SelectBlinds 15 Channel Remote Control Programming

Litlhaloso

Moqtage	3V (CR2450)
Maqhubu a Radio	433.92 MHz mahlakore a mabeli
Matla a ho Fetisa	10 milliwatt
Mocheso oa ho sebetsa	14°F ho isa ho 122°F (-10°C ho isa ho 50°C)
RF Modulation	FSK
Mosebetsi oa Lock	Ee
Boemo ba IP	IP20
Sebaka sa phetiso	ho fihla ho 200m (ka ntle)

TŠIRELETSO LITS'ELISO

1. Se ke oa beha enjene sebakeng se mongobo, damp, kapa maemo a mocheso a feteletseng.
2. U se ke ua phunya koloi.
3. U se ke ua khaola antenna. E boloke e hlakile linthong tsa tšepe.
4. Se lumelle bana ho bapala ka sesebelisoa sena.
5. Haeba thapo ea motlakase kapa sehokelo se senyehile, se sebelise
6. Netefatsa hore thapo ea motlakase le antenna li hlakile ebile li sirelelitsoe likarolong tse tsamaeang.
7. Cable e tsamaeang ka marako e lokela ho aroloa hantle.
8. Enjene e lokela ho behoa sebakeng se tšekaletseng feela.
9. Pele o kenya, tlosa lithapo tse sa hlokahaleng 'me u tima lisebelisoa tse sa hlokahaleng bakeng sa ts'ebetso ea motlakase.

TLHOKOMELISO EA BETRI EA KHOPI

1. Tlosa 'me hang-hang u sebelise hape kapa u lahle libeteri tse sebelisitsoeng ho latela melao ea lehae 'me u behelle hole le bana. SE KE UA lahla libeteri ka har'a lithōle tsa ntlo kapa licheseng.
2. Esita le libeteri tse sebelisitsoeng li ka baka kotsi e mpe kapa lefu.
3. Letsetsa setsi sa taolo ea chefo bakeng sa tlhaiso-leseling ea kalafo.
4. CR2450 ke mofuta oa betri o lumellanang.
5. Leshala la leshala la voltagke 3.0V.
6. Libetri tse sa tjhacheheng ha lia lokela ho tjhajwa hape.
7. Se ke oa qobella ho ntša, ho chacha, ho qhaqholla, mocheso o ka holimo ho 50°C / 122°F kapa ho chesa. Ho etsa joalo ho ka baka kotsi ka lebaka la ho tsoa moea, ho lutla kapa ho phatloha ho bakang ho chesoa ke lik'hemik'hale.
8. Netefatsa hore libeteri li kentsoe ka nepo ho latela polarity (+ le -). Se ke oa kopanya libeteri tsa khale le tse ncha, mefuta e fapaneng kapa mefuta ea libeteri, joalo ka alkaline, carbon-zinc, kapa libeteri tse nchafatsoang hape.
9. Tlosa 'me hang-hang u sebelise hape kapa u lahle libetri ho thepa e sa sebelisoeng nako e telele ho latela melao ea lehae.
10. Kamehla sireletsa ka ho feletseng phaposi ea betri. Haeba karolo ea betri e sa koalehe ka mokhoa o sireletsehileng, emisa ho sebelisa sehlahisoa, tlosa libeteri, 'me u li behe hole le bana.

TLHOKOMELO

• KOTSI EA HO NYANA: Sehlahisoa sena se na le konopo ea selefouno kapa betri ea chelete ea tšepe.
• LEFU kapa kotsi e tebileng e ka etsahala ha motho a ka nooa.
• Sele e koetsoeng kapa betri ea selefouno e ka baka Internal Chemical Burns nakong ea lihora tse 2 feela.
• BOLOKA libeteri tse ncha le tse sebelisitsoeng HO FIHLELA BANA.
• Batla tlhokomelo ea bongaka hang ha ho belaelloa hore betri e koetsoe kapa e kentsoe ka har'a karolo efe kapa efe ea 'mele.
• CR 2450, 3V

PUSELETSO RETS'ELAVIEW

Ka kopo bala pele o kenya le ho sebelisa. Boloka litaelo tsena bakeng sa ho li sebelisa nakong e tlang.

LIKONANE LITS'ELISO

P1 KOTANE LEBAKA

TS'ELISITSOE BETRI

• a. Ka bonolo kenya sesebelisoa sa ejector se kenyellelitsoeng lesobeng la lesoba 'me u sebelise khatello e nyane sekoahelong ebe u thella sekoaelo.
• b. Kenya betri (CR2450) ka lehlakoreng le letle (+) le shebile holimo.
• c. Ka bonolo thellela sekoahelo morao ho fihlela molumo oa "tobetsa" o utloahala.

TLHOKOMELISO E TSOANG – THIBA LIMIT SETSING

• a. Tlosa sekoaelo karolong e ka morao ea remote, senotlolo sa senotlolo se hukung e nepahetseng.
• b. Tsamaisa switch ho ea sebakeng sa "Lock" ho tima litaelo tse latelang, remote e tla bontša "L" (notlolo):
  • Fetola Tataiso ea makoloi
  • Ho Beha Moeli o ka Holimo le o ka Tlase
  • Fetola Moedi
  • Roller Mode kapa Sheer Mode
• c. Tsamaisa swichi sebakeng sa "Notlolola" ho lekola lits'ebetso tsohle tse hole, remoutu e tla bontša "U" (notlolola).

* Karolo ena e tsoetseng pele e reretsoe ho sebelisoa kamora hore mananeo ohle a moriti a phetheloe. Mokhoa oa mosebelisi o tla thibela phetoho e sa reroang ea meeli.

KHALE LIKHETHONG

KHETHANG KHALE

• a. Tobetsa "<" konopo ho remoutu ho khetha mocha o tlase.
• b. Tobetsa konopo ea ">" ho remoutu ho khetha mocha o holimo.

PATA MEKHOA E SA SEBELISENG

• a. Press and Hold (about 3 sec) “<” and “>” buttons simultaneously until re-mote control displays “C” (channel).
• b. Tobetsa konopo ea "<" kapa ">" ho khetha palo e hlokahalang ea kanale (pakeng tsa 1 ho isa ho 15).
• c. Tobetsa konopo ea "Emisa" ho netefatsa khetho (mohlalaample bonts'a khetho ea likanale tse 5). LED e tla hlahisa "O" (OK) hang ho netefatsa khetho.

REA QALA

Ho bohlokoa ho netefatsa hore enjene e falimehile ebile e ikemiselitse ho amohela mananeo. Ho etsa sena, tobetsa konopo ea "P1" ho enjene e ka tlase ho motsotsoana o le mong, ho kenya enjene ho tsoa Mokhoa oa Boroko.

SEBELISA / UNPAIR REMOTE TAOLI

HLOKOMELA: Mahe a linotsi le Horizontal Blind Motors SE KE UA BEEP.

• a. Tobetsa konopo ea "P1" (hoo e ka bang 2 sec) hloohong ea enjene ho fihlela motor e matha x1 le beeps x1*.
• b. Metsotsoaneng e latelang e 10, tobetsa o hatelle konopo ea "Emisa" ho remote control ho fihlela motor e matha x2 'me e beps x3*.

* Pheta mokhoa o ts'oanang oa ho hlakola remote control.

FETOHA MOTOR DIRECTION (HAE HLOKAHALA)
Ts'ebetso ena e sebetsa feela ha ho se na meeli. Haeba enjene e na le meeli e holimo le e tlase e behiloeng, o ka fetola tsela feela ka ho tobetsa konopo ea "P1" (hoo e ka bang metsotsoana e 10) hloohong ea motor ho fihlela motor jog x3 le beep x3.

Tobetsa konopo ea "Up" kapa "Down" ho bona hore na moriti o leba moo o batlang.
Haeba u hloka ho khelosa tsela, tobetsa o hatelle (hoo e ka bang metsotsoana e 2) "Holimo" le "Down" ka nako e le 'ngoe ho fihlela motor e matha x1 le beps x1.

 

HO BEHA MEELI E PHAHAMENG LE E TLASE

PHETHA MOELI

• a. Tobetsa konopo ea "Up" ho phahamisa moriti, ebe o tobetsa konopo ea "Stop" ha e le moeling o ka holimo o lakatsehang.
• b. Tobetsa o hatelle (hoo e ka bang metsotsoana e 5) "Holimo" le "Emisa" ka nako e le 'ngoe ho fihlela motor e matha x2 le beeps x3.

PHETHA MOELI

• a. Tobetsa konopo ea "Down" ho theola moriti, ebe o tobetsa konopo ea "Stop" ha e le moeling o batlang o tlase.
• b. Tobetsa o hatelle (hoo e ka bang metsotsoana e 5) "Down" le "Emisa" ka nako e le 'ngoe ho fihlela motor e matha x2 le beeps x3.

*Haeba o tsoa maemong a ho beha moeli pele o qeta li-setting tsa moeli, enjene e tla nka meeli e fetileng.

FETOLA MELIKO

FETOLELA MOLIKO

• a. Tobetsa o hatelle (hoo e ka bang metsotsoana e 5) "Holimo" le "Emisa" ka nako e le 'ngoe ho fihlela motor e matha x1 le beeps x1.
• b. Sebelisa konopo ea "Up" ho phahamisetsa moriti sebakeng se lakatsehang, 'me u sebelise konopo ea "Holimo" kapa "Down" ho etsa phetoho ea ho qetela ha ho hlokahala.
• c. Tobetsa o hatelle (hoo e ka bang metsotsoana e 5) "Holimo" le "Emisa" ka nako e le 'ngoe ho fihlela motor e matha x2 le beeps x3.

FETISISA MOEKETSI

• a. Tobetsa o hatelle (hoo e ka bang metsotsoana e 5) "Down" le "Emisa" ka nako e le 'ngoe ho fihlela motor e matha x1 le beeps x1.
• b. Use “Down” buttonto lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.
• c. Tobetsa o hatelle (hoo e ka bang metsotsoana e 5) "Down" le "Emisa" ka nako e le 'ngoe ho fihlela motor e matha x2 le beeps x3.

RATANG SEEMO

SETELA PAKO E RATOANG

• a. Sebelisa konopo ea "Holimo" kapa "Down" ho isa moriti sebakeng seo u se batlang.
• b. Press and hold one “P2” button on the back of remote control until motor jogs x1 and beeps x1.
• c. Tobetsa 'me u tšoare konopo ea "Emisa" ho fihlela motor e matha x1 le beeps x1.
• d. Hape, tobetsa konopo ea "Emisa" ho fihlela motor e matha x2 le beeps x3.

SEBELISA MAEMO A RATANG
Tobetsa o hatelle (hoo e ka bang metsotsoana e 2)
“Stop” button, motor will move to Favorite position.

TS'ELISENG MOEMO

• a. Tobetsa konopo e le 'ngoe ea "P2" ho fihlela koloi e matha 'me e beps x1.
• b. Tobetsa (hoo e ka bang metsotsoana e 2) "Emisa" ho fihlela motlakase o matha le ho beps x1.
• c. Hape, tobetsa konopo ea "Emisa" ho fihlela motor e matha x1 le beep x1 e telele.

MOKHOA OA HO FETOHA HO TSOA MOKHOENG OA ROLLER / SHEER MODE
ROLLER SHADE MODE - Mokhoa oa kamehla, o lumella ho phahamisa / ho theola moriti khafetsa ka mor'a khatiso e khutšoane.

• a. Press and hold (about 5 sec)“Up” and “Down” buttons simultaneously until motor jogs x1.
• b. Press and hold (about 2 sec)“Stop” button until motor jogs x2 and beeps x3.

Bakeng sa taolo le tokiso e nepahetseng, sebelisa Sheer Shade Mode.

SHEER SHADE MODE - E lumella phetoho e nyane ka mor'a khatiso e khutšoanyane le ho phahamisa / ho theola moriti ka mor'a mochine o molelele

• a. Tobetsa o hatelle (hoo e ka bang metsotsoana e 5) "Holimo" le "Down" ka nako e le 'ngoe ho fihlela motor jog x1.
• b. Press and hold (about 2 sec)“Stop” button until motor jog x1 and beep x1.

HO SEBELISA TAOLAO E TENG E TENG

• a. On the current remote control, press one “P2” button until motor jogs x1 and beeps x1.
• b. Once more, on the current remote control, press one “P2” button until motor jogs x1 and beeps x1.
• c. Ho Remoutu e Ncha, tobetsa konopo e le 'ngoe ea "P2" ho fihlela motor e matha x2 le beeps x3.

*Pheta mokhoa o ts'oanang ho eketsa/tlosa taolo e eketsehileng ea remote.

HO HLOMELA TAOLI E NCHA

Latela litaelo tlas'a karolo ea 1. Para / Unpair Remote Control

FETISISA LEBELO MOTHO

EKETSANG MOTHO LEBELO

• a. Tobetsa konopo e le 'ngoe ea "P2" ho fihlela motor jog x1 le beep x1.
• b. Tobetsa konopo ea "Holimo" ho fihlela motor jog x1 le beep x1.
• c. Hape, tobetsa konopo ea "Holimo" ho fihlela motor jog x2 le beep x1.

*Haeba enjene e se na karabelo, e se e na le lebelo le phahameng kapa le Bonyane.

HLOKOMELA LEBELO

• a. Tobetsa konopo e le 'ngoe ea "P2" ho fihlela motor e matha x1 le beeps x1.
• b. Tobetsa konopo ea "Down" ho fihlela motor e matha x1 le beeps x1.
• c. Hape, tobetsa konopo ea "Down" ho fihlela motor e matha x2 le beeps x1.

*Haeba enjene e se na karabelo, e se e na le lebelo le phahameng kapa le Bonyane.

POTLAKO TS'OANE

HO BATLE PHOSO

BOTHATA – MOTOR E BELA HA 10 HA E SEBELISA

Lebaka
Matla a betritage is low/ Taba ya Solar Panel

Tharollo
Recharge with AC adapter or check connection and positioning of solar panel

PROBLEM – THE MOTOR WILL NOT PR Solution OGRAM OR CONNECT

Lebaka

• Sheba hore na enjene e Moeeng oa Boroko
  Tobetsa konopo ea P1 koloing bakeng sa metsotsoana e 2 ho kenya mokhoa oa ho kopanya.
• Multiple Motors li hlophisitsoe ho tšoana
  Kamehla boloka mocha bakeng sa ho etsa mananeo. Ho sebetsa enjene e le 'ngoe ka nako, beha lienjene tse ling kaofela mokhoeng oa ho robala. Tobetsa konopo ea "P1" (hoo e ka bang metsotsoana e 6) hloohong ea koloi ho fihlela motor e matha x2 le beeps x2.

TS'ELISO

US Radio Frequency FCC Compliance
Sesebelisoa sena se lumellana le Karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:

1. Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi, le
2. Sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.

Thepa ena e 'nile ea lekoa' me ea fumanoa e lumellana le meeli
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Sheba hape kapa o suthise lenakana le amohelang sebakeng se seng.
• Eketsa karohano pakeng tsa thepa le moamoheli.
• Hokela lisebelisoa sebakeng sa seketsoana se fapaneng le seo moamoheli a hokahaneng le sona.
• Ikopanye le morekisi kapa setsebi sa radio/TV se nang le boiphihlelo bakeng sa thuso.

Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tumellano li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.

ISED RSS Tlhokomediso
Sesebediswa sena se tsamaellana le maemo a laesense ya Boqapi, Saense le Ntshetsopele ya Moruo ya Canada e sa dumelleng RSS maemo. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:

1. Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso, le
2. Sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.

LITŠOANTŠI TSA TŠEBELETSO LE TŠ

TŠEBELETSO EA KA HARE
Nakong ea ts'ebetso, haeba motlakase o qala ho lla, sena ke pontšo ea ho tsebisa basebelisi hore matla a motlakase a tlaase 'me a hloka ho lefisoa. Ho tjhaja, hokela boema-kepe ba USB bo bonyenyane enjeneng ka har'a tjhaja ea 5V/2A.

PAKA EA KA NTLE E HLAHANG BATTERE
Nakong ea ts'ebetso, haeba voltagE ha e fumanoa e le tlase haholo, betri e emisa ho sebetsa mme e hloka ho nchafatsoa hape. Ho tjhaja, hokela boema-kepe ba USB bo bonyenyane qetellong ea pakete ea betri ka har'a tjhaja ea 5V/2A.

Ho lahla

• U se ke ua lahla litšila ka kakaretso.
• Ka kopo, sebelisa hape libeteri le lihlahisoa tse senyehileng ka nepo.

Litokomane / Lisebelisoa

SelectBlinds 15 Channel Remote Control Programming [pdf] Bukana ea Mosebelisi 15 Channel Remote Control Programming, Remote Control Programming, Control Programming, Programming

Litšupiso

• Bukana ea Mosebelisi