Tataiso ea ho Qala ka Potlako
IMX91LP4EVK-11CM
i.MX 91 Applications Processor

Mabapi le i.MX 91 EVK

Lelapa la i.MX 91 la li-processor tsa lits'ebetso le thusa ho theha ka potlako lisebelisoa tse ncha tse thehiloeng ho Linux. E ipabola lits'ebetsong tse tsoetseng pele tsa multimedia le liindasteri tsa IoT joalo-joalo. Elevating edge intelligence, li-processor tsa i.MX 91 li fana ka motheo o tiileng bakeng sa lisebelisoa tsa fektheri e bohlale, lehae le bohlale, ofisi e bohlale, sesebelisoa sa bongaka, metering, le sistimi e ntlafalitsoeng ea litšenyehelo. sethala.

Litlhaloso

Karete ea khomphutha:

• i.MX 91 application processor e nang le: – 1x Arm® Cortex®-A55
• LPDDR4 16-bit 2GB
• eMMC 5.1, 32GB
• Taolo ea Matla IC (PMIC)
• Tekanyo ea Matla ADC

Letlapa la motheo:

• Slot ea karete ea MicroSD 3.0
• Lihokelo tse peli tsa USB 2.0 C
• USB 2.0 C e le 'ngoe bakeng sa Debug
• USB C PD e le 'ngoe feela
• M.2 Key-E bakeng sa Wi-Fi/BT/802.15.4
• Boema-kepe bo le bong ba CAN
• Likanale tse 'ne tsa ADC
• 6-axis IMU w/ I3C tšehetso
• Li-Ethernet tse peli tsa 1 Gbps
  - Port1 e ts'ehetsa TSN
  - Port2 e tšehetsa ETER
• Sehokelo sa Katoloso sa I2C
• Audio Codec Support
• Tšehetso ea lihlopha tsa PDM MIC
• RTC e kantle e nang le sele ea tšepe
• 2×20 Pin Katoloso ea I/O

Tseba i.MX 91 EVK

Rea qala

Hlakola khiti
I.MX 91 EVK e romelloa ka thepa e thathamisitsoeng ho Lethathamo la 1.
Lethathamo la 1 - Likahare tsa Kit

Ntho	Tlhaloso
IMX91LP4EVK-11CM	Setšoantšo sa IMX91LP4EVK-11CM
Phepelo ea motlakase	USB C PD 45W, 5V/3A; 9V/3A; 15V/3A; 20V/2.25A e tšehelitsoe
Cable ea Type-C ea USB	USB 2.0 C Male ho USB 2.0 A Male
M.2 Mojule	PN: EAR00409; Wi-Fi 6 / BT 5.2 / 802.15.4 support, basing on NXP IW612
Software	Setšoantšo sa Linux BSP se hlophisitsoeng ho eMMC
Litokomane	Tataiso ea ho Qala ka Potlako

Lokisa Lisebelisoa
Lintho tse latelang ho Lethathamo la 2 li khothaletsoa ho tsamaisa i.MX 91 EVK.
Letlapa la 2 - Lisebelisoa tse fanoeng ke bareki

Ntho	Tlhaloso
Setšoantšo sa T050RDH03-HC	LCD e ts'oanang e bonts'a MODULE 5″ TFT 800X480 RGB
M2-NAND-FALA	Karete ea morali ea M.2 NAND flash
M2-NOR-FALA	M.2 NOR flash morali card
Audio HAT	Boto ea katoloso ea molumo e nang le likarolo tse ngata tsa molumo
8MIC-RPI-MX8	8-microphone array proto board bakeng sa ho nolofalletsa lentsoe

Khoasolla software le lisebelisoa
Ho kenya software le litokomane li fumaneha ho www.nxp.com/imx91evkcm. Tse latelang li fumaneha ho websebaka:
Letlapa la 3 - Software le lisebelisoa

Ntho	Tlhaloso
Litokomane	• Merero, moralo le Gerber files • Tataiso ea ho Qala ka Potlako • Tataiso ea Moralo oa Hardware • i.MX 91 EVK Board User Manual • Tekanyo ea Tšebeliso ea Matla
Ntlafatso ea Software	• Linux BSPs
Litšoantšo tsa Demo	• Kopi ea litšoantšo tsa morao-rao tsa Linux tse fumanehang bakeng sa lenaneo ho eMMC. • IMX91LP4EVK-11CM software e ka fumanoa ho nxp.com/imxsw

Ho theha tsamaiso
Lintlha tse latelang li tla hlalosa mokhoa oa ho tsamaisa setšoantšo sa Linux se kentsoeng pele ho MCIMX91-EVK (i.MX 91).

1. Netefatsa li-switches tsa boot
   Li-switches tsa boot li lokela ho hlophisoa ho qala ho tloha "eMMC", SW1301 [4-1] (Setšoantšo sa 1) li sebelisoa bakeng sa boot, Sheba tafole e ka tlase:

   Sesebelisoa sa BOOT	SW1301[1-4]
   eMMC/uSDHC1	0000

   Ela hloko: 1 = KA 0 = TIMA

2. Hokela thapo ya USB debug
   Hokela thapo ea UART koung ea JP1401 (Setšoantšo sa 1). Hokela pheletsong e 'ngoe ea thapo ho PC e sebetsang joalo ka terminal ea moamoheli.
   Likhokahano tsa UART li tla hlaha ho PC, Boema-kepe ba boraro bo tla sebelisoa e le A55 core debugging.
   Bula fensetere ea terminal (ke hore, Hyper Terminal kapa Tera Term), khetha nomoro e nepahetseng ea boema-kepe ba COM ebe u sebelisa tlhophiso e latelang.
   • Sekhahla sa Baud: 115200bps
   • Litaba tsa data: 8
   • Parity: Ha ho letho
   • Emisa likotoana: 1
3. Hokela ponts'o ea phanele e bapileng
   Hokela karolo e bapileng ea LCD (T050RDH03-HC) ho hlooho ea PIN ea J1001 2×20.
4. Kopanya mouse
   Hokela mouse ho sehokelo sa boema-kepe sa USB2 C J302 ka thapo ea USB C OTG.
5. Hokela phepelo ea motlakase
   Hokela phepelo ea motlakase ea USB C PD ho J301, ebe u matlafatsa boto ka switjha ea SW301.
6. Boot up
   Ha boto e ntse e phahama, u tla bona li-penguin tse 4 li hlaha hukung e kaholimo ho le letšehali la sebali, 'me u tla bona Letšoao la terminal la Linux ka holimo letsohong le letšehali le sebali-nako hukung e kaholimo ho le letona. Kea u lebohela, u tsohile ebile u matha.
   Matha sesebelisoa sa "Go Point for i.MX Applications Processors" ho hlahloba li-demos tse kentsoeng pele. Letšoao la NXP le bonts'oa hukung e kaholimo ho leqele la skrini, qala sesebelisoa sa demo ka ho tobetsa letšoao lena. Sheba tataiso ea basebelisi ho fumana lintlha: https://www.nxp.com/webapp/Download?colCode=GPNTUG.vz

Tlhahisoleseling e 'Ngoe

Liphetoho tsa Boot
SW1301[1-4] ke sesebelisoa sa boot configuration, sesebelisoa sa boot sa kamehla ke eMMC/uSDHC1, joalokaha ho bontšitsoe ho Lethathamo la 4. Haeba u batla ho leka lisebelisoa tse ling tsa boot, u lokela ho fetola li-boot switch hore li be le litekanyetso tse lumellanang le tse thathamisitsoeng ho Lethathamo. 4.
Ela hloko: 1 = KA 0 = TIMA
Lethathamo la 4 - Litlhophiso tsa sesebelisoa sa ho qalisa

MOKHOA THUTO	LITLHAKU TSE KHOLO	LITLHAKU TSE KHOLO	LITLHAKU TSE KHOLO	LITLHAKU TSE KHOLO
Ho tloha ka hare ho fuse	0	0	0	1
Sesebelisoa sa ho jarolla	0	0	1	1
USDHC1 8-bit eMMC 5.1	0	0	0	0
USDHC2 4-bit SD3.0	0	0	1	0
FlexSPI Serial NOR	0	1	0	1
FlexSPI Serial NAND 2K leqephe	0	1	1	1
Reserved	0	1	0	0
Reserved	0	1	1	0

Etsa ho eketsehileng ka Lisebelisoa tsa Liboto

Setšoantšo sa T050RDH03-HC LCD BONTŠA MODULE 5” TFT 800X480, RGB, 120.7 mm x 75.8 mm	M2-NAND-FALA QSPI NAND flash morali card with M.2 interface. Winbond 256MB W25N02KWZEIR (WSON8X6) + GigaDevice 256MB GD5F2GM7REBIG (BGA24)
M2-NOR-FALA QSPI NOR flash morali card with M.2 interface. Micron64MB MT25QU512ABB8E12-0AAT(BGA24)	WiFi/BT/IEEE802.15.4 M.2 Mojule (LBES5PL2EL) Wi-Fi 6, IEEE 802.11a/b/g/n/ac + Bluetooth 5.2 BR/EDR/LE + IEEE802.15.4, NXP IW612 chipset
Audio Board: MX93AUD-HAT Boto ea katoloso ea molumo e nang le likarolo tse ngata tsa molumo	Boto ea Microphone: 8MIC-RPI-MX8 8-microphone array proto board bakeng sa ho nolofalletsa lentsoe.

Tšehetso
Etela www.nxp.com/support bakeng sa lethathamo la linomoro tsa mohala sebakeng sa heno.
Tiisetso
Etela www.nxp.com/warranty bakeng sa tlhaiso-leseling e felletseng ea waranti.

Sesebelisoa sena se lumellana le Karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
(1) Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi, le
(2) Sesebelisoa sena se tlameha ho amohela tšitiso leha e le efe e amoheloang, ho kenyelletsa le tšitiso e ka bakang ts'ebetso e sa batleheng.
Tlhokomeliso ea hore liphetoho kapa tokiso e sa amoheloang ka ho hlaka ke mokha o ikarabellang bakeng sa ho latela melao e ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.
Hlokomela: Sehlahisoa sena se lekoa 'me se fumanoe se lumellana le meeli ea sesebelisoa sa digital sa Sehlopha sa B, ho latela Karolo ea 15 ea Melao ea FCC. Meeli ena e etselitsoe ho fana ka tšireletso e utloahalang khahlanong le tšitiso e kotsi mohahong oa bolulo. Sehlahisoa sena se hlahisa, se sebelisa, 'me se ka khantša matla a maqhubu a seea-le-moea, 'me haeba se sa kengoa le ho sebelisoa ho latela litaelo, se ka baka tšitiso e kotsi likhokahanong tsa radio. Leha ho le joalo, ha ho na tiiso ea hore tšitiso e ke ke ea etsahala setsing se itseng.
Haeba sehlahisoa sena se baka tšitiso e kotsi ea seea-le-moea kapa kamohelo ea thelevishene, e ka lekanyetsoang ka ho tima le ho tima sesebelisoa, mosebelisi o khothalletsoa ho leka ho lokisa tšitiso ka e le 'ngoe kapa ho feta tsa mehato e latelang:

• Sheba hape kapa o suthise lenakana le amohelang sebakeng se seng.
• Eketsa karohano pakeng tsa thepa le moamoheli.
• Hokela lisebelisoa sebakeng sa seketsoana se fapaneng le seo moamoheli a hokahaneng le sona.
• Ikopanye le morekisi kapa setsebi sa radio/TV se nang le boiphihlelo bakeng sa thuso.

Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka se bonyane 20cm pakeng tsa radiator le 'mele oa hau.

www.nxp.com/iMX91EVKCM
NXP le logo ea NXP ke matšoao a khoebo a NXP BV
Mabitso a mang kaofela a lihlahisoa kapa litšebeletso ke thepa ea
beng ba tsona ka ho fapana. © 2024 NXP BV
Nomoro ea Tokomane: 91EVKCMQSG REV 0
Tlhaloso: IMX91LP4EVK-11CM
Aras ID: 91450

Litokomane / Lisebelisoa

NXP i.MX 91 Applications Processor [pdf] Bukana ea Mosebelisi IMX91LP4EVK-11CM, i.MX 91 Applications Processor, i.MX 91, Applications Processor, Processor

Litšupiso

• Bukana ea Mosebelisi