LITŠOANTŠISO TSE MATLA TSA 'MUSO CIR-24NG Customer Interface Relay

Customer InterFACE RELAY SHEET YA TAELO

KHOTHATSO LEKHOTLA - CIR-24NG e ka beoa sebakeng sefe kapa sefe. Ho fanoe ka likoti tse 'nè tsa ho kenya.

KEKETSO MATLA - Bakeng sa matla a 120VAC, hokela CIR-24NG ho liteishene tsa 120V le NEU. Hokela 120VAC e "chesang" e lebisang setsing sa 120V. Bakeng sa ts'ebetso ea 208 ho isa ho 277 VAC, sebelisa li-terminals tsa 277V le NEU. Hokela 277VAC e "chesang" e lebisang setsing sa 277V. Hokela terminal ea NEU ho se nke lehlakore. Hokela terminal ea GND sebakeng sa sistimi ea motlakase. Sebelisa L1 KAPA L2, empa eseng ka bobeli. CIR-24NG e tlameha ho ba le terata Mokhahlelo ho ea ho Boema-fofane, eseng Mokhahlelo ho ea ho Mokhahlelo. Haeba ho se na lehlakore la 'nete le fumanehang, hokela liteishene tsa NEU le GND sebakeng sa sistimi ea motlakase. Theminale ea GND E TLAMEHA ho hokeloa. U SE KE UA tlohela terminal ea GND e sa hokahanngoa.

MAKHOPO METIRI - CIR-24NG e etselitsoe lisebelisoa tsa 2-Wire (Form A) kapa 3-Wire (Form C). Bakeng sa lisebelisoa tsa 2-Wire (Form A), hokela likhoele tsa K le Y ho tloha methareng. Bakeng sa lisebelisoa tsa 3-Wire (Form C), hokela lithapo tsohle tse tharo, K, Y le Z. Joalo ka ha ho loketse 'me ho hlokahala bakeng sa ts'ebeliso ea hau, hokela likhoele tsa K, Y, & Z ho tloha ho Meter #1's dry contact pulse output ho K, Y, & Z ho INNPUT #1 ea mohala oa theminale ka har'a komporo ea lisebelisoa. Hokela Meter #2 ho ea ho K, Y le Z ea Input #2. Li-terminals tsa Y le Z li fana ka "ho huleloa" kutlo voltage ea +13VDC ho ea ho litheminara tsa methara' “Y” le “Z”. Li-terminals tsa "K" tsa CIR-24NG li fana ka phaello e tloaelehileng. Lisebelisoa tsa CIR-24NG tsa KYZ li tsamaisana le li-electromechanical kapa solid state pulse initiator. Ha o sebelisa "open-collector transistor" kapa "open-drain" FET ho hokahanya mithara le CIR-24NG, "transistor emitter pin" kapa "source pin" ea FET e tlameha ho hokeloa ho terminal ea K. 'Mokelli oa transistor kapa phini ea drain ea FET e tlameha ho hokeloa ho li-terminals tsa Y kapa Z.

MOEKETSI TIISETSO – Mehaho ea metara ea CIR-24NG e ka hlophisoa 'me e ka hlophisoa hore e be 2-Wire (Foromo A) kapa 3-Wire (Foromo C). Sheba Leqephe la 3 bakeng sa ho hlophisa lintho tse kentsoeng ke CIR-24NG.

SEHLOOHO TIISETSO - Liphetho tsa CIR-24NG lia hlophiseha 'me li ka hlophisoa joalo ka 2-Wire (Foromo A) kapa 3-Wire (Foromo C). Sheba Leqephe la 3 bakeng sa ho hlophisa liphetho tsa CIR-24NG.

Setšoantšo sa CIR-24NG Wiring

Brayden Automation Corp./Solid State Instruments div. 6230 Aviation Circle
Loveland, CO 80538
(970)461-9600
support@brayden.com
www.solidstateinstruments.com

LIEKETSENG PUSO - Lisebelisoa tse peli tsa 2-Wire (Form A) kapa 3-Wire (Form C) li fanoa ho CIR-24NG. Kenyelletso e 'ngoe le e' ngoe e ka hlophisoa ka boikemelo joalo ka mofuta oa A kapa oa C. Etsa qeto ea sebopeho - 2-Wire kapa 3-Wire - u tla be u sebelisa le metara ebe u hokahanya K le Y bakeng sa Foromo ea A, kapa K, Y le Z bakeng sa Foromo ea C ho lisebelisoa. Kenyelletso ka 'ngoe e fana ka +13VDC wetting voltage ho likhokahano tse omeletseng tsa meter kahoo ha ho hlokahale phepelo ea motlakase e kantle. Ela hloko polarity haeba o sebelisa Bi-Polar open-collector transistor kapa transistor e bulehileng ea FET ho khanna lintho tse kenang tsa CIR-24NG, moo liteishene tsa Y le Z li leng ntle (+) le K terminal e le mpe (-). Kenyelletso e 'ngoe le e 'ngoe ea Y e na le LED e RED ka holim'a terminal ea Y ho bontša ha Y e sebetsa. Kenyelletso e 'ngoe le e 'ngoe ea Z e na le LED e TLHALA ka holimo ho terminal ea Z ho bonts'a ha tlhahiso ea Z e sebetsa.

LIEKETSO - Liphetho tse arohaneng tsa terata tse tharo li fanoe ho CIR-24NG, e nang le li-terminals tsa K1, Y1 & Z1; K2, Y2, & Z2; K3, Y3 & Z3; le K4, Y4 & Z4 'me li fumaneha ka tlas'a sebaka se kampetsoeng ka phaposing ea bareki. Lihlahisoa ke mofuta o tiileng oa boemo bo omeletseng 'me o tlameha ho fuoa matla a ho kolobisatage ho tsoa mohloling o kantle, hangata o fanoa ke sesebelisoa se amohelang pulse. Mabitso a fuoe lintlha tsa 120VAC/VDC MAX 'me hajoale a lekanyelitsoe ho 180mA. Khatello ea nakoana bakeng sa likhokahano tsa li-relay tsa boemo bo tiileng e fanoa ka hare. Relay e 'ngoe le e' ngoe e tlameha ho abeloa kapa ho "maptjoa" ho e 'ngoe ea litsela tse peli tsa ho kenya, ho sebelisa SSI Universal Programmer V1.1.0 kapa hamorao. Liphetho tsa CIR-24NG li ka hlophisoa joalo ka tlhahiso ea Foromo A kapa ea C. Sephetho sa Foromo ea C (3-Wire) ke tlhahiso ea khale ea "Toggle" moo molumo o hlalosoang e le phetoho ea boemo ho tloha ho tsoelo-pele ea KY ho ea ho tsoelo-pele ea KZ kapa visa ka tsela e fapaneng. Li-LED ho sephetho ka seng li bonts'a boemo ba sephetho. Ka mokhoa oa tlhahiso ea Foromo ea C, li-LED tse RED le GREEN li bontša ho koaloa ha KY kapa ho koaloa ha KZ, ka ho latellana. Boemong ba Foromo ea A (2-Wire) "Fixed", ho sebelisoa li-terminals tsa K le Y feela. LED RED e bontša ho koaloa ha KY. Ka mokhoa oa tlhahiso ea Foromo ea A, nako ea ho koala e hlophiselitsoe nako e behiloeng kapa bophara ba ho otla ha pelo. Ho na le bophara ba pulse bo fapaneng ba 8 bo fumanehang.

TS'ELISO LEBAKA - 8 bophara bo fapaneng ba pulse bakeng sa ho koaloa ha Foromo A bo fumaneha ka tsela e latelang: 50, 100, 200, 500, 1000, 2000, 5000, le 10000 mS. Bolelele bo tsitsitseng ba tlhahiso bo ka emisoa ka ho kenya Bokooa ho tsoa lenaneng la ho hula. Ha bolelele bo tsitsitseng bo holofetse, bophara ba pulse bophara bo bonts'a bophara ba pulse, kahoo bo tšoana.

PHAHAMO E KHOLO EA MATLA A LITHO - Lisebelisoa tse hlahisoang li lekantsoe boholo ba 1500 mW. Tlhokomelo e lokela ho nkoa ho netefatsa hore ho kolobisa voltage sebelisitsoeng ho pholletsa le lisebelisoa tse hlahisoang ka makhetlo a hona joale (kapa moroalo) oa ho kenya mochine o tlaase, ha o fete matla a mangata a ho qhala matla a 1500mW. Hangata sena ha se bothata kaha lisebelisoa tse ngata tsa lisebelisoa tse tlase li na le ts'oaetso e phahameng 'me li hlahisa moroalo o tlase haholo, hangata o ka tlase ho 10mA. Bakeng sa mohlalaample, haeba 120VAC e sebelisoa, boholo ba hona joale bo lumelletsoeng ho pholletsa le tlhahiso ke 12.5 mA. Haeba 12VDC e sebelisoa, boholo ba hona joale bo lumelletsoeng ho pholletsa le tlhahiso ke hoo e ka bang 125mA, hantle tlas'a tekanyo ea hona joale ea 180mA ea sesebelisoa. Ka hona, boholo ba dissipation ha u sebelisa 12V ke 1500mW kaha hona joale e lekanyelitsoe ho .125 Amp. Bala boholo ba hona joale u sebelisa foromo e latelang: 1500milliWatts / Voltage = Max. Hona joale (moroalo) ka milliamps. Fetola molumotage kapa ea hona joale e sebelisoang ho pholletsa le tlhahiso ho netefatsa hore boholo ba ho felloa ke matla, voltage le boholo ba hona joale ha bo fete.
FUSES - Phallo ka 'ngoe e na le Fuse ea eona e lekantsoeng ho 250mA F1, F2, F3 le F4 e tsamaellana le liphetho tsa 1, 2, 3, le 4, ka ho latellana. Litekanyo tse kholo tsa fuse li behiloe skrineng sa silika tlas'a kapa haufi le sebaka se seng le se seng sa fuse.

MEKHOA EA HO SEBETSA - CIR-24NG e na le mekhoa e mehlano ea ts'ebetso ka tsela e latelang:

• Foromo ea C In/Foromo C Ho Tsoa - Feta; Nako ea ho koala sephetho e lekana le nako ea ho koala sephetho.
• Form A In/Form A Out – Feta thru; Nako ea ho koala sephetho e lekana le nako ea ho koala sephetho.
• Foromo A In/Form A Out - Feta ka nako e Fixed Width Output.
• Foromo ea A ho / Foromo ea C Ho Tsoa - Mokhoa oa ho Fetola; Liphetoho tsa Output nako le nako ha tlhahiso e fetoha. 5.)
• Foromo ea C In/ Foromo ea A Out - Mokhoa oa Phetoho o nang le nako e tsitsitseng ea ho hlahisa bophara.

Mekhoa ena e abeloa ka Motsoako o khethiloeng oa Input and Output o hlophisitsoeng ho CIR-24NG. Ka hona tlhahiso e 'ngoe le e 'ngoe e abeloa mokhoa o ipapisitseng le Foromo ea Kenyelletso, Foromo ea Output le bophara ba pulse bo abetsoeng, haeba ho hlokahala. Kaha tlhahiso e 'ngoe le e 'ngoe e ka abeloa ka boinotšing, liphetho tse peli kapa ho feta tse entsoeng 'mapeng li ka sebetsa ka mekhoa e fapaneng.

HO SEBETSA LE CIR-24NG RELAY

MEKHOA EA HO SEBELISA: CIR-24NG Programmable Customer Interface Relay e na le mekhoa e 5 ea ho sebetsa. Tse tharo ke mekhoa ea "Pass-Thru" ha tse peli e le mekhoa ea "Conversion".

Mokhoa 1 - Foromo ea C In / Foromo ea C Out: Ka mokhoa ona oa Pass-Thru, bobeli ba ho kenya letsoho le tlhahiso li behiloe ho Foromo ea C (3-wire) mode. Liphetho tsa Foromo ea C li latela tlhahiso ea Foromo ea C. Bophara ba phallo ea sephetho bo lekana le bophara ba sekhahla sa ho kenya letsoho. Letheba le LEFUBEDU le bonts'itsoeng lipalong tsa nako le bonts'a ho koaloa ha KY 'me letheba le FUBEDU la tlhahiso le butswe. Letheba le Letala lipalong tsa nako le bonts'a ho koaloa ha KZ le Green LED ea tlhahiso e butsoitse.

Mokhoa 2 - Foromo ea A In / Foromo ea A Out: Ka mokhoa ona oa Pass-Thru, ho kenya letsoho le tlhahiso li behiloe ho Foromo ea A (2-wire) mode 'me mokhoa o tsitsitseng oa Output Pulse Width o holofetse. Liphetho tsa Foromo ea A li latela tlhahiso ea Foromo A. Bophara ba phallo ea sephetho bo lekana le bophara ba sekhahla sa ho kenya letsoho.

* Zin ha e sebelisoe ka mokhoa oa ho kenya li-2-wire (Form A).

Mokhoa 3 - Foromo ea A In / Foromo ea A Out e nang le Output Pulse Width e tsitsitseng: Ka mokhoa ona oa Pass-Thru, ho kenya letsoho le ho hlahisoa ho behiloe ho Foromo ea A (2-wire) mode. Liphetho tsa Foromo ea A li latela tlhahiso ea Foromo ea A, empa li koalehile bakeng sa nako e khethiloeng ea bophara ba molumo.

Ka mokhoa ona tlhahiso ea Foromo ea A e behiloe ho 50mS, ho fihla ho 10,000mS, kahoo li-pulse tse hlahisoang ke bophara bo tsitsitseng joalokaha ho hlalositsoe ke lebokose la ho kenya Pulse Width. Haeba li-pulse tsa ho kenya li potlakile ho feta li-pulse tsa tlhahiso, ho ka ba le phallo e ngata ka mokhoa ona. Seo se bolela hore li-pulse tsa tlhahiso ha li khone ho tsamaisana le li-pulse tse kenang ka lebaka la lithibelo tsa nako tsa bophara bo tsitsitseng ba pulse. Haeba sena se etsahala, ho tla hlaha LED e pharalletseng e tsamaellanang le (li)phetho tse amehang. Khetha bophara bo bokhutšoane ba Output Pulse Width kapa tima bophara bo tsitsitseng ba pulse, ebe o tobetsa ho , ebe o tobetsa .

Mokhoa 4 - Foromo ea A In / Foromo ea C Out: Mokhoeng ona oa Phetolo, Input e behiloe ho Foromo ea A (2-Wire) 'me tlhahiso e behiloe ho Foromo ea C (3-wire). Ka nako e 'ngoe le e 'ngoe ha ho koaloa foromo ea A, tlhahiso ea Foromo ea C e fetola boemo ho ba boemong bo fapaneng. Ts'ebetso ena ea phetoho e lumella ho kenya le ho tsoa ho pulse ho lekana.

Mokhoa 5 - Foromo ea C In / Foromo ea A Out e nang le Output Pulse Width e tsitsitseng: Mokhoeng ona oa Phetoho, tlhahiso e behiloe ho Foromo ea C (3-Wire) 'me tlhahiso e behiloe ho Foromo ea A (2-wire). Sephetho sa Foromo A se fana ka lebelo le tsitsitseng la bophara ha ho fetoha boemo ba ho kenya foromo ea C. Ho ka 'na ha e-ba le ho phalla ha sekhahla ha sekhahla sa pulse se phahame haholo 'me bophara ba phallo ea phallo e le telele haholo. Ts'ebetso ena ea phetoho e lumella ho kenya le ho tsoa ho pulse ho lekana.

Mokhoeng ona tlhahiso ea Foromo ea A e behiloe ho bophara bo tsitsitseng ba pulse. Fixed Pulse Width e ke ke ea koaloa ka mokhoa ona kaha ke boemo bo seng molaong. Sephetho se tlameha ho hlophisoa ka bophara bo tsitsitseng ba pulse. Haeba ho na le khaphatseho, khutsufatsa nako ea bophara ba phallo ea phallo.

Ho etsa 'mapa oa Tlhahiso e 'ngoe le e 'ngoe ho ea ho Kenyelletso: Liphetho tse 'ne tsa CIR-24NG li tlameha ho abeloa, kapa "mapa", ho kenyelletso eo li e latelang. Tlhahiso efe kapa efe e ka 'na ea etsoa 'mapa ho ea ho tse ling. Litlhophiso tse tloaelehileng ke "13+11" moo liphetho tsa 1 ho isa ho 3 li bonts'itsoeng ho Input #1; Sephetho #4 se bapiloe ho Kenyeletso #2. Phetoho ena e tloaelehile ha lisebelisoa tse ngata li fumana molumo o tšoanang ho tsoa ho #1 ho ea ho #3 le End-Of-Interval pulse e hlahisoang ke #4.

Litholoana tsohle tse 'ne li ka abeloa tlhahiso e le' ngoe e fanang ka likhokahano tse 'ne tse ikhethileng. Kenyelletso e sa sebelisoeng e kanna ea tingoa.
Tlhophiso e 'ngoe e tsebahalang ke "24" moo liphetho tse peli li latelang sephetho se le seng. Bakeng sa mohlalaample dipholo tsa #1 le #2 di latela tlhahiso #1 le diphetho #3 le #4 fol low Input #2. Tokiso ena e sebelisoa bakeng sa ho tsamaisoa le ho amoheloa ha kWh pulses, kapa bakeng sa kwh le kVARh pulses.

Tokiso ea kamehla ea feme e tjena:

• Lipoelo #1 le #2 li entsoe 'mapa ho kenya #1, Input ea Foromo ea C/Liphetho tsa Foromo ea C
• Lipoelo #3 le #4 li entsoe 'mapa ho Input #2, Input ea Foromo ea C/Liphetho tsa Foromo ea C.

Ikopanye le feme bakeng sa tšehetso ea tekheniki ho (888)272-9336.

SSI Universal Programmer

SSI Universal Programmer ke sesebelisoa sa mananeo a thehiloeng lifensetereng bakeng sa CIR-24NG Series le lihlahisoa tse ling tsa SSI. Khoasolla SSI Universal Programmer ho tsoa ho SSI website at www.solidstateinstruments.com/sitepages/downloads.php. Ho na le liphetolelo tse peli tse fumanehang bakeng sa ho khoasolla:
Windows 10 le Windows 7 64-bit Version 1.1.0 kapa hamorao
Windows 7 32-bit V1.1.0 kapa hamorao
Haeba u sebelisa Windows 7, hlahloba komporo ea hau pele ho netefatsa hore u khoasolla mofuta o nepahetseng.

Seta Li-Defaults tsa Feme- U ka seta bocha CIR-24NG ho mefokolo ea feme ka ho hula File menu ebe o kgetha Seta Difactory Defaults. Sena se tla khutlisetsa CIR-24NG Mokhoeng oa Ts'ebetso #1.

Lenaneo la CIR-24NG

Ho beha Litlhophiso tsa CIR-24NG
Beha mefuta ea li-pulse tsa tlhahiso le tlhahiso ea CIR-24NG, tlhahiso ho 'mapa oa tlhahiso le nako ea ho otla ka ho sebelisa USB [Mofuta oa B] Programming Port boto ea CIR-24NG. Litlhophiso tsohle tsa sistimi li lokisoa ho sebelisoa USB Programming Port. Khoasolla software ea SSI Universal Programmer V1.1.0 kapa hamorao, e fumaneha e le khoasollo ea mahala ho tsoa ho SSI websebaka. Ntle le moo, MPG-3 e ka hlophisoa ho sebelisoa lenaneo la terminal joalo ka TeraTerm. Sheba "Ho Hlophisa Ports ea Serial" leqepheng la 9.

Lenaneo la ho qala
Pele o qala lenaneo, hokela thapo ea USB lipakeng tsa komporo ea hau le CIR-24NG. Etsa bonnete ba hore CIR-24NG e matlafalitsoe. Tobetsa ho letšoao la SSI Universal Programmer ho komporo ea hau ho qala lenaneo. K'honeng e kaholimo ho le letšehali u tla bona li-LED tse peli tse etsisitsoeng tsa Green, e 'ngoe e bonts'a hore thapo ea USB e hokahane, e' ngoe e le hore CIR-24NG e hokahane le moetsi oa lenaneo. Etsa bonnete ba hore li-LED tse Tala ka bobeli li "tlile" .

Foromo ea ho Kena
CIR-24NG e na le lintlha tse peli. Mongolo o mong le o mong o ka khethoa joalo ka foromo ea A (2-Wire) kapa Form C (3-Wire). Beha karolo e 'ngoe le e' ngoe bakeng sa palo ea lithapo (kapa "foromo") e hokahaneng le metara. Haeba lithapo tse tharo li tsoa methareng beha tlhahiso ho Foromo ea C. Haeba ho sebelisoa lithapo tse peli feela, seta ho Foromo ea A. Sebelisa menu ea ho hula fatše ho khetha Foromo e nepahetseng ea ho kenya. Sheba setšoantšo sa skrine sa SSI Universal Programmer leqepheng la 7. Hang ha u se u khethile liforomo tseo u li batlang, tlanya. .
Foromo ea Khumo
CIR-24NG e na le lihlahisoa tse 'nè tse ikemetseng tsa 3-Wire. Sehlahisoa se seng le se seng se ka sebetsa ka mokhoa oa lefa oa 3-Wire (Form C) kapa mokhoa oa 2-Wire (Form A). Li-LED tsa Red and Green Output li bonts'a boemo ba phallo ea pulse. Sheba lintlha tse eketsehileng leqepheng la 5. Sebelisa menyetla ea ho hula ea Foromo ea Output bakeng sa tlhahiso e 'ngoe le e 'ngoe ebe u khetha "C" ho hula fatše ebe o tobetsa. .
Sebelisa lebokose la Output Form ho kenya "A" ho khetha mokhoa o tsitsitseng oa FORM A Fixed. Ka mokhoa o tsitsitseng, ho sebelisoa feela tlhahiso ea KY. Ena ke sistimi e tloaelehileng ea 2-Wire moo khokahanyo e hlahisoang hangata-e butsoeng ho fihlela nako eo molumo oa eona o hlahisoang. Ha pulse e hlahisoa, lebitso le koaloa ka nako e lekanang le ea ho kenya kapa bakeng sa nako e behiloeng, ka milliseconds, e khethiloeng ka lebokoseng la Bophara ba Foromo. Mokhoa oa Foromo oa A hangata o amahanngoa le litsamaiso tsa ho metha tsa Matla (kWh). Khetha "A" lebokoseng la ho hula Foromo ea Output ebe o tobetsa .

Etsa Bophara ba Pulse
Haeba o sebelisa tlhahiso ea CIR-24NG's ho Mokhoa oa Foromo A (Fixed), beha nako ea ho koala ea tlhahiso kapa bophara ba sekhahla, se ka khethoang ho 25mS, 50mS, 100mS, 200mS, 500mS,1000mS, 2000mS, 5000mS10000 (1mSXNUMX) ea bobeli) ho sebelisa lebokose la Form A Width. Ha ho etsoa molumo, liteishene tsa KY tsa tlhahiso ea Foromo ea A li tla koala palo e khethiloeng ea milliseconds ebe li bonesa RED Output LED feela. Tlhophiso ena e sebetsa feela ho mokhoa oa tlhahiso ea Foromo A, 'me ha e ame mokhoa oa toggle output. Sebelisa nako e khuts'oane ka ho fetesisa ea ho koala e tla amoheloa ka ts'epo ke lisebelisoa tse amohelang pulse, e le hore u se ke ua fokotsa ho sa hlokahaleng sekhahla se phahameng sa sekhahla sa phallo. U ka boela ua khetha Tlosa ho menu ea ho hula e etsang hore tlhahiso e koalehe ka nako e tšoanang le ea ho kenya. Khetha bophara bo lakatsehang ba pulse ho tloha ho hula ka lebokoseng la Foromo A Width ebe o tobetsa . Haeba mofuta oa tlhahiso e khethiloeng ke Foromo ea C, lebokose la Foromo A Pulse Width le tla putsoa.

Sephetho ho Kenyelletso 'mapeng
CIR-24NG e na le bokhoni ba ho "mapa" e 'ngoe le e' ngoe ea liphetho tse 'ne ho e' ngoe ea tse peli tse kenang. Seo se bolela hore mefuta eohle ea litlhophiso tse feto-fetohang li ka hlophisoa ho sebelisoa 'Mapa oa Output to Input pulldown menus. Khetha hore na u batla hore tlhahiso ka 'ngoe e e latele. Joalokaha u ka bona ho exampLe Leqepheng la 7, Litlhahiso #1 le #3 li entsoe 'mapa ho latela Kenyelletso #1 le Liphetho #2 le #4 li entsoe 'mapa ho latela Kenyeletso #2. Hang ha u se u khethile Input 1 kapa Input 2 ho tsoa lethathamong le leng le le leng la tlhahiso, tobetsa ho .

Bala li-Parameters
Ho bala morao litlhophiso tsa hajoale ho tsoa ho CIR-24NG ka nako efe kapa efe, tobetsa feela . Litlhophiso tsa hajoale ho CIR-24NG li tla hlahisoa.

Seta Botjha Overflow
Haeba tlhahiso ka mokhoa oa Foromo ea A e bokella palo ea likhahla tse kholo ho feta 127, boemo ba Khahomelo bo etsahala. Sena se bolela feela hore ha ho nahanoa ka likhaello tsa nako ho tlhahiso haholo-holo ho Form A Pulse Width, tlhahiso e ke ke ea tsoela pele ho hlahisa likhahla ka lebelo le lakatsehang. Ketsahalong ena, fetola Foromo A Pulse Width ho palo e nyane, tobetsa ebe o tobetsa . Lipontšo tsa Overflow bakeng sa (li)phetho tse maemong a khaphatsehang 'me rejisetara e tsamaellanang le eona e tla beoa bocha.

Ho nka Lintlha ka SSI Universal Programmer
Hape hoa khoneha ho Loka kapa ho hapa data u sebelisa SSI Universal Programmer. Ha ts'ebetso ea ho rema lifate e nolofalitsoe, tlhahisoleseding e fumanoang ho Module kapa methareng e ka kenngoa ho a file. Sena se tla thusa ho leka ho rarolla mathata a nakoana a khokahano. Tobetsa ho Capture pulldown menu ebe u khetha setup. Hang a file lebitso le directory li khethiloe, tobetsa ho Qala Capture. Ho emisa ho Reging, tobetsa ho Stop Capture.

Keletso e khethehileng: Leha ho na le lithapo tse tharo (K,Y, & Z) ho phallo ea molumo, ho tloaelehile ho sebelisa K le Y, kapa K le Z, bakeng sa litsamaiso tse ngata tsa terata tse peli tse hlokang kapa tse lakatsang hore ho be le cymmetrical 50/50 duty cycle. ho otla ha pelo ka nako efe kapa efe. Mokhoa oa ho fetola o sebelisoa bakeng sa litsamaiso tse etsang tlhokomeliso le taolo ea tlhokeho 'me li hloka khafetsa ho arohanngoa kapa "symmetrical pulses". Haeba u le ho FORM C Toggle output pulse mode, ‘me sesebelisoa sa hao se amohelang pulse se sebelisa mehala e ‘meli feela, ‘me sesebelisoa se amohelang pulse se bala feela koalo ea khokahanyo e le pulse(eseng ho bula), ebe boleng ba pulse ea 3-Wire e imenne habeli ho Sesebelisoa sa ho Fumana Pulse.

Lenaneo le nang le Lenaneo la Terminal
CIR-24NG e ka hlophisoa ho sebelisoa lenaneo la terminal joalo ka Tera Term, Putty, Hyperterminal kapa ProComm. Beha sekhahla sa baud bakeng sa 57,600, 8 bit, 1 stop bit mme ha ho na parity. Etsa bonnete ba hore Receive e hlophiselitsoe CR+LF ebe o bulela Local Echo.

Lethathamo la Litaelo tsa CIR-24NG (?)
Bakeng sa thuso ea ho khetha kapa ho sebelisa litaelo tsa seriale ka CIR-24NG, tobetsa feela H kapa ? senotlolo. Sehokelo sa serial ho CIR-24NG se tla khutlisa lethathamo le felletseng la litaelo.

• 'INxy ' – Beha kenyeletso, x-input(1-2) y=Mofuta(C,A)
• 'OUTxy ' - Seta tlhahiso, x-output(1-4) y=Mofuta(C,A)
• 'MAPxy ' – Sephetho sa Mmapa/Sekenyo, x-sephetho(1-4) y=Kenyo(1-2)
• 'Wxy ' – Seta bophara ba sekhahla, x-output(1-4), y-Pulse Width(0-8) (Sheba ka tlase)
• 'CX ' - Ho khaphatseha ho hlakileng (X=1-4)
• 'R ' – Bala Parameters
• 'Z '- Beha Li-Defaults tsa Feme
• 'V ' - Mofuta oa Firmware oa Query

Etsa Bophara ba Pulse
'Wxy '- Pulse Width ka mokhoa oa Foromo A, milliseconds - 25 ho isa ho 10000mS, 100mS kamehla;

Etsa Khetho ea Bophara ba Pulse:

• 'wx0 kapa Wx0 ' - Ho koaloa ha 25mS
• 'wx1 ' kapa 'Wx1 ' - Ho koaloa ha 50mS
• 'wx2 ' kapa 'Wx2 ' - Ho koaloa ha 100mS
• 'wx3 ' kapa 'Wx3 ' - Ho koaloa ha 200mS
• 'wx4 ' kapa 'Wx4 ' - Ho koaloa ha 500mS
• 'wx5 ' kapa 'Wx5 ' - Ho koaloa ha 1000mS
• 'wx6 ' kapa 'Wx6 ' - Ho koaloa ha 2000mS
• 'wx7 ' kapa 'Wx7 ' - Ho koaloa ha 5000mS
• 'wx8 ' kapa 'Wx8 ' - Ho koaloa ha 10000mS

CIR-24NG Programmable Relay.vsd

Litokomane / Lisebelisoa

LITŠOANTŠISO TSE MATLA TSA 'MUSO CIR-24NG Customer Interface Relay [pdf] Litaelo CIR-24NG, Customer Interface Relay, Interface Relay, Customer Relay, Relay

Litšupiso

• Bukana ea Mosebelisi