MYNT3D MP012-WH OLED Pene ea Khatiso ea Pontšo
Ka kopo bala bukana ena ea mosebelisi ka botlalo pele u e sebelisa.
TLHOKOMELO
- CHESA KOTSI. Nozzle ea ceramic ea sesebelisoa sena e ka chesa haholo.
- U SE KE UA ama ntlha kapa polasetiki efe kapa efe e qhibilihisitsoeng kapa u ka cha habohloko.
- U SE KE UA lumella ntlha hore e be haufi kapa e kopane le lisebelisoa tse tukang.
- Tsebisa ba bang sebakeng seo hore yuniti e chesa 'me e lokela ho tšoaroa ka hloko.
- Lumella ntlha hore e pholile ka ho feletseng ka mor'a ho sebelisoa le pele u boloka.
- Leqhubu le chesang le ka baka tšenyo libakeng tse pentiloeng, lipolasetiki le lesela haeba li ka siuoa li kopane le lisebelisoa tsena.
- Sebelisa feela 1.75mm ABS le PLA filament.
- SEBELISA MOHOLO FEELA. FIHLELA HO BANA.
TLHOKOMELO
O SE KE oa sebelisa sesebelisoa sena haufi le bate, lishaoara, likotlolo kapa lijana tse ling tse nang le metsi.
Letšoao lena le bontša hore sehlahisoa sena ha sea lokela ho lahloa le litšila tse ling tsa ntlo. Ho thibela kotsi e ka bang teng tikolohong kapa bophelong bo botle ba batho ho lahla litšila ho sa laoleheng, e sebelisa hape ka mokhoa o nang le boikarabelo ho khothaletsa tšebeliso e tsitsitseng ea lisebelisoa.
TLHOKOMELISO: 3D Pen ena - ha e sebelisoa le styrene filament (ABS / HIPS / kapa PC-ABS) - e ka pepesetsa uena le ba bang ka phapusing e le 'ngoe ho styrene, k'hemik'hale e tsejoang ke Naha ea California ho baka mofetše.
www.P65 Litemoso.ca.gov.
SEBELISA SEHLAHISO ENA KA TSOHLE SEBAKANG SA LE MOLEMO O HLENG.
Likaroloana
Ka kopo, nka nakoana ho netefatsa hore u fumane likarolo tsohle.
- Pene ea Khatiso ea 3D
- Adapter ea AC
- Cable ea Matla a USB
- Plastic Screwdriver (bakeng sa ho tlosa lemati la tšebeletso)
- (3) Meqolo ea PLA Filament
- Phillips Screwdriver (bakeng sa ho tlosa nozzle)
Likarolo le Litaolo tsa Pene ea hau ea Khatiso ea 3D
Litaelo tsa Ts'ebetso
- Hokela Adapter ea AC le Cable ea Motlakase oa USB sebakeng sa motlakase. Kenya polaka ka har'a sokete ea motlakase.
Hlokomela: Pene ena ea 3D e ka sebelisoa le libanka tsa motlakase tse hlahisang bonyane 2 amps. Ka tsela ena ha o tlameletsoe ka ntle ho lebota. - Fetola mocheso (haeba o lakatsa) tobetsa konopo ea fepa ebe o lokolla. Ela hloko pontšo ea mocheso 'me u emele hore pene e futhumale mocheso.
- Otlolla pheletso ea filamente ha ho hlokahala 'me u e kenye ka har'a lesoba la ho kenya li-filament ho fihlela e emisa. Tobetsa o hatelle, kapa tobetsa konopo ea phepelo habeli ho kenya likhoele ka pene. Ho thellelisa taolo ea lebelo ho ea holimo ho tla etsa hore ts'ebetso ena e potlake.
- Qala setšoantšo sa hau sebakeng se bataletseng. Polycarbonate, kapa khalase e nang le lesela le tšesaane la sekhomaretsi se ka hlatsuoang se etsa hore ho be le sebaka se nepahetseng sa mosebetsi, empa u ka sebelisa eng kapa eng e bolokehileng mocheso le khoele ea hau e khomarelang.
Tobetsa habeli konopo ea phepelo bakeng sa phepelo e tsoelang pele. Ho tobetsa konopo ea mojaro kapa ho hula hang ho tla tsoa ka mokhoa o tsoelang pele oa phepelo.
Ho Fetola Mebala
- Tlisa 3D Pen ea hau ho fihlela mocheso.
- Tobetsa 'me u tšoare konopo ea ho hula ho fihlela filament e lokolohile.
- Netefatsa hore khoele e ncha e sehiloe ka nepo ebe e kenngoa ka pene.
Tlhokomelo ea Nozzle
- Haeba u lumela hore molomo oa hau o koalehile, tlosa khoele ebe u khaola ntlha e ncha. Ebe u bula lemati la ts'ebeletso 'me u tlose molomo ho hlahloba hore na ho na le sengoathoana se ka tlosoang. Haeba e ntse e koalehile, leka ho phahamisa mocheso ho qhibilihisa clog. Leha ho le joalo, haeba u fumana u sitoa ho tlosa khoele, ka kopo hlokomela hore nozzle e modular ebile e nkeloa sebaka habonolo. Li-nozzles tse ncha li fumaneha ho mynt3d.com.
- Ho hlahloba jeme kapa ho nkela nozzle sebaka, qala ka ho phunya lemati la ts'ebeletso ka sesebelisoa se tšesaane, se bataletseng. Sebelisa screwdriver ea boholo ba likhalase tsa mahlo ea Phillips ho tlosa sekoti se tšoereng molomo. Tlosa molomo ka ntle, u sisinyehe ka hloko haeba u kopana le khanyetso.
Malebela a Potlako
- View video ea rona ea pele ea ho seta ho: www.mynt3d.com/pages/tips
- Sebelisa lithempereichara tse tlase ho feta tseo baetsi ba likhoele ba li khothaletsang bakeng sa liprinta tsa 3D:
- ABS: > 190 C
- PLA: <190 C
- Haeba enjene ea phepelo e qala ho thatafalloa ho emisa ts'ebetso le ho khutlisa filament. Leka ho khaola ntlha e ncha pele u tsoela pele. Haeba enjene e tsoela pele ho sokola ho ka ba le karoloana ea khoele e robehileng e khomaretsoeng ka hare. Sheba karolo ea Tokiso ea Nozzle bakeng sa litaelo tse ling.
Malebela a Filament le Lintlha
- Ha o fetoha ho tloha ho PLA ho ea ho ABS filament, molomo o ka ntša mosi o monyenyane ho tloha mocheso o eketsehileng. PLA e thehiloe limela 'me ha e ntše mosi leha e le ofe o chefo ha e chesa haholo.
- Ho itšetlehile ka hore na filament e sebelisoa joang, polasetiki e ka 'na ea tsoela pele ho tsoa hanyenyane ka mor'a hore konopo ea fepa e lokolloe. Phello ena hangata e bonahala haholoanyane ka PLA mme ke sesupo sa bahatisi ba khoebo ba 3D hape. Ho fokotsa mocheso hanyenyane ho ka thusa.
- Ho eletsoa hore u sebelise konopo ea ho hula feela ha u fetola filament. Haeba filament e tlosoa ka mokhoa o itseng feela, e ka holofala ka har'a moqomo 'me pene e ke ke ea tsoa. Haeba sena se etsahala o lokela ho tlosa filament ka ho feletseng ebe o khaola karolo e holofetseng.
- Boleng ba li-filament bo fapana haholo, esita le mefuta e tsebahalang e ka lokolla lihlopha tse mpe. Haeba pene ea hau ea 3D e sebetsa ka mokhoa o sa tloaelehang, mohato oa pele o motle ke ho leka moqolo o mong oa likhoele. Hape, li-filaments tsa ABS le PLA li senngoa ke mongobo o feteletseng. Ke mokhoa o motle oa ho boloka khoele ea hau sebakeng se tiisitsoeng le se omileng.
Litlhaloso
- Mokhoa oa ho tjhaja: hot melt extrusion
- Phatlalatso ea Khatiso: se nang moeli
- Lebelo la ho fepa: fetohang
- Boitsebiso ba ho Hatisa: ABS/PLA
- Thepa ea Diameter: 1.75 limilimithara
- Nozzle Diameter: 0.60 limilimithara
- Mocheso oa Nozzle: 130-230°C
- Motlakase: 10W
- Kenyeletso ea Matla: EA-5VDC 2A
- Adapter ea Matla: 100-240VAC 50/60Hz
- Boemo ba Lisebelisoa: 175 x 20 x 17mm
- Equipment Boima ba 'mele: 40g
- Setifikeiti: FC CC RoHS
Ho batle phoso
Tiisetso e Lekanyelitsoeng ea Lilemo tse 1
Re ema le lihlahisoa tsa rona mme re fana ka waranti e lekantsoeng ea selemo se le seng e koahelang liphoso tse entsoeng. Ho fumana lintlha tse ling etela: www.mynt3d.com/pages/warranty
Mokhoa oa puisano: MYNT3D
- 159 W Broadway STE 200 PMB 143 Salt Lake City, UT 84101
- support@mynt3d.com
- 800-695-5994
FAQs
Morero oa mantlha oa MYNT3D MP012-WH OLED Display Printing Pen ke ofe?
Pene ea Khatiso ea MYNT3D MP012-WH OLED e etselitsoe lits'ebetso tse kang ho etsa mohlala oa 3D, ho betla, ho ngola, ho etsa prototyping, le thuto ea sebaka.
Ke mefuta efe ea likhoele e tsamaellanang le MYNT3D MP012-WH OLED Display Printing Pen?
MYNT3D MP012-WH e tsamaisana le 1.75mm filaments, ho kenyeletsoa PLA, ABS, le thermoplastics tse ling tse qhibilihang lipakeng tsa 140°C le 230°C.
Ke mocheso ofe o khothalletsoang oa ho sebelisa PLA ka Pente ea Khatiso ea MYNT3D MP012-WH OLED Display?
Mocheso o khothaletsoang oa ho sebelisa PLA le MYNT3D MP012-WH ke 175°C bakeng sa phallo e nepahetseng le ho nepahala.
Advan ke engtage ea ponts'o ea OLED ho Pene ea Khatiso ea MYNT3D MP012-WH OLED Display?
Pontšo ea OLED e lumella basebelisi ho shebella mocheso oa nako ea sebele le phallo ea filament bakeng sa liphetoho tse nepahetseng le ts'ebetso e bonolo.
MYNT3D MP012-WH OLED Display Printing Pen e fihlella joang moralo oa ergonomic?
MYNT3D MP012-WH e bobebe 'me e na le moralo o mosesaane, oa ergonomic o fokotsang mokhathala le o lumellang taolo e ntlafetseng bakeng sa tšebeliso e telele.
Morero oa phepelo e ka fetoloang ho MYNT3D MP012-WH OLED Display Printing Pen ke ofe?
Phepelo e feto-fetohang e lumella basebelisi ho laola lebelo le phallo ea filament bakeng sa taolo e nepahetseng, ebang ke bakeng sa meralo e rarahaneng kapa ho tlatsa kapele.
Ho kenyelletsoa eng ka Pente ea Khatiso ea MYNT3D MP012-WH OLED Display?
MYNT3D MP012-WH e tla le mebala e meraro ea PLA filament, adaptara ea USB, le waranti e lekanyelitsoeng ea selemo se le seng.
Pene ea khatiso ea MYNT3D MP012-WH OLED Display ke bokae?
MYNT3D MP012-WH e boima ba li-ounces tse 11.99, e netefatsa ho nkeha habonolo le tšebeliso e bonolo.
Litšupiso
- Bukana ea Mosebelisi l>
