetso e tšoanang (ke hore, flash memory programming) e ka etsoa ka nako e le 'ngoe ho lisebelisoa tse ngata. Konopo ea [Refresh] e lumella mosebelisi ho nchafatsa lethathamo la lisebelisoa tse hoketsoeng.
Ka tloaelo, khetho ea [Miss erase] karolong ea [Liketso] ha e hlahlojoe, 'me ke maqephe a memori a hlokahalang feela a hlakotsoeng le ho ngoloa ka file dikahare. Ha khetho ena e hlahlojoa, ho hlakola ka bongata ho tla etella pele mohato oa lenaneo la memori ea flash.
Khetho ea [Verify] e qobella cheke ho netefatsa hore litaba tsa memori li ngotsoe ka nepo.
Sheba khetho ea [Apdate Device Memory] ho nchafatsa tafole ea memori ea sesebelisoa kamora ts'ebetso ea memori ea flash.
Khetho ea ts'ireletso ea ho bala e thusa ts'ireletso ea ho bala ha sesebelisoa ka mor'a lenaneo la memori ea flash.
Sheba khetho ea [Auto Baudrate] ha feela ho seta hardware ho etsoa botong ho qobella ts'ebetso ea [Auto Baudrate]. Ka kamehla, khetho ea [Auto Baudrate] ha e hlahlojoe.

Setšoantšo File tab ya
E khethiloeng file lebitso, boholo, le likahare tse arotsoeng tse lokelang ho hlophisoa memori ea sesebediswa e ka ba viewed ho Setšoantšo File tab ya.

Thebo ea Memori ea Sesebelisoa
Khetha tab ena ho ea view dikahare tsa memori tsa sesebelisoa se hoketsoeng (ka konopo ea [Bala]) le log e nang le lits'ebetso tse entsoeng sesebelisoa se khethiloeng.

Tobetsa konopo ea [Bala] ho fetisetsa karolo ea memori e hlalositsoeng ke [Aterese ea ho Qala le Boholo] tafoleng.
Ho bala memori eohle ea flash, sheba khetho ea [Memori Eohle].
Kholomo ea pele e fana ka aterese ea mantlha ea li-byte tse 16 tse latelang ka tatellano (bakeng sa mohlalaample, mola oa 0x10040050, kholomo ea 4 e tšoere boleng ba hexadecimal byte ho 0x10040054. Mosebelisi a ka fetola boleng ba li-byte ka ho penya habeli sele le ho kenya boleng bo bocha ba hexadecimal. Li-byte tse hlophisitsoeng li hlaha ka bofubelu.
Tobetsa konopo ea [Ngola] ho hlophisa leqephe lohle ka boleng bo bocha ba byte mohopolong oa flash oa sesebelisoa.
Konopo ea [Flash] e lumella ts'ebetso ea memori ea flash ho qala ka khetho e khethiloeng. Haeba lebokose la tlhahlobo la [Aterese ea MAC] le khethiloe, mosebelisi a ka hlakisa aterese ea memori moo aterese e khethiloeng ea MAC e bolokiloeng teng. Ha konopo ea [Flash] e tobetsoa, aterese ea MAC e hlophisoa ka mor'a setšoantšo file.

Bapisa Memori ea Sesebelisoa le Setšoantšo File tab ya
Mosebelisi a ka bapisa memori ea sesebelisoa sa hajoale le setšoantšo se khethiloeng file. Litšoantšo tse peli files li hlahisoa 'me liphapang leha e le life li totobatsoa ka bofubelu. .bin le .hex files sebopeho li tšehetsoa.

Ho sebelisa sesebelisoa sa RF-Flasher le liboto tse ling
Sesebelisoa sa RF-Flasher se iphumanela liboto tsa tlhahlobo tsa BlueNRG-1, BlueNRG-2, BlueNRG-LP, le BlueNRG-LPS (tse bonts'itsoeng e le STDK) tse hokahantsoeng le likoung tsa PC tsa USB. E sebelisa STM32 e thusang (e tsamaisoang ke GUI) ho tsosolosa sesebelisoa le ho se beha ka mokhoa oa bootloader oa UART.
Kopo e boetse e sebetsa le liboto tsa tloaelo, e fana ka phihlello e bonolo ea UART ho sesebelisoa se hokahaneng, empa mosebelisi o tlameha ho kenya sesebelisoa ka mokhoa oa bootloader ka letsoho. Ha ho khethoa likou life kapa life tseo e seng tsa STEVAL COM, pop-up e latelang e hlaha:

Ha pop-up ena e hlaha mme ho latela mofuta oa sesebelisoa, mokhoa oa bootloader o kenngoe ka tsela e latelang:

Bakeng sa lisebelisoa tsa BlueNRG-LP le BlueNRG-LPS, mosebelisi o tlameha ho beha phini ea PA10 boleng bo phahameng mme a etse potoloho ea ho seta sesebelisoa (ho boloka PA10 e le boleng bo holimo).
Bakeng sa lisebelisoa tsa BlueNRG-1 le BlueNRG-2, mosebelisi o tlameha ho beha phini ea DIO7 boleng bo phahameng mme a hlophise sesebelisoa bocha (ho boloka DIO7 e le boleng bo holimo).

Mosebelisi a ka boela a beha sekhahla se ratoang sa baud bakeng sa UART fensetereng ea pop-up ebe o tobetsa OK ho khutlela ho GUI.

Hlokomela:
Mosebelisi o tlameha ho qoba ho seta sesebelisoa bocha ha a ntse a sebelisa sesebelisoa sa RF-Flasher, ntle le haeba ComPort Setting pop-up e sebetsa. Haeba sesebelisoa se tsosolositsoe, mosebelisi o tlameha ho fetola koung ea COM ho sebelisa sesebelisoa sa Flasher hape.

Hlokomela:
Ha liboto tsa tloaelo li sebelisoa ka ho fana ka phihlello ea UART ho lisebelisoa tsa BlueNRG-1, BlueNRG-2, BlueNRG-LP, le BlueNRG-LPS ka sehokelo sa USB FTDI, mosebelisi o lokela ho hlahloba habeli nako e amanang le mokhanni oa PC FTDI PC. Sena se lumella boema-kepe bo hokahaneng hore bo tsejoe e le USB virtual COM. Ho mokhanni oa PC oa USB-FTDI, hlahloba habeli lisebelisoa tse amanang le li-driver tsa USB ho [Properties]>[Port
Litlhophiso]>[E tsoetseng pele]. Etsa bonnete ba hore boleng ba nako ea latency bo behiloe ho 1 ms. Tlhophiso ena e khothaletsoa ka matla ho potlakisa ts'ebetso ea memori ea flash ho liboto tsa tloaelo.

Fesetere e kholo ea SWD

Ho sebelisa konopo ea fensetere e kholo ea SWD fensetereng ea mantlha ea ts'ebeliso ea RF-Flasher, mosebelisi o tlameha ho hokela sesebelisoa sa SWD hardware programming/debugging ho sesebelisoa SWD lines (BlueNRG-1, BlueNRG-2, BlueNRG-LP, le BlueNRG-LPS lisebelisoa).
Lisebelisoa tse latelang tsa SWD hardware programming/debugging interfaces lia tšehetsoa, ho nka hore hardware e khethiloeng le lisebelisoa tse amanang le software li tšehetsa sesebelisoa se hokahaneng:

CMSIS-DAP
ST-LINK
J-Sehokelo

Hlokomela
Ho sebelisa J-Link joalo ka adaptara ea debug, mokhanni oa USB o hloka ho fetoloa ho tloha ho mokhanni oa J-Link ho ea ho WinUSB. Sena se ka etsoa habonolo ka ho sebelisa sesebelisoa HYPERLINK Zadig (https://zadig.akeo.ie) ka tsela e latelang:

Khetha J-Link lethathamong la lisebelisoa
Khetha "WinUSB" joalo ka mokhanni

Tobetsa ho [Install Driver] ho kenya mokhanni oa WinUSB

Hlokomela:
Sheba HYPERLINK J-Link OpenOCD websaete (https://wiki.segger.com/OpenOCD) bakeng sa lintlha tse ling.

Hlokomela:
TLHOKOMELISO: Hang ha mokhanni oa J-Link USB o nketsoe sebaka, ha ho software ea SEGGER e tsoang ho J-Link software package e khonang ho buisana le J-Link. Ho sebelisa software ea SEGGER J-Link hape, mokhanni oa USB o hloka ho khutlisetsoa ho ea kamehla.

Mokhoa oa SWD: mokhoa oa ho matha
Setšoantšo file khetho
Sebelisa [Khetha Setšoantšo File] konopo leqepheng la sehlooho kapa u ee ho [File]>[ Bula File…] ho kenya .bin kapa .h ex file. Tsela e feletseng ea ba khethiloeng file e hlaha haufi le konopo mme konopo ea [Flash] e sebetsa qetellong ea file loading.
Tabeng ea Liketso, mosebelisi a ka khetha likhetho tse latelang:

[Netefatsa]: e qobella cheke ho netefatsa hore litaba tsa memori li ngotsoe ka nepo
[Tsireletso ea ho bala]: e thusa ts'ireletso ea ho bala ha sesebelisoa ka mor'a ho hlophisa setšoantšo se khethiloeng file

[Hlakola ka bongata]: e lumella hore sesebelisoa se hlakole ka bongata pele se hlophisa setšoantšo se khethiloeng file
[Apdate Device Memory]: e lumella tafole ea memori ea sesebelisoa hore e ntlafatsoe kamora ts'ebetso ea lenaneo la memori ea flash
[Plug&Play mode]: e lumella mokhoa oa ho etsa plug-and-play flash memory hore o lumelloe/o sitisoe ha ho fumaneha sesebelisoa se le seng feela sa SWD. Tabeng ena, liboto li hlophisoa e le 'ngoe ka nako. Ha ts'ebetso ea lenaneo e phethiloe botong e le 'ngoe, hoa khoneha ho e ntša le ho koala boto e' ngoe.

Ka tsela e iketsang, khetho ea [Miss erase] e haufi le konopo ea [Flash] ha e hlahlojoe, 'me ke maqephe a memori a hlokahalang feela a hlakotsoeng le ho ngoloa ka file dikahare.
Thebo ea [Lenane la likhokahano tse hokahaneng] e bonts'a likhokahano tsohle tse hoketsoeng tsa SWD (CMSIS-DAP, ST-LINK, le J-Link). Tobetsa konopo ea [Refresh] ho nchafatsa lenane la likhokahano tse hoketsoeng.
Mosebelisi a ka boela a khetha hore na ke sebopeho sefe sa hardware sa SWD se tlamehang ho bonts'oa lebaleng la [Interface].
Likonopo tsa [Khetha Tsohle], [U se Khetha Tsohle], le [Fetola Tsohle] li lumella mosebelisi ho hlalosa hore na ke likhokahano life tse hoketsoeng tsa SWD (kaofela, ha ho le e 'ngoe, kapa tse ling tsa tsona) e lokelang ho ba sepheo sa ts'ebetso ea ts'ebeliso. Ka tsela ena, ts'ebetso e tšoanang (ke hore, flash memory programming) e ka etsoa ka nako e le 'ngoe ho lisebelisoa tse ngata.
Konopo ea [Flash] e lumella ts'ebetso ea memori ea flash ho qala ka khetho e khethiloeng. Haeba lebokose la tlhahlobo la [Aterese ea MAC] le khethiloe, mosebelisi a ka hlakisa aterese ea memori moo aterese e khethiloeng ea MAC e bolokiloeng teng. Ha konopo ea [Flash] e tobetsoa, aterese ea MAC e hlophisoa ka mor'a setšoantšo file.
'Setšoantšo File' tab
E khethiloeng file lebitso, boholo, le likahare tse arotsoeng tse lokelang ho hlophisoa memori ea sesebediswa e ka ba viewed ho Setšoantšo File tab ya.

Hlokomela:
[Bapisa Sesebelisoa Memori ho File] e boetse e tšehetsoa ka mokhoa oa SWD, ka likarolo tse tšoanang le tse hlalositsoeng Karolong ea 4.1: Mokhoa oa UART: mokhoa oa ho sebetsa.

Mokhoa oa SWD: bala karolo ea bootloader
Mosebedisi a ka bala karolo ya bootloader ya sesebediswa se hoketsweng ka SWD hardware programming interface ka ho kgetha [Tools]>[Read Bootloader Sector (SWD)]. Likahare tsa lefapha la bootloader li bonts'oa tabeng ea Bootloader/OTP.

Hlokomela:
Karolo ena e tšehetsoa feela ka mokhoa oa SWD mme e fumaneha feela ka GUI.

Mokhoa oa SWD: bala sebaka sa OTP
Mosebedisi a ka bala sesebediswa se hoketsweng sebakeng sa OTP (moo se tshehetswang) a sebedisa SWD hardware programming interface ka ho kgetha [Tools]>[Bala OTP Area (SWD)]. Likahare tsa sebaka sa OTP li hlahisoa tabeng ea Bootloader/OTP.
Ts'ebetso ena ha e sebetse ka mokhoa oa UART.

Mokhoa oa ho etsa lenaneo oa SWD Plug&Play
SWD Plug&Play programming mode e lumella mosebelisi ho kenya loop ea mananeo ka ho hokela sethala se secha sa sesebelisoa hore se hlophisoe. Ha setšoantšo sa memori ea flash file 'me liketso tsa lenaneo li khethiloe, sesebelisoa sa Flasher PC se kopa mosebedisi ho hokahanya sesebelisoa ho sebopeho sa SWD (molaetsa oa E emetse sesebelisoa N. 1 o bontšoa).
Ha mosebelisi a hokahanya sesebelisoa, molaetsa o hokahaneng oa Sesebelisoa sa N. 1 o bonts'oa, 'me sesebelisoa se qala ho hlophisa sesebelisoa ka setšoantšo se khethiloeng. file le dikgetho. Ha ts'ebetso ea lenaneo e felile, sesebelisoa sa Flasher se bonts'a molaetsa Ka kopo, khaola sesebelisoa N. 1. Ha mosebelisi a hakolla sesebelisoa, molaetsa oa E emetse sesebelisoa N. 2 oa hlaha. Mosebelisi a ka emisa mokhoa ona oa othomathike ka ho tobetsa konopo ea [Emisa].
Ha o sebelisa mokhoa oa Plug&Play, mosebelisi o tlameha ho khetha sebopeho se tla sebelisoa (CMSIS-DAP, ST-LINK, kapa J-Link).

Lenaneo la aterese ea MAC

Lenaneo la aterese ea MAC le lumella aterese ea MAC hore e bolokehe sebakeng se itseng sa memori ea flash sesebelisoa.
Mosebelisi a ka khetha ho lumella khetho ena kapa che ka ho hlahloba kapa ho hlakola lebokose la tlhahlobo la [Aterese ea MAC]. Sebaka se ikhethileng sa memori ea flash se setiloe sebakeng sa [MAC Flash location].
Konopo ea [Seta aterese ea MAC] e lumella mosebelisi ho khetha aterese ea MAC ka tsela e latelang:

Sheba lebokose la [Range] 'me u fane ka aterese ea ho qala sebakeng sa [Aterese ea ho Qala]. Aterese ea ho qala ke aterese ea MAC e lokelang ho bolokoa sesebelisoa sa pele se hokahaneng.
- Hoa khonahala ho beha mehato ea tlatsetso ho tloha boleng ba [Aterese ea ho Qala] ka ho kenya palo ea liboto tse tla hlophisoa ho Num. Boards tab, kapa ka ho kenya boleng ba [Aterese ea ho Qetela]:
- Haeba mokhoa oa othomathike o khethiloe ho thebo ea Liketso, lethathamo le khethiloeng la liaterese tsa MAC le sebelisoa bakeng sa ts'ebetso ea ho iketsetsa mananeo. Haeba ho se joalo, ke sesebelisoa se le seng feela se hlophisitsoeng, se sebelisa sebaka sa [Aterese ea ho Qala].
Mosebelisi a ka fana ka lethathamo la liaterese tsa MAC tse tla sebelisoa ka ho kenya letsoho file:
- Sheba [File] checkbox ebe u khetha mongolo o kentsoeng file ka har'a [Moroalo File] tšimong.
- Haeba mokhoa oa othomathike o khethiloe ho thebo ea Liketso, lethathamo le khethiloeng la liaterese tsa MAC le sebelisoa bakeng sa ts'ebetso ea ho iketsetsa mananeo. Haeba ho se joalo, ke aterese ea pele feela e sebelisoang bakeng sa ts'ebetso e le 'ngoe ea lenaneo.

Lebokose la [Boloka Aterese ea MAC] le lumella lethathamo la liaterese tsa MAC tse sebelisitsoeng ho bolokoa ka har'a a file, e khethiloeng ho [File Name] lebala.
Lenaneo la aterese ea MAC le ka kopanngoa le mokhoa oa ho iketsetsa lenaneo. Bakeng sa sesebelisoa se seng le se seng se hokahaneng, setšoantšo file e hlophisitsoe pele, e lateloe ke aterese ea MAC. Palo ea liaterese tsa MAC tse khethiloeng
(kenyeletso ea lenane la liaterese kapa kenyeletso file size) e baka pheletso ea ts'ebetso ea othomathike ea mananeo. Aterese e 'ngoe le e' ngoe e hlophisitsoeng ea MAC e hlaha fensetereng ea Log.
Lenaneo la aterese ea MAC le tšehetsoa ka mokhoa oa UAR le SWD.

Mosebelisi a ka khetha hore na ke nako kapa cheamp e kenyelelitsoe ho tlaleho ea aterese ea MAC e bolokiloeng file lebitso (jwalo ka sehlongoana).
Haeba linakoamp ha e kenyelelitsoe lebitsong la log file, boitsebiso bohle ba log bo bolokoa ka har'a log e tšoanang file. Haeba linakoamp e kenyelelitsoe, tlhahisoleseding ea log bakeng sa ho matha e 'ngoe le e' ngoe e bolokiloe ka har'a log e fapaneng file.
Lebitso la log file e ka hlalosoa ka ho sebelisa [File Name] lebala.

Sesebelisoa sa ho qala RF-Flasher

Sesebelisoa sa RF-Flasher ke sesebelisoa se ikemetseng se lumellang mosebelisi ho tsamaisa litaelo tsa ts'ebeliso ea RF-Flasher a sebelisa RF-Flasher utility GUI.
Ho hlokahala fensetere ea litaelo tsa DOS 'me mekhoa ea UART le SWD e tšehetsoa (ho sebelisoa setšoantšo sa .bin le .hex files).
Sesebelisoa sa RF-Flasher launcher (RF-Flasher_Launcher.exe) se kenyelelitsoe ho sephutheloana sa lisebelisoa tsa RF-Flasher ka har'a foldara ea kopo. "Release folder" ho RF-Flasher utility software package start menu
ntho (ST RF-Flasher utility xxx) e lumella ho fihlella ka ho toba foldareng ea kopo.

Litlhoko
Bakeng sa ho sebelisa sesebelisoa sa RF-Flasher sesebelisoa se itseng, litlhoko tse latelang li tlameha ho finyelloa:

Mokhoa oa UART: sethala sa BlueNRG-1, BlueNRG-2, BlueNRG-LP, kapa BlueNRGLPS se tlameha ho hokahanngoa le koung ea USB ea PC.
SWD mode: sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokeloa le melapo ea BlueNRG-1, BlueNRG-2, BlueNRG-LP, kapa BlueNRG-LPS SWD.

Ka khetho ea -l, mehato eohle ea ts'ebetso e lateloa ho log files, e bolokiloeng ho "Logs" foldareng, e entsoeng ka har'a foldara ea "Application" ea "RF-Flasher" software utility software.

Lisebelisoa tsa lisebelisoa tsa RF-Flasher
Ho sebelisa sesebelisoa sa RF-Flasher sesebelisoa se itseng, mosebelisi o tlameha ho bula khetla ea Windows DOS le ho qala.
RF-Flasher_Launcher.exe ka taelo e nepahetseng, le likhetho (sebelisa -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng).
RF-Flasher_Launcher.exe -h:
Tšebeliso: RF-Flasher Launcher [-h] {flash, bala, mass_erase, verify_memory, erase_pages, uart, swd, bala_OTP,
ngola_OTP}
Mofuta oa ho qala oa RF-Flasher xxx
Likhang tsa boikhethelo:
-h, -help: bonts'a molaetsa ona oa thuso 'me u tsoe ho Litaelo:
{flash, bala, hlakola_ka bongata, netefatsa_memori, hlakola_maqephe, uart, swd, bala_OTP, ngola_OTP}

flash: lenaneo la memori ea flash
bala: bala memori ya flash

mass_erase: hlakola memori ea flash
verify_memory: netefatsa litaba tsa sesebelisoa sa RF ka a file
erase_pages: hlakola leqephe le le leng kapa ho feta mohopolong wa flash

uart: bonts'a likou tsohle tsa COM tse hokahantsoeng (mokhoa oa UART)
swd: bonts'a lisebelisoa tsohle tse hokahaneng ka sebopeho sa SWD: ST-LINK, CMSIS-DAP, J-Link (mokhoa oa SWD)
bala_OTP: bala sebaka sa OTP (ka mokhoa oa SWD feela)

ngola_OTP: ngola sebaka sa OTP (ka mokhoa oa SWD feela)

Sesebelisoa sa ho qala sa RF-Flasher: mekhoa ea UART & SWD
Sesebelisoa sa ho qala sa RF-Flasher se tšehetsa mekhoa e 'meli ea ts'ebetso:

Mokhoa oa UART (hokela sesebelisoa se khethiloeng ho koung ea USB ea PC)

SWD mode (hokahanya mohala o khethiloeng oa BlueNRG-1, BlueNRG-2, BlueNRG-LP, kapa BlueNRG-LPS lisebelisoa tsa SWD ho sesebelisoa sa SWD sa lenaneo/debugging).

Sesebelisoa sa ho qala sa RF-Flasher: sebelisa taelo ea uart ho fumana lethathamo la likou tsohle tse teng tsa COMx (lisebelisoa tse hoketsoeng likoung tsa USB tsa PC):

RF-Flasher_Launcher.exe uart
BOIPENG TSE KHOPANG = COM194 (ST DK), COM160 (ST DK)
Sesebelisoa sa ho qala sa RF-Flasher: sebelisa taelo ea swd ho fumana lethathamo la lisebelisoa tsohle tse fumanehang tse hokahantsoeng tsa SWD hardware programming/debugging:
RF-Flasher_Launcher.exe swd
E KHOPOTSOE KE ST-LINK = HA HO ST-LINK E KHOKANG
E HOKELETSOE KE CMSIS-DAP (nomoro ea seriale ea likhokahano tsa CMSIS-DAP):

07200001066fff333231545043084259a5a5a5a597969908
07200001066dff383930545043205830a5a5a5a597969908
07200001066dff333231545043084255a5a5a5a597969908 E KHOPOTSOE KE J-Link = HA HO J-Link E KHOPOTSOE

Sesebelisoa sa ho qala sa RF-Flasher: taelo ea flash
Ho sebelisa sesebelisoa sa RF-Flasher ho hlophisa mohopolo o itseng oa flash ea sesebelisoa, taelo ea flash e teng (rena khetho ea -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng):
RF-Flasher_Launcher.exe flash -h

Tšebeliso ea flash command
RF-Flasher_Launcher.exe flash [-h] [-aterese START_ADDRESS][-f FILE_TO_FLASH
[FILE_TO_FLASH, …]] [-hlakola] [-netefatsa] [-rp] [-mac] [-mac_address MAC_ADDRESS][-mac_log_file MAC_LOG_FILE][-mac_start MAC_START_ADDRESS | -Mac_file
MAC_FILE_ADDRESS](-kaofela | -d DEVICE_ID) [-verbose {0, 1, 2, 3, 4}] [-l](-UART |
-SWD) [-khafetsa {5,15,25,50,100,125,240,480,900,1800,4000}]

Likhang tsa boikhethelo tsa taelo ea Flash

-aterese START_ADDRESS, --aterese START_ADDRESS: aterese ea ho qala.
-all, -all: lisebelisoa tsohle tse hokahaneng (kou ea COM ka mokhoa oa UART; ID ea ST-LINK, ID ea CMSIS-DAP, le ID ea J-link ka mokhoa oa SWD).
-d DEVICE_ID, -device DEVICE_ID: beha ID ea sesebelisoa sa hardware se sebelisetsoang ho hokahanya (COM port ka mokhoa oa UART; ST-LINK ID, CMSIS-DAP ID, le J-Link ID ka mokhoa oa SWD).

-hlakola, --hlakola: nolofalletsa khetho ea [Erase ea Boima].
-f FILE_TO_FLASH [FILE_TO_FLASH ...], -fileToFlash FILE_TO_FLASH
[FILE_TO_FLASH ...]: lenane la .bin kapa .hex files ho hlophisa sesebelisoa sa RF: sesebelisoa sa BlueNRG-1, BlueNRG-2, BlueNRG-LP, kapa BlueNRG-LPS.
khafetsa {5,15,25,50,100,125,240,480,900,1800,4000}, -frequency {5,15,25,50,100,125,240,480,900,1800,4000}: set frequency value - SWDLINK modality Theko ea kamehla ke 4000.

-h, -help: bonts'a molaetsa ona oa thuso 'me u tsoe.
-l, -log: data ea log.
-mac, -mac: nolofalletsa khetho ea [Aterese ea Mac].

-mac_address -MAC_ADDRESS: sebaka sa memori ea flash moo aterese ea sechaba ea Bluetooth® e bolokiloeng teng.
-Mac_file MAC_FILE_ADDRESS, -mf MAC_FILE_ADDRESS: file e nang le lethathamo la liaterese tsa MAC.
-mac_log_file MAC_LOG_FILE, –ml MAC_LOG_FILE: files e nang le li-log tsa liaterese tsa MAC tse bolokiloeng/tse sa bolokoang le tse sebelisitsoeng/tse sa sebelisoeng.

-mac_start MAC_START_ADDRESS, –ms MAC_START_ADDRESS: aterese ea pele ea MAC.
-rp, --readout_protection: nolofalletsa khetho ea [ReadOut Protection].
-SWD, --swd: SWD modality (ST-LINK, CMSIS-DAP, J-Link hardware programming/debugging tool).

-UART, --uart: Mokhoa oa UART. Boto ea tloaelo e tlameha ho kengoa ka mokhoa oa bootloader (lipini tsa DIO7 holimo ha u ntse u etsa potoloho ea ho seta bocha sesebelisoa sa BlueNRG-1 kapa BlueNRG-2; phini ea PA10 e phahame ha u ntse u lokisa sesebelisoa sa BlueNRG-LP kapa BlueNRG-LPS) pele o etsa opereishene.
-verbose {0, 1, 2, 3, 4}, -verbose {0, 1, 2, 3, 4}: eketsa tlhahiso ea lentsoe; beha boemo ba debug ho fihla ho 4 (feela bakeng sa mokhoa oa SWD le data ea log). Boleng ba kamehla ke 2.
-verify, -verify: nolofalletsa khetho ea [Netefatsa].

Hlokomela:

Haeba mokhoa oa UART o khethiloe, sesebelisoa se tlameha ho hokahanngoa le koung ea PC USB COM 'me khetho ea -UART e tlameha ho sebelisoa. Haeba lisebelisoa tse fetang e le 'ngoe li hokahane le likoung tsa USB tsa PC, khetho ea -all e lumella kaofela hore e khethoe. Ntle le moo, mosebelisi a ka hlakisa boema-kepe bo bong le bo bong ba COM a sebelisa khetho ea -d.
Haeba SWD mode e khethiloe, sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokahanngoa le mela e khethiloeng ea SWD, 'me hoa hlokahala ho sebelisa khetho ea -SWD. Haeba lisebelisoa tse fetang bonngoe li hokahane le PC ka sebopeho sa SWD, khetho ea -all e lumella bohle hore ba khethoe. Ntle le moo, mosebelisi a ka hlakisa sebopeho se seng le se seng a sebelisa khetho ea -d.
The binary file ho jarisoa ho hlalositsoe ho sebelisoa khetho ea -f. Haeba mosebelisi a batla ho hlophisa lisebelisoa tsa BlueNRG-1, BlueNRG-2, BlueNRG-LP, kapa BlueNRG-LPS ka lisebelisoa tse fapaneng tsa binary. files nakong ea lenaneo le le leng la lenaneo, ba ka hlakisa litšoantšo tse fapaneng tsa binary ho latela tatellano ena: BlueNRG-1, BlueNRG-2, BlueNRG-LP, BlueNRG-LPS.
RF-Flasher_Launcher.exe flash -UART -kaofela
– f “C:\{user_path}\BlueNRG-1_2 DK
3.2.2\Firmware\BlueNRG1_Periph_Examples\Micro\Hello_World\BlueNRG-1\Micro_Hell o_World.bin”
– f “C:\{user_path}\BlueNRG-1_2 DK
3.2.2\Firmware\BlueNRG1_Periph_Examples\Micro\Hello_World\BlueNRG-2\Micro_Hell o_World.bin” –l
– f “C:{user_path}\BlueNRG-LP DK 1.4.0\Firmware
\Peripheral_Examples\Examples_MIX\MICRO\MICRO_Dumela_Lefatshe\STEVAL-
IDB011V1\Micro_Hello_World.bin”
– f “C:{user_path}\BlueNRG-LP DK 1.4.0\Firmware
\Peripheral_Examples\Examples_MIX\MICRO\MICRO_Dumela_Lefatshe\STEVAL-
IDB012V1\Micro_Hello_World.bin”
Ea pele file e hlophisitsoe ho lisebelisoa tsa BlueNRG-1 tse hokahaneng; ea bobeli file e hlophisitsoe ho lisebelisoa tsa BlueNRG-2 tse hokahaneng; ea boraro file e hlophisitsoe ho lisebelisoa tsa BlueNRG-LP tse hokahaneng; ea bone file e hlophisitsoeng ho lisebelisoa tsa BlueNRG-LPS tse hokahaneng.
Haeba khetho ea -f e sa sebelisoe, litšoantšo tsa binary filee hlalositsoe ho Application/config_file.conf li sebelisoa:
#Setšoantšo file bakeng sa sesebelisoa sa BlueNRG_1
BLUENRG_1 = “user_path”/bluenrg_1_binary_file.hex
#Setšoantšo file bakeng sa sesebelisoa sa BlueNRG_2
BLUENRG_2 = “user_path”/bluenrg_2_binary.hex
#Setšoantšo file bakeng sa sesebelisoa sa BlueNRG_LP
BLUENRG_LP = “user_path”/bluenrg_lp_binary.hex
#Setšoantšo file bakeng sa sesebelisoa sa BlueNRG_LPS
BLUENRG_LPS = “user_path”/bluenrg_lps_binary.hex
Mosebelisi o tlameha ho hlakisa tsela e felletseng ea setšoantšo sa binary bakeng sa sesebelisoa ka seng.

Sesebelisoa sa ho qala sa RF-Flasher: bala taelo
Ho sebelisa sesebelisoa sa RF-Flasher ho bala mohopolo o itseng oa flash ea sesebelisoa, taelo ea ho bala e teng (sebelisa -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng):
RF-Flasher_Launcher.exe bala -h
Bala tšebeliso ea taelo
RF-Flasher_Launcher.exe bala [-h] [-aterese START_ADDRESS][-boholo SIZE] [–kaofela] [-s] (-kaofela | -d DEVICE_ID)(-UART | -SWD) [-verbose {0, 1, 2, 3, 4}] [-l] [-frequency {5,15,25,50,100,125,240,480,900,1800,4000}]

Bala mabaka a boikhethelo a taelo

-aterese START_ADDRESS, --aterese START_ADDRESS: aterese ea ho qala (boleng ba kamehla ke 0x10040000).
-all, -all: lisebelisoa tsohle tse hokahaneng (kou ea COM ka mokhoa oa UART; ID ea ST-LINK, ID ea CMSIS-DAP, le ID ea J-link ka mokhoa oa SWD).
-d DEVICE_ID, -device DEVICE_ID: beha ID ea sesebelisoa sa hardware se sebelisetsoang ho hokahanya (COM port ka mokhoa oa UART; ST-LINK ID, CMSIS-DAP ID, le J-Link ID ka mokhoa oa SWD).
-kahohle, -hohle: bala memori eohle ea flash.
-khafetsa {5,15,25,50,100,125,240,480,900,1800,4000}, -khafetsa
{5,15,25,50,100,125,240,480,900,1800,4000}: beha boleng ba frequency (feela bakeng sa SWD modality - ST-LINK hardware). Theko ea kamehla ke 4000.
-h, -–help: bonts'a molaetsa ona oa thuso 'me u tsoe.
-l, --log: data ea log.
-s, --show: bonts'a memori ea flash kamora ts'ebetso ea ho bala.
-size SIZE, --boholo SIZE: boholo ba memori ea flash ho bala (boleng ba kamehla ke 0x3000).
-SWD, --swd: SWD modality (ST-LINK, CMSIS-DAP, J-Link hardware programming/debugging tool).
-UART, --uart: mokhoa oa UART. Liboto tsa tloaelo li tlameha ho kenngoa ka mokhoa oa bootloader pele o etsa ts'ebetso ena. Bakeng sa lisebelisoa tsa BlueNRG-LP le BlueNRG-LPS, mosebelisi o tlameha ho beha phini ea PA10 boleng bo phahameng mme a etse potoloho ea ho seta sesebelisoa, ho boloka PA10 e le boleng bo holimo. Bakeng sa lisebelisoa tsa BlueNRG-1 le BlueNRG-2, mosebelisi o tlameha ho beha phini ea DIO7 boleng bo phahameng le ho seta sesebelisoa bocha, ho boloka DIO7 e le boleng bo holimo.
-verbose {0, 1, 2, 3, 4}, -verbose {0, 1, 2, 3, 4}: eketsa tlhahiso ea lentsoe; beha boemo ba debug ho fihla ho 4 (feela bakeng sa mokhoa oa SWD le data ea log). Boleng ba kamehla ke 2.
Haeba mokhoa oa UART o khethiloe, sesebelisoa se tlameha ho hokahanngoa le koung ea PC USB COM 'me khetho ea -UART e tlameha ho sebelisoa. Haeba lisebelisoa tse fetang e le 'ngoe li hokahane le likoung tsa USB tsa PC, khetho ea -all e lumella kaofela hore e khethoe. Ntle le moo, mosebelisi a ka hlakisa boema-kepe bo bong le bo bong ba COM a sebelisa khetho ea -d.
Haeba SWD mode e khethiloe, sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokahanngoa le mela e khethiloeng ea SWD, 'me hoa hlokahala ho sebelisa khetho ea -SWD. Haeba lisebelisoa tse fetang bonngoe li hokahane le PC ka sebopeho sa SWD, khetho ea -all e lumella bohle hore ba khethoe. Ntle le moo, mosebelisi a ka hlakisa sebopeho se seng le se seng a sebelisa khetho ea -d.

Sesebelisoa sa ho qala sa RF-Flasher: taelo ea ho hlakola ka bongata
Ho sebelisa sesebelisoa sa RF-Flasher ho hlakola mohopolo oa flash oa sesebelisoa se itseng,
mass_erase taelo ea fumaneha (sebelisa -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng):
RF-Flasher_Launcher.exe mass_erase -h
Tšebeliso e matla ea ho hlakola taelo
RF-Flasher_Launcher.exe mass_erase [-h] [-s] (-kaofela | -d DEVICE_ID)(-UART | -SWD) [-verbose {0, 1, 2, 3, 4}] [-l][-frequency
{5,15,25,50,100,125,240,480,900,1800,4000}]

Ka bongata hlakola mabaka a boikhethelo ba taelo

-all, -all: lisebelisoa tsohle tse hokahaneng (kou ea COM ka mokhoa oa UART; ID ea ST-LINK, ID ea CMSIS-DAP, le ID ea J-link ka mokhoa oa SWD).
-d DEVICE_ID, -device DEVICE_ID: beha ID ea sesebelisoa sa hardware se sebelisetsoang ho hokahanya (COM port ka mokhoa oa UART; ST-LINK ID, CMSIS-DAP ID, le J-Link ID ka mokhoa oa SWD).
-khafetsa {5,15,25,50,100,125,240,480,900,1800,4000}, -khafetsa
{5,15,25,50,100,125,240,480,900,1800,4000}: beha boleng ba frequency (feela bakeng sa SWD modality - ST-LINK hardware). Theko ea kamehla ke 4000.
-h, --help: bonts'a molaetsa ona oa thuso 'me u tsoe.
-l, --log: data ea log.
-s, --show: bonts'a memori ea flash kamora ts'ebetso ea ho hlakola ka bongata.
-SWD, --swd: SWD modality (ST-LINK, CMSIS-DAP, J-Link hardware programming/debugging tool).
-UART, --uart: mokhoa oa UART. Liboto tsa tloaelo li tlameha ho kenngoa ka mokhoa oa bootloader pele o etsa ts'ebetso ena. Bakeng sa lisebelisoa tsa BlueNRG-LP le BlueNRG-LPS, mosebelisi o tlameha ho beha phini ea PA10 boleng bo phahameng mme a etse potoloho ea ho seta sesebelisoa, ho boloka PA10 e le boleng bo holimo. Bakeng sa lisebelisoa tsa BlueNRG-1 le BlueNRG-2, mosebelisi o tlameha ho beha phini ea DIO7 boleng bo phahameng le ho seta sesebelisoa bocha, ho boloka DIO7 e le boleng bo holimo.
-verbose {0, 1, 2, 3, 4}, -verbose {0, 1, 2, 3, 4}: eketsa tlhahiso ea lentsoe; beha boemo ba debug ho fihla ho 4 (feela bakeng sa mokhoa oa SWD le data ea log). Boleng ba kamehla ke 2.

Hlokomela

Haeba mokhoa oa UART o khethiloe, sesebelisoa se tlameha ho hokahanngoa le koung ea PC USB COM 'me khetho ea -UART e tlameha ho sebelisoa. Haeba lisebelisoa tse fetang e le 'ngoe li hokahane le likoung tsa USB tsa PC, khetho ea -all e lumella kaofela hore e khethoe. Ntle le moo, mosebelisi a ka hlakisa boema-kepe bo bong le bo bong ba COM a sebelisa khetho ea -d.
Haeba SWD mode e khethiloe, sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokahanngoa le mela e khethiloeng ea SWD, 'me hoa hlokahala ho sebelisa khetho ea -SWD. Haeba lisebelisoa tse fetang bonngoe li hokahane le PC ka sebopeho sa SWD, khetho ea -all e lumella bohle hore ba khethoe. Ntle le moo, mosebelisi a ka hlakisa sebopeho se seng le se seng a sebelisa khetho ea -d.

Sesebelisoa sa RF-Flasher se hlahisang: netefatsa taelo ea memori
Ho sebelisa sesebelisoa sa RF-Flasher ho netefatsa dikahare tsa memori ya sesebediswa se itseng, the
verify_memory taelo ea fumaneha (sebelisa -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng):
RF-Flasher_Launcher.exe verify_memory -h

Netefatsa tshebediso ya taelo ya memori
RF-Flasher_Launcher.exe verify_memory [-h] -f FLASH_VERIFY_FILE[-s][-aterese START_ADDRESS](-all | -d DEVICE_ID) [-verbose {0, 1, 2, 3, 4}][-l] (-UART |-SWD)[-frequency {5,15,25,50,100,125,240,480,900,1800,4000],

Netefatsa mabaka a boikhethelo a taelo ea memori

-aterese START_ADDRESS, --aterese START_ADDRESS: aterese ea ho qala bakeng sa netefatso (bakeng sa .bin files feela). Boleng ba kamehla ke 0x10040000.
-all, -all: lisebelisoa tsohle tse hokahaneng (kou ea COM ka mokhoa oa UART; ID ea ST-LINK, ID ea CMSIS-DAP, le ID ea J-link ka mokhoa oa SWD).
-d DEVICE_ID, -device DEVICE_ID: beha ID ea sesebelisoa sa hardware se sebelisetsoang ho hokahanya (COM port ka mokhoa oa UART; ST-LINK ID, CMSIS-DAP ID, le J-Link ID ka mokhoa oa SWD).
-f FLASH_VERIFY_FILE, --file FLASH_VERIFY_FILE: file se sebedisoang ho netefatsa memori ya flash
-frequency {5,15,25,50,100,125,240,480,900,1800,4000}, -frequency {5,15,25,50,100,125,240,480,900,1800,4000}: set hardware modly (SWD) modality (modality SWD). Theko ea kamehla ke 4000.
-h, -–help: bonts'a molaetsa ona oa thuso 'me u tsoe
-l, -–log: data ea log.
-s, --show: bonts'a memori ea flash kamora ts'ebetso ea netefatso
-SWD, --swd: SWD mode (ST-LINK, CMSIS-DAP, J-Link hardware programming/debugging tool).
-UART, --uart: Mokhoa oa UART.
-verbose {0, 1, 2, 3, 4}, -verbose {0, 1, 2, 3, 4}: eketsa tlhahiso ea lentsoe; beha boemo ba debug ho fihla ho 4 (feela bakeng sa mokhoa oa SWD le data ea log). Boleng ba kamehla ke 2.
Haeba mokhoa oa UART o khethiloe, sesebelisoa se tlameha ho hokahanngoa le koung ea PC USB COM 'me khetho ea -UART e tlameha ho sebelisoa. Haeba lisebelisoa tse fetang e le 'ngoe li hokahane le likoung tsa USB tsa PC, khetho ea -all e lumella kaofela hore e khethoe. Ntle le moo, mosebelisi a ka hlakisa boema-kepe bo bong le bo bong ba COM a sebelisa khetho ea -d.
Haeba SWD mode e khethiloe, sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokahanngoa le mela e khethiloeng ea SWD, 'me hoa hlokahala ho sebelisa khetho ea -SWD. Haeba lisebelisoa tse fetang bonngoe li hokahane le PC ka sebopeho sa SWD, khetho ea -all e lumella bohle hore ba khethoe. Ntle le moo, mosebelisi a ka hlakisa sebopeho se seng le se seng a sebelisa khetho ea -d.

RF-Flasher Sesebelisoa sa ho qala: hlakola taelo ea maqephe
Ho sebelisa sesebelisoa sa RF-Flasher ho hlakola leqephe la dikahare tsa memori ea flash sesebelisoa se itseng,
Erase_pages taelo ea fumaneha (sebelisa -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng):
RF-Flasher_Launcher.exe erase_pages -h
Hlakola tšebeliso ea taelo ea maqephe
RF-Flasher_Launcher.exe erase_pages [-h](-UART |-SWD)(-kaofela | -d DEVICE_ID) [-l] [-verbose {0, 1, 2, 3, 4}] [-frequency {5,15,25,50,100,125,240,480,900,1800,4000}] [-s] (-p MAQEPHE | -range RANGE RANGE)

Hlakola maqephe a laela mabaka a boikhethelo

-all, -all: lisebelisoa tsohle tse hokahaneng (kou ea COM ka mokhoa oa UART; ID ea ST-LINK, ID ea CMSIS-DAP, le ID ea J-link ka mokhoa oa SWD).
-d DEVICE_ID, -device DEVICE_ID: beha ID ea sesebelisoa sa hardware se sebelisetsoang ho hokahanya (COM port ka mokhoa oa UART; ST-LINK ID, CMSIS-DAP ID, le J-Link ID ka mokhoa oa SWD).
-h, --help: bonts'a molaetsa ona oa thuso 'me u tsoe.
-l, --log: data ea log.
-khafetsa {5,15,25,50,100,125,240,480,900,1800,4000}, -khafetsa
{5,15,25,50,100,125,240,480,900,1800,4000}: beha boleng ba frequency (feela bakeng sa SWD modality - ST-LINK hardware). Theko ea kamehla ke 4000.
-p MAQEPHE, -Leqephe MAQEPHE: lethathamo la maqephe a lokelang ho hlakoloa (le qala ho 0).
-range RANGE RANGE, -range RANGE RANGE: letoto la maqephe a lokelang ho hlakoloa (moo RANGE ea pele e bonts'ang nomoro e nyane haholo ea leqephe mme ea bobeli RANGE e bonts'a nomoro e phahameng ka ho fetisisa ea leqephe).
-s, --show: bonts'a memori ea flash kamora ts'ebetso ea netefatso.
-SWD, --swd: SWD modality (ST-LINK, CMSIS-DAP, J-Link hardware programming/debugging tool).
-UART, --uart: mokhoa oa UART. Liboto tsa tloaelo li tlameha ho kenngoa ka mokhoa oa bootloader pele o etsa ts'ebetso ena. Bakeng sa lisebelisoa tsa BlueNRG-LP le BlueNRG-LPS, mosebelisi o tlameha ho beha phini ea PA10 boleng bo phahameng mme a etse potoloho ea ho seta sesebelisoa, ho boloka PA10 e le boleng bo holimo. Bakeng sa lisebelisoa tsa BlueNRG-1 le BlueNRG-2, mosebelisi o tlameha ho beha phini ea DIO7 boleng bo phahameng le ho seta sesebelisoa bocha, ho boloka DIO7 e le boleng bo holimo.
-verbose {0, 1, 2, 3, 4}, -verbose {0, 1, 2, 3, 4}: eketsa tlhahiso ea lentsoe; beha boemo ba debug ho fihla ho 4 (feela bakeng sa mokhoa oa SWD le data ea log). Boleng ba kamehla ke 2.
Haeba mokhoa oa UART o khethiloe, sesebelisoa se tlameha ho hokahanngoa le koung ea PC USB COM 'me khetho ea -UART e tlameha ho sebelisoa. Haeba lisebelisoa tse fetang e le 'ngoe li hokahane le likoung tsa USB tsa PC, khetho ea -all e lumella kaofela hore e khethoe. Ntle le moo, mosebelisi a ka hlakisa boema-kepe bo bong le bo bong ba COM a sebelisa khetho ea -d.
Haeba SWD mode e khethiloe, sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokahanngoa le mela e khethiloeng ea SWD, 'me hoa hlokahala ho sebelisa khetho ea -SWD. Haeba lisebelisoa tse fetang bonngoe li hokahane le PC ka sebopeho sa SWD, khetho ea -all e lumella bohle hore ba khethoe. Ntle le moo, mosebelisi a ka hlakisa sebopeho se seng le se seng a sebelisa khetho ea -d.

Sesebelisoa sa ho qala sa RF-Flasher: bala taelo ea OTP
Ho sebelisa sesebelisoa sa RF-Flasher ho bala OTP ea sesebelisoa se itseng, taelo ea read_OTP ea fumaneha (sebelisa -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng):
RF-Flasher_Launcher.exe bala_OTP -h
Bala tšebeliso ea taelo ea OTP
RF-Flasher_Launcher.exe bala_OTP [-h] (tsohle | -d DEVICE_ID) [-aterese OTP_ADDRESS][-nomoro NUM] [-frequency {5,15,25,50,100,125,240,480,900,1800,4000-lver-s] {0,1,2,3,4}]

Bala lintlha tsa boikhethelo tsa taelo ea OTP

-aterese OTP_ADDRESS, -aterese OTP_ADDRESS: aterese ea sebaka sa OTP (ka ho sa feleng: 0x10001800
– ho tsamaellana le mantsoe).
-all, -all: lisebelisoa tsohle tse hokahaneng (ST-LINK ID, CMSIS-DAP ID, le J-link ID ka mokhoa oa SWD).
-d DEVICE_ID, -device DEVICE_ID: beha ID ea sesebelisoa sa hardware se sebelisetsoang ho hokahanya (ST-LINK ID, CMSIS-DAP ID, le J-Link ID ka mokhoa oa SWD).
-frequency {5,15,25,50,100,125,240,480,900,1800,4000}, -frequency {5,15,25,50,100,125,240,480,900,1800,4000}: set hardware modly (SWD) modality (modality SWD). Theko ea kamehla ke 4000.
-h, --help: bonts'a molaetsa ona oa thuso 'me u tsoe.
-l, --log: data ea log.
-palo NUM, -nomoro NUM: palo ea mantsoe a lokelang ho baloa ka har'a sebaka sa OTP. Theko ea kamehla ke 256.
-s, --show: bonts'a sebaka sa OTP.
-verbose {0, 1, 2, 3, 4}, -verbose {0, 1, 2, 3, 4}: eketsa tlhahiso ea lentsoe; beha boemo ba debug ho fihla ho 4 (feela bakeng sa mokhoa oa SWD le data ea log). Boleng ba kamehla ke 2.

Hlokomela:
Taelo ea read_OTP e sebetsa feela ka mokhoa oa SWD. Ka hona, sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokeloa le mela e khethiloeng ea SWD ea sesebelisoa. Haeba lisebelisoa tse fetang bonngoe li hokahane le PC ka sebopeho sa SWD, khetho ea -all e lumella bohle hore ba khethoe. Ntle le moo, mosebelisi a ka hlakisa sebopeho se seng le se seng a sebelisa khetho ea -d.

Sesebelisoa sa ho qala sa RF-Flasher: ngola taelo ea OTP
Ho sebelisa sesebelisoa sa RF-Flasher ho bala OTP ea sesebelisoa se itseng, taelo ea write_OTP ea fumaneha (sebelisa -h ho fumana lethathamo la likhetho tsohle tse tšehetsoeng):
RF-Flasher_Launcher.exe ngola_OTP -h

Ngola tšebeliso ea taelo ea OTP
RF-Flasher_Launcher.exe ngola_OTP [-h] (tsohle | -d DEVICE_ID) -aterese OTP_ADDRESS
-boleng OTP_VALUE [-frequency {5,15,25,50,100,125,240,480,900,1800,4000}] [-l] [-verbose {0,1,2,3,4}]

Ngola mabaka a boikhethelo a taelo ea OTP

-aterese OTP_ADDRESS, -aterese OTP_ADDRESS: aterese ea sebaka sa OTP (kamehla: 0x10001800 - e tsamaellana le lentsoe).
-all, -all: lisebelisoa tsohle tse hokahaneng (ST-LINK ID, CMSIS-DAP ID, le J-link ID ka mokhoa oa SWD).
-d DEVICE_ID, -device DEVICE_ID: beha ID ea sesebelisoa sa hardware se sebelisetsoang ho hokahanya (ST-LINK ID, CMSIS-DAP ID, le J-Link ID ka mokhoa oa SWD).
-frequency {5,15,25,50,100,125,240,480,900,1800,4000}, -frequency {5,15,25,50,100,125,240,480,900,1800,4000}: set hardware modly (SWD) modality (modality SWD). Theko ea kamehla ke 4000.
-h, --help: bonts'a molaetsa ona oa thuso 'me u tsoe.
-l, --log: data ea log.
-s, --show: bonts'a memori ea flash kamora ts'ebetso ea netefatso.
-boleng OTP_VALUE, -boleng OTP_VALUE: boleng ba OTP (lentsoe, joalo ka 0x11223344)
-verbose {0, 1, 2, 3, 4}, -verbose {0, 1, 2, 3, 4}: eketsa tlhahiso ea lentsoe; beha boemo ba debug ho fihla ho 4 (feela bakeng sa mokhoa oa SWD le data ea log). Boleng ba kamehla ke 2.

Hlokomela:
Taelo ea write_OTP e sebetsa feela ka mokhoa oa SWD. Ka hona, sesebelisoa sa SWD hardware programming/debugging se tlameha ho hokeloa le mela e khethiloeng ea SWD ea sesebelisoa. Haeba lisebelisoa tse fetang bonngoe li hokahane le PC ka sebopeho sa SWD, khetho ea -all e lumella bohle hore ba khethoe. Ntle le moo, mosebelisi a ka hlakisa sebopeho se seng le se seng a sebelisa khetho ea -d.
Sesebelisoa sa ho qala sa RF-Flasher: mohlalaamples
Rulahanya setšoantšo sa binary lisebelisoa tse hokahaneng tsa BlueNRG-1 le BlueNRG-2 ka sesebelisoa sa ST-LINK sa hardware (ka mokhoa oa SWD):
RF-Flasher_Launcher.exe flash -SWD -all -f “User_Application.hex” -l
Rulahanya setšoantšo sa binary ho lisebelisoa tse hokahaneng tsa Bluetooth® Low Energy ka likou tsa USB COM (ka mokhoa oa UART):
RF-Flasher_Launcher.exe flash -UART -all -f "User_Application.hex" -l
Rulahanya setšoantšo sa binary ho lisebelisoa tse hokahaneng ka mocha oa CMSIS-DAP u sebelisa ho hlakola, ho netefatsa, le ho boloka likhetho tsa data (ka mokhoa oa SWD):

Nalane ea ntlafatso

Lethathamo la 3. Histori ea ntlafatso ea litokomane

Letsatsi	Phetolelo	Liphetoho
15-May-2018	1	Tokollo ea pele.
03-Jul-2018	2	Setšoantšo se ntlafalitsoeng sa 1. BlueNRG-1, BlueNRG-2 Flasher Utility, Setšoantšo sa 2. Fensetere e kholo ea UART ea Flasher, Setšoantšo sa 3. Mokhoa oa ho sebetsa oa Flasher UART: setšoantšo file , Setšoantšo sa 4. Flasher utility UART mode: mochine oa memori , Setšoantšo sa 5. Flasher utility mode UART: fetola masimo a memori, Figure 7. Flasher Utility: SWD main window, Figure 8. Flasher Utility SWD mode: mochine memori , Setšoantšo sa 10. Sesebelisoa sa Flasher: Mokhoa o itekanetseng oa SWD, Setšoantšo sa 11. Sesebelisoa sa Flasher: UART mode automatic, Setšoantšo sa 12. Sesebelisoa sa Flasher: UART ea ho iketsetsa lenaneo e phethiloe 'me Setšoantšo sa 13. Tšebeliso ea Flasher: Khetho ea aterese ea SWD MAC. Mengolo e nyane e fetoha ho pholletsa le tokomane.
26-Feb-2019	3	E ntlafalitse Selelekela sa Karolo le Mokhoa oa 3.1 oa UART: mokhoa oa ho sebetsa. E kenyellelitsoe Karolo ea 8 ea Sesebelisoa sa Flasher le likarolo tsohle tsa eona.
09-Apr-2019	4	Tšupiso e ekelitsoeng ho "Foldara ea Kopo" Karolong ea 8: Sesebelisoa sa ho qala sa RF-Flasher. Ntlafatso ea Karolo ea 8.4: Sesebelisoa sa ho qala RF-Flasher: taelo ea flash.
14-Jul-2020	5	E fetotsoe BlueNRG-1 le BlueNRG-2 ho sephutheloana sa software sa BlueNRG-X Flasher Tšupiso e ekelitsoeng ho sesebelisoa sa BlueNRG-LP. Setšoantšo se ntlafalitsoeng sa 1. RF-Flasher utility, Figure 3. Flasher utility UART main window, Figure 5. Flasher utility UART mode: The Device Memory tab, Figure 6. Flasher utility mode UART: fetola masimo a memori, Setšoantšo sa 9. Sesebelisoa sa Flasher: Fensetere e ka sehloohong ea SWD, Setšoantšo sa 10. Mokhoa oa SWD oa Flasher: Taba ea Memory ea Sesebelisoa, Setšoantšo sa 14. Tšebeliso ea Flasher: SWD Plug & Play mode, Setšoantšo sa 15. Tšebeliso ea Flasher: Khetho ea aterese ea MAC le Setšoantšo sa 18. RF-Flasher, khetho ea RF-Flasher - flasherify, flasherify, taelo ea flasherify, flasherify
05-Dec-2020	6	Selelekela sa Karolo e Nchafalitsoeng, Karolo ea 2.1: Litlhoko tsa Tsamaiso, Karolo ea 4.1: Mokhoa oa UART: mokhoa oa ho sebetsa, Karolo ea 5: Fensetere e kholo ea SWD, Karolo ea 5.1: Mokhoa oa SWD: mokhoa oa ho sebetsa, Karolo ea 8.1: Litlhoko, Karolo ea 8.2: Likhetho tsa lisebelisoa tsa RF-Flasher launcher, Karolo ea 8.3: RF-Flasher launcher utility: UART & SWD modes, Karolo ea 8.4: RF-Flasher launcher utility: flash command, Karolo 8.5: RF-Flasher launcher utility: bala taelo, Karolo 8.6: RF launcher utility: RF-Flasher utility: Karolo ea 8.7: Sesebelisoa sa RF-Flasher se hlahisang: netefatsa taelo ea memori. E Ekelitsoe Karolo ea 8.8: Sesebelisoa sa RF-Flasher se hlahisang: hlakola taelo ea maqephe.
04-Oct-2021	7	E Ekelitsoe Karolo ea 5.2: Mokhoa oa SWD: bala lefapha la bootloader le Karolo ea 5.3: Mokhoa oa SWD: bala sebaka sa OTP. E ntlafalitse sehlooho, Selelekela sa Karolo, Karolo ea 2: Ho qala, Karolo ea 2.1: Litlhoko tsa Sistimi, Karolo ea 2.2: Ho seta sephutheloana sa software, Karolo ea 3: Sebopeho sa Toolbar, Karolo ea 4: Fensetere e kholo ea UART, Karolo ea 8: RF- Flasher launcher utility, Karolo ea 8.1: Litlhoko, Karolo ea 8.2: Likhetho tsa lisebelisoa tsa RF-Flasher launcher, Karolo ea 8.3: RF-Flasher launcher utility: UART & SWD utility modes, Sectioner-8.4. Karolo ea 8.5: RF-Flasher launcher utility: bala taelo, Karolo ea 8.6: RF- Flasher launcher utility: mass erase command, Karolo ea 8.7: RF-Flasher launcher utility: netefatsa taelo ea memori, Karolo ea 8.8: RF-Flasher launcher utility: hlakola maqephe a taelo: Karolo ea 1.1 litokomane tsa Reference: Karolo ea 1.2.

Letsatsi	Phetolelo	Liphetoho
		Setšoantšo se ntlafalitsoeng 1. RF-Flasher utility, Setšoantšo sa 2. Bapisa tse peli Files tab, Setšoantšo sa 3. Flasher utility UART fensetere e ka sehloohong, Setšoantšo sa 4. Mokhoa oa ho sebetsa oa Flasher UART: Setšoantšo File tab, Setšoantšo sa 5. Mokhoa oa ho sebetsa oa Flasher UART: Taba ea Memori ea Sesebelisoa, Setšoantšo sa 6. Mokhoa oa ho sebelisa Flasher UART: ho fetola masimo a memori, Setšoantšo sa 7. Flasher utility mode UART: Bapisa Memori ea Sesebelisoa le Setšoantšo File tab, Setšoantšo sa 9. Sesebelisoa sa Flasher: Fensetere e ka sehloohong ea SWD, Setšoantšo sa 10. Mokhoa oa SWD o sebetsang oa Flasher: Taba ea Memory ea Sesebelisoa, Setšoantšo sa 16. Sesebelisoa sa Flasher: Lenaneo la aterese ea UART MAC, Setšoantšo sa 17. Tšebeliso ea Flasher: Lenaneo la aterese ea SWD MAC le Setšoantšo sa 18. RF-Flasher: taelo ea flash - launcher.
06-Apr-2022	8	E kentse tšupiso ea BlueNRG-LPS ho pholletsa le tokomane. Ntlafatso ea Karolo ea 8.3: Tšebeliso ea ho qala RF-Flasher: Mekhoa ea UART & SWD le Karolo ea 8.4: RF-Flasher launcher utility: flash command.
10-Jul-2024	9	E ntlafalitsoe: Sehlooho sa tokomane Selelekela sa Karolo Karolo ea 1.1: Lenane la mantsoe a khutsufalitsoeng Karolo ea 1.2: Litokomane tsa litšupiso Setšoantšo sa 1. Sesebelisoa sa RF-Flasher Karolo ea 3: Sehokelo sa Toolbar Setšoantšo sa 3. Flasher utility UART main window Karolo ea 4.1: Mokhoa oa UART: mokhoa oa ho sebetsa Karolo ea 5: Fensetere e kholo ea SWD Karolo ea 5.1: Mokhoa oa SWD: mokhoa oa ho matha Setšoantšo sa 12. Flasher utility SWD mode: bala bootloader Karolo ea 5.3: Mokhoa oa SWD: bala sebaka sa OTP Setšoantšo sa 14. Sesebelisoa sa Flasher: SWD Plug & Play mode Karolo ea 7: Lenaneo la aterese ea MAC Karolo ea 8.1: Litlhoko Karolo ea 8.2: Likhetho tsa lisebelisoa tsa RF-Flasher Karolo ea 8.3: RF-Flasher launcher utility: UART & SWD mekhoa Karolo ea 8.4: RF-Flasher launcher utility: flash command Karolo ea 8.5: RF-Flasher launcher utility: bala taelo Karolo ea 8.6: Sesebelisoa sa ho qala RF-Flasher: taelo ea ho hlakola ka bongata Karolo ea 8.7: Sesebelisoa sa RF-Flasher se hlahisang: netefatsa taelo ea memori Karolo ea 8.8: RF-Flasher launcher utility: hlakola maqephe a taelo Karolo ea 8.9: Sesebelisoa sa ho qala RF-Flasher: bala taelo ea OTP Karolo ea 8.10: Sesebelisoa sa ho qala RF-Flasher: ngola taelo ea OTP

TSEBISO EA BOHLOKOA – BALA KA HLOKO
STMicroelectronics NV le li-subsidiary tsa eona ("ST") li na le tokelo ea ho etsa liphetoho, litokiso, lintlafatso, lintlafatso, le lintlafatso ho lihlahisoa tsa ST le/kapa tokomaneng ena ka nako efe kapa efe ntle le tsebiso. Bareki ba lokela ho fumana lintlha tsa morao-rao tse amanang le lihlahisoa tsa ST pele ba fana ka litaelo. Lihlahisoa tsa ST li rekisoa ho latela lipehelo le maemo a thekiso ea ST ka nako ea tumello ea taelo.
Bareki ke bona feela ba ikarabellang bakeng sa khetho, khetho, le tšebeliso ea lihlahisoa tsa ST mme ST ha e nke e le molato bakeng sa thuso ea kopo kapa moralo oa lihlahisoa tsa bareki.
Ha ho laesense, e hlalositsoeng kapa e boletsoeng, ea tokelo efe kapa efe ea thepa ea mahlale e fanoeng ke ST mona.
Ho rekisoa ha lihlahisoa tsa ST ka litokisetso tse fapaneng le tlhahisoleseding e boletsoeng mona ho tla hlakola waranti leha e le efe e fanoeng ke ST bakeng sa sehlahisoa se joalo.
ST le logo ea ST ke matšoao a khoebo a ST. Bakeng sa lintlha tse ling mabapi le matšoao a khoebo a ST, sheba ho www.st.com/trademarks. Mabitso a mang kaofela a lihlahisoa kapa litšebeletso ke thepa ea beng ba tsona.
Lintlha tse tokomaneng ena li nkela sebaka le ho nkela tlhahisoleseding e neng e fanoe pele liphetolelong tsa pele tsa tokomane ena.
© 2024 STMicroelectronics – Litokelo tsohle li sirelelitsoe
UM2406 - Tšen 9

Litokomane / Lisebelisoa

STMicroelectronics UM2406 The RF-Flasher Utility Software Package [pdf] Bukana ea Mosebelisi
UM2406, UM2406 The RF-Flasher Utility Software Package, The RF-Flasher Utility Software Package, RF-Flasher Utility Software Package, Utility Software Package, Software Package, Package.

Litšupiso

Bukana ea Mosebelisi

STMicroelectronics UM2406 The RF-Flasher Utility Software Package

Litaelo tsa Tšebeliso ea Sehlahisoa