MiBOXER SPI-WL4 4 Channel ESP32 WLED Digital Controller

DITAELO TSA TIRISO YA SEHLAHAKA

Sehlahisoa Tšobotsi

• Compatible with multiple types of driver ICs
• 4 output channels with independent control
• Support Miboxer SPI wireless remote control
• Color, dim brightness, pixel points, speed, various dynamic & static modes are adjustable
• Boloka litšoantšo
• Built-in microphone and has a music rhythm function
• Type-C terminal is used for updating or implementing hardware

Parameter ea lihlahisoa

Compatible chips

• WS281X, SK6812/WS2814(RGBW), TM1814, 400kHz，TM1829, USC8903, APA106/P L9823, TM1914, FW1906(GRBCW), USC8904(RGBW), SW2805(RGBCW), SM16825(RGBCW), SW2811(White), WS281X(WWA), APA102, LPD8806, LPD6803, PP9813

Setšoantšo sa Khokahano

Setšoantšo sa Kopo

Pontsho

Tlhaloso ea konopo

Konopo ea Static Mode

• Switch pure static lighting, Short press to R, G, B, C, W

Konopo ea Dynamic Mode:

• Short press to switch dynamic mode

Konopo ea Mokhoa oa 'Mino:

• Short press to switch music mode

Zone Button 1 …4

• Short-press” | ” to open zones, short-press ” O ” to turn off zones

Konopo ea Scenes:

• Long-press S1 to save the current scene Short Short-press S1 to select storage scenes

RGB slider:

• Touching to dim RGB

Pixel points slider:

• While the current LED strip is RGB, a touch slider is used to change the saturation
• While the current LED strip is CCT, the touch slider is used to change the color temperature
• While the current LED strip is in dynamic mode, touch the slider to change parameter 2

Speed slider:

• Touching to set speed
• While the current LED strip is in dynamic mode, touch the slider to change parameter 2

Leseli la slide

• Touching to dim Under music mode, it can adjust the sensitivity of the microphone chip

Khokahano/Tlosa

Sehokelo

1. Power off for 10 seconds and power on again, or short-press “SET.”
2. Press the ” ON” button 3 times within 3 seconds.
3. Green flashing state, then the code is successful.

Link fails if the light doesn’t flash. Please repeat the above steps （Attention: can not link again if the remote has already finished linking）

Hlakola:

1. Power off for 10 seconds and power on again, or short-press “SET.”
2. Press the “ON” button 5 times within 3 seconds.
3. Red flashing state, then clear the code successfully.

Unlink fails if the light doesn’t flash. Please repeat the above steps （Attention: no need to unlink if the light has never been linked）

Choose any control method

APP add Instructions

Download and install the “ WLED Native ” APP

• ISO： Batla and download “WLED Native” in the App Store.
• Android: Batla and download “WLED Native” in the Google Play Store.

1. Power on the WLED controller
2. Open the phone settings and enter WiFi settings, find “MiBoxer-WLED-AP” and connect to it with the password “wled1234.”
3. After a successful connection, it will automatically jump to the WLED page (or enter the websaete 4.3.2.1 ho sebatli ho kenya leqephe la WLED).
4. . Click “WIFI SETTINGS”, set the WiFi account and  password, and click”Save & Connect.”
5. After the addition is completed, you can view the added devices and their IP addresses in the APP.

Tlhophiso ea Strip ea LED
Reboot configuration based on the type of LED strip Data GPIO: 4, 16, 18, 19

IO port configuration
Factory default IO port, modify the port via the following route

Relay Configuration
Tlhophiso ea kamehla ea feme

Tlhophiso ea Mic (Haeba sesebelisoa sena se le teng)
Factory default to use the interior microphone, reboot the configuration via the following instructions

Reboot your device once the configuration is done

Set Button Instruction

• Short press: Power on/off & Link Miboxer SPI Remote.
• Long-press for 1 second: Switch colors.
• Long-press for 10 seconds: Reset the WLED controller and activate the MiBoxer-WLED-AP hotspot.

Khutlisa ho Litlhophiso tsa Feme

1. Konopo Reset
   • Long-press “SET” for 10 seconds.
2. APP Reset
   • Go to the WLED control page and click on the top right corner “Config”.
   • Click on “Security & Updates” at the bottom, and then scroll down to find “Factory reset” and check the box. Click “Save” to reset the controller.

UART downloading firmware

• WLED official firmware downloading：https://install.wled.me/

1. Install serial port driver CH340K
2. Download through the website page or esp32 tool software, review more details on the WLED websebaka

Tharollo ea mathata le Tharollo

Taolo ea PC
Type the IP address of your device into a browser to enter into PC control interface while the APP configuration is completed ( the device should be in the same LAN network). PC configuration is the same as the APP

Tlhokomeliso

1. Ka kopo tima motlakase pele o kenya.
2. Ka kopo etsa bonnete ba hore o kenya letsohotage ho tšoana le litlhoko tse tsoang ho sesebelisoa.
3. Don’t disassemble the device if you are not an expert; otherwise, you will damage it.
4. Please do not use the light in places with a wide range of metal areas or strong electromagnetic waves nearby; otherwise, the remote distance will be seriously affected.

Boithorollo

1. Khamphani ea rona e tla ntlafatsa litaba tsa bukana ena ho ipapisitse le ntlafatso ea ts'ebetso ea sehlahisoa. Lintlafatso li tla hlahisoa phetolelong ea morao-rao ea bukana ena, ntle le tsebiso e 'ngoe.
2. Ka lebaka la ho tsoela pele ho sebelisa theknoloji e ncha, litlhaloso tsa sehlahisoa li ka fetoha ntle le tsebiso e 'ngoe.
3. This manual is provided for reference and guidance only and does not guarantee complete consistency with the actual product. The actual application should be a aa pc.
4. Likarolo le lisebelisoa tse hlalositsoeng bukeng ena ha li emele tlhophiso e tloaelehileng ea sehlahisoa. Sebopeho se ikhethileng se ipapisitse le sephutheloana.
5. Lingoliloeng tsohle, litafole le litšoantšo tse bukeng ena li sirelelitsoe ke melao e amehang ea naha 'me li ka se sebelisoe ntle le tumello ea rona.
6. This product may be compatible with third-party products, but our company does not take responsibility for compatibility issues or partial loss of functionality caused by changes in third-party products.

LBH

How do I update the firmware of the controller?

To update or implement hardware, use the Type-C terminal provided on the controller for firmware updates as per the instructions in the manual.

What driver ICs are compatible with this controller?

The controller is compatible with various driver ICs including WS281X, SK6812, TM1814, APA106, and more. Refer to the manual for a complete list of compatible chips.

How do I save custom lighting scenes?

To save a custom scene, long press the Scenes Button to save the current scene. Short press the Scenes Button to select and activate saved scenes.

Litokomane / Lisebelisoa

MiBOXER SPI-WL4 4 Channel ESP32 WLED Digital Controller [pdf] Bukana ea Mosebelisi SPI-WL4, C10, SPI-WL4 4 Channel ESP32 WLED Digital Controller, SPI-WL4, 4 Channel ESP32 WLED Digital Controller, ESP32 WLED Digital Controller, WLED Digital Controller, Digital Controller, Controller

Litšupiso

• Bukana ea Mosebelisi