Khamera ea MXN44C-MOD ea ho lemoha lintho tse tsamaeang 
Buka ea Tataiso

Khamera ea MXN44C-MOD

 

Litaba

Likaroloana

• Khamera ea ho Fumana Ntho e Tsamaeang
• Khamera ea boholo bo boholo ba 'mala o kopantsoeng le kopanyo ea tšebetso ea MOD.
• E lumellana le li-monitor tsa MXN HD-TVI tse nang le yuniti efe kapa efe ea taolo
• Ho fumanoa ha ntho e tsamaeang (batsamai ka maoto, baesekele, likoloi, joalo-joalo)
• Alamo ea Tlhokomeliso ea Molumo (ka sebuela-pele sa MXN HD-TVI)
• 2.07 Mega pixels Full HD SONY CMOS Kamera ea mebala
• 1/2.8" Mobala oa CMOS oa setšoantšo se phahameng sa setšoantšo (STARVIS)
• HD-TVI 1080p 30fps
• Tekanyetso e sa keneleng metsi ea IP69K
• Melemo e mengata (Ka peleview, Lehlakoreview, Moraoview, Tekolo, joalo-joalo)
• Sehokelo sa mofuta oa screw se sa keneleng metsi, 4-pin mini-DIN
• Diagonale 200˚ Viewing angle
• Setšoantšo se tloaelehileng/Seipone se ka fetoloa (ka loop wire)
• Ts'ebetso ea khanya e tlase haholo
• Iris ea elektronike e iketsang
• Microphone e hahelletsoeng (bakeng sa Audio ea tsela e le 'ngoe)
• Boemo ba Mocheso -40˚C ho +80˚C
• Ha e khone ho sisinyeha (10G)
• ECE R10.05 e amohetswe (EMC)

Moving Object Detection Function

Litlhaloso tsa Tekheniki

Sensor ea Litšoantšo : 1/2.8” SONY CMOS Sensor (STARVIS)
Lipikselse tse Sebetsang : 2.07 Mega pixels 1920(H) X 1080(V)
Qeto : 1080 TV line
Sistimi ea ho skena : E tsoela pele
Sephetho sa Video : HD-TVI 4.0, 1080P/30fps
Kenyo ea Molumo : Maekerofounu ea C e Imamelang Haholo
S/N karo-karolelano: Bonyane 48dB (ho AGC e tima)
Bonyane ba khanya: 0.5 Lux (50IRE)
Tšebeliso ea matla: DC 12V, 200mA
Matla a fapaneng: DC 9 ~ 48V
Mocheso o sebetsang: -40ºC ho +80ºC
Viewangle ing : 200˚(Diagonal) x 175˚(Horizontal) x 97˚(E thethehileng)
Litekanyo : Ø 38mm, 59(W) x 38(D) x 50(H) incl. borakete
Boima ba 'mele: Hoo e ka bang. 107g (kakaretso ea boima bo kenyelletsa borakete: 120g)

Ho kenya

▪ Kopano ea lik’hamera

1. Lokisa bracket ea khamera e fanoeng koloing.
2. Lokisa bracket ka khamera ho latela setšoantšo.
3. Fetola viewkh'amera le ho tiisa dikurufu ka thata.

▪ Sekhahla sa lithapo

Etsa lesoba le loketseng (hoo e ka bang Ø 19mm) 'me u kenye grommet ea cable.
Nakoana pele ho ts'ebetso ea ho qetela, ka kopo sebelisa sealant se nepahetseng (bakeng sa thibelo) pakeng tsa lesoba le grommet le pakeng tsa thapo le grommet.

Ho boloka khokahano ea cable

1. Bapisa matšoao a metsu ebe o tobetsa lihokelo mmoho.
   
   
2. Sekela sehokelo sa khamera hodimo ho ya ka tshupanako.
3. Tiisa khokahanyo ea cable ka tieo ho thibela ho kena ha metsi.

Hlokomela!

Warranty e ke ke ea sebetsa haeba bothata bo amana le mongobo / kutu ho sehokelo.

Wiring to Monitor

Tsamaisa thapo ho tloha khamera ho ea ho sehlahlo.

Tloaelehileng / Seipone Phetoho ea setšoantšo

Setšoantšo se Tloaelehileng / Seipone se ka fetoloa ka terata ea GREEN loop:

* terata e tala e sa khaotsoang: Setšoantšo sa MIRROR
* Sekoa sa terata e tala: Setšoantšo se TLOAELEHILENG

Tlhokomeliso !!

1. Pele o hokela, hakolla theminale e ka tlase ho betri ho qoba li-circuits tse khutšoane.
2. Li-plug li lokela ho kenngoa ka ho feletseng ho li-connectors kapa li-jack.
   Khokelo e hlephileng e ka baka ho se sebetse hantle ha yuniti.
3. Cable e senyehileng e ka ama ts'ebetso ea kh'amera mme ea baka ho se sebetse hantle ha khamera kapa ho beha leihlo:
   Qoba thapo e senyehileng!
4. Sireletsa thapo ka ho sebelisa tube e tataisang, phala kapa tsamaisa thapo ka har'a koloi ka hohle kamoo ho ka khonehang.
   Tlhokomeliso! Tsamaisa thapo ka libopeho tsa tlhaho ho thibela ho robeha ha cable.
5. Haholo-holo sebelisa mafura a se nang asiti lipakeng tsa lihokelo tsa mofuta oa screw tse sa keneleng metsi 'me u li tiisa ka thata.

 

 

* Moralo le Litlhaloso li Tla fetoha ntle le tsebiso.

 

Litokomane / Lisebelisoa

Khamera ea MXN MXN44C-MOD ea ho Fumana Ntho e Tsamaeang [pdf] Buka ea Taelo MXN44C-MOD, Khamera ea ho lemoha lintho tse tsamaeang, k'hamera ea MXN44C-MOD e lemohang ntho e tsamaeang, k'hamera ea ho lemoha ntho, k'hamera ea ho lemoha, k'hamera

Litšupiso

• Bukana ea Mosebelisi