LIGHTWARE TBP6 Button Panel

Tlhahisoleseding ya Sehlahiswa

Litlhaloso

• Mohlala: Liphanele tsa TBP6-EU-W, TBP6-EU-K
• Likonopo: 2 (ho omella)
• Konopo Backlight: E felletseng kapa Halofo
• Li-LED: Boemo ba LED, Button LEDs 1-6
• Mofuta oa Sehokelo: Phoenix Connector
• Keletso ea Cable: AWG24 (0.2 mm2 bophara) kapa 8×0.22 mm2 thapo ya alamo

Litaelo tsa Tšebeliso ea Sehlahisoa

Tobetsa konopo ea Panel
Ho seta konopo ea konopo, latela mehato ena:

1. Hokela konopo ea konopo boema-kepe ba GPIO ea matrix u sebelisa thapo e khothaletsoang.
2. Kenya lileibole tse lakatsehang bakeng sa likonopo tse tsoang leqepheng le khomaretsoeng.
3. Ho tima khanya e ka morao kapa boemo ba LED, u se ke ua hokahanya likhokahano tsa 7th tsa lihokelo tsa GPIO kapa ua beha boemo ba Output ba pin7 ho ea ho Low ka har'a sesebelisoa sa Lightware.

Mesebetsi ea konopo
Likonopo tse tšeletseng tsa phanele li na le mesebetsi e latelang:

Konopo	Mosebetsi	Ketso e Lemohileng
L1	Fetolela Laptop1 ho Projector (RX97)	Phetoho ea crosspoint
L2	Fetolela Laptop2 ho Projector (RX97)	Phetoho ea crosspoint
PC LEBONA ON/O TIMA	Fetolela boemo ba On/Off ea Siling lamp	Fetola khokahano ea Relay
PROJ ON	Ho bulela Projector	Ho romela molaetsa ka RS-232
PROJ HLOKOMELA	Ho tima Projector	Ho romela molaetsa ka RS-232

Maemo a Jumper
Leseli le ka morao la likonopo le ka behoa ho khanya (e tletseng) kapa e tlaase (halofo) ka ho beha jumper ho JP1 kapa JP2.

Phoenix Connector Wiring
Bakeng sa wiring e nepahetseng, sebelisa thapo e khothalletsoang ea AWG24 kapa 8 × 0.22 mm2 bakeng sa likhokahano.

Malebela le maqheka ka Pin7
Pini ea 7th ea khokahano ea GPIO e ka sebelisoa bakeng sa mesebetsi e fapaneng, ho kenyelletsa le ho matlafatsa konopo ea backlight. Beha tataiso ea phini ho Output le boemo ho ea Holimo ho software ea Lightware Device Controller.

LBH

• P: Nka tima lebone la backlight kapa boemo ba LED joang?
  A: Ho thibela khanya ea morao kapa boemo ba LED, u se ke ua hokahanya likhokahano tsa 7th tsa li-connectors tsa GPIO kapa ua beha boemo ba Output ba pin7 ho ea tlaase ho sesebelisoa sa Lightware.
• P: Ke thapo efe eo ke lokelang ho e sebelisa bakeng sa ho hokahanya konopo ea konopo?
  A: Ho khothalletsoa ho sebelisa cable ea AWG24 kapa 8 × 0.22 mm2 cable bakeng sa ho hokahanya hantle.
• P: Nka beha khanya ea backlight ea likonopo joang?
  A: Khanya ea backlight e ka hlophisoa ho tlala kapa halofo ka ho beha jumper ho JP1 kapa JP2.

Litaelo tsa Bohlokoa tsa Tšireletso

Ka kopo bala tokomane ea litaelo tsa polokeho e fanoeng pele u sebelisa sehlahisoa 'me u lule u le teng bakeng sa tšebeliso ea nako e tlang.

Selelekela
Phanele ea konopo ea TBP6 e ne e etselitsoe hore e sebelisoe le karolo ea taolo e hahelletsoeng ka har'a Motsamaisi oa Ketsahalo ho khetha Lightware matrix switcher le lihlahisoa tsa extender. Phanele ea likonopo e ka kenngoa likamoreng tsa kopano ho etsa liketso tsa mantlha tsa taolo ea sistimi joalo ka khetho ea ho kenya, ho bulela / tima sistimi, ho eketsa kapa ho theola molumo, jj.
Sehlahisoa sena se na le boemo ba LED le khanya e ka morao, e feptjoang ho tloha pineng ea 7 ea GPIO connector. Leseli le ka morao le ka tima, kapa matla a lona a ka behoa maemong a mabeli ka thuso ea li-switches tse tloaelehileng tsa jumper.

Motsamaisi oa Ketsahalo
Motsamaisi oa Ketsahalo ke tšobotsi e bohlale, e hahelletsoeng kahare ho Lightware HDBaseTTM e sebeletsanang le lelapa la TPS extender, mohala oa MODEX le ho li-switcher tse ling tsa matrix joalo ka letoto la MMX8x4. Karolo e ka etsoa ka sesebelisoa sa Lightware Device Controller (LDC). Motsamaisi oa Ketsahalo o sebetsana le liphetoho tsa boemo ba kahare kapa litšebelisano tsa basebelisi ntle le sistimi efe kapa efe ea taolo ea kantle. Ketsahalo e lemohileng e bitsoa Condition, karabelo e bitsoa Ketso.

Litaba tsa Lebokose

Li-caps tse pepeneneng ha li behoe holim'a li-buttons, ka hona, u ka kenya mangolo a lakatsehang habonolo 'me u lokise li-caps - bona karolo e amanang le eona.

FEELAVIEW

Pele View

• Li-labels tsa likonopo ke tsa papiso kaha li-button caps ha li na letho. Mosebedisi a ka kenya laibole eo a e batlang ho tswa letlakaleng le kgomaretseng.
• Ho thibela khanya ea morao-rao / boemo ba LED ho hang, u se ke ua hokahanya likhokahano tsa 7th tsa lihokelo tsa GPIO, kapa u behe boemo ba Output ba GPIO pin7 ho ea tlase ho sesebelisoa sa Lightware.

Ka morao View

Maemo a jumper

The Simplified Schematic of the Button Panel

Tšebeliso e Tloaelehileng (Example)

Example Tlhaloso
Phanele ea Likonopo e hokahane le boema-kepe ba GPIO ba matrix. Likonopo tse tšeletseng li na le mesebetsi e latelang:

Tataiso ea lithakhisa tsa P1-P6 GPIO ka har'a matrix li behiloe joalo ka Input. Ka hona, ha konopo e hatelloa boemo ba ho kenya pini bo fetoloa ho Low. Seo se sebelisoa e le Boemo bo hlahisang Ketso ho Motsamaisi oa Ketsahalo. Liketsahalo tse tšeletseng li hlalositsoe ho Motsamaisi oa Ketsahalo bakeng sa likonopo tse tšeletseng.

Konopo Panel Mounting

Phanele ea konopo ea TBP6-EU e ka beoa lebokoseng le ntseng le hola la lebota le tloaelehileng la Europe / le chitja:

Label le Cap Fixation
Li-caps tsa li-buttons li fanoa ka thoko le sehlahisoa ka mokotleng oa polasetiki. Khetha label eo u e batlang ebe u e kenya joalo ka ha ho bonts'itsoe setšoantšong se khomaretsoeng:

1. Kenya leibole.
2. Beha cap 'me u ele hloko linate; tataiso ea li-buttons e fapane, ka hona, li-caps tse itseng li tlameha ho potoloha ka 90 °.

Phoenix Connector Wiring

Mohala o khothaletsoang bakeng sa likhokahano ke AWG24 (diamore ea 0.2 mm2) kapa 'thapo ea alamo' e sebelisoang ka kakaretso e nang le lithapo tsa 8×0.22 mm2.

Mohala o pakeng tsa konopo ea konopo le boema-kepe ba GPIO o ile oa lekoa ke 50 m, mofuta oa cable oa AWG23. Bakeng sa sebaka se selelele, ka kopo ikopanye le Lightware.

* Malebela le maqheka ka Pin7
Pini ea 7th ea khokahano ea GPIO e ka sebelisoa bakeng sa efe kapa efe ea mesebetsi e latelang:

1. Konopo Backlight Mosebetsi
   Pini ea 7 ea konopo ea konopo e hokahane le pinana ea 7 ea boema-kepe ba GPIO sesebelisoa sa Lightware. Beha tataiso ea phini ea 7th pin ho ea Output le boemo ba Output ho ea Holimo mohlala ka ho sebelisa software ea LDC (Lightware Device Controller). Jumper e behiloe sebakeng sa JP1 kapa JP2. Ka hona, khanya ea morao ea likonopo e tsamaisoa holim'a pinana ea 7.
2. Maikutlo a Remote Boemo (Ketso ea Motsamaisi oa Ketsahalo)
   Pini ea 7 ea konopo ea konopo e hokahane le pinana ea 7 ea boema-kepe ba GPIO sesebelisoa sa Lightware. Jumper e behiloe ho JP3, tataiso ea pinana ea 7th pin e behiloe e le Output le Output level to Low. Ka hona, pinana ea 7 ea boema-kepe ba GPIO ka sesebelisoa sa Lightware e ka sebelisoa e le Ketso. Mohlala, ha projector e buletsoe, mabone a LED (boemo ba tlhahiso ea pin ea 7 bo fetoloa ho ea Holimo).
   • Karolo ena ha e fumanehe molemong oa MMX8x4-HT420M.
3. Tšebeliso e Tloaelehileng ea 7th Pin
   Tabeng ena li-LED tsa konopo ea konopo li tla ba lefifi. Pini ea 7 ea konopo ea konopo ha e kopane. Pini ea 7 ea boema-kepe ba GPIO sesebelisoa sa Lightware e tla ba mahala mme e ka sebelisoa e le ho kenya letsoho kapa tlhahiso.
   • Pini ea bo-7 ea boema-kepe ba GPIO ka har'a matrix ea MMX8x4-HT420M e romella 5V khafetsa.

Tlhaloso

Kakaretso

• Ho latela melao …………………………………………………………………………………………….CE, UKCA
• EMC (Emission)………………………………………………………………….EN 55032:2015+A1:2020
• EMC (Emission)……………………………………………………………..EN 55035:2017+A11:2020
• Ho latela polokeho…………………………………………………………………………… EN 62368-1:2020
• RoHS………………………………………………………………………………………………… EN 63000:2018
• Tiisetso…………………………………………………………………………………………………………..3 lilemo tse XNUMX.
• Mocheso oa ho sebetsa…………………………………………………….. 0 ho +50˚C (+32 ho +122˚F)
• Mongobo o sebetsang…………………………………………………………. 10% ho isa ho 90%, e sa fokotseng
• Ho phodisa …………………………………………………………………………………………………….. Passive
• Sebaka se koaletsoeng…………………………………………………………………………………………………. 1 mm tšepe
• Litekanyo……………………………………………………………………………. 80 W x 20 D x 80 H limilimithara
• Boima ba 'mele ………………………………………………………………………………………………………………….90 g

Matla

• Phepelo ea motlakase ………………………………………….. matla a hole ka phini ea 7 ea GPIO
  ………………………………………………………………………………………….. (feela bakeng sa tšebetso ea leseli)

GPIO

• Mofuta oa sehokelo………………………………………………………………………..8-pole Phoenix connector
• Palo ea lithakhisa tse ka lokisoang…………………………………………………………………………… ..7
• Tsela ea boema-kepe………………………………………………………………………………………………Kenyeletso kapa tlhahiso
• Keletso voltage: Tlase / Boemo bo phahameng…………………………………………………………….0 – 0,8V / 2 – 5V
• Sephetho voltage: Tlase / Boemo bo phahameng………………………………………………………. 0 - 0,5 V / 4.5 - 5 V

Litekanyo

Litekanyetso li ka mm.

Lisebelisoa tse lumellanang

Phanele ea konopo e ka hokahanngoa le sesebelisoa sa Lightware se kopantsoeng le boema-kepe ba 8-pole GPIO:

• UMX-TPS-TX130, UMX-TPS-TX140, UMX-TPS-TX140-Plus
• UMX-HDMI-140, UMX-HDMI-140-Plus
• DP-TPS-TX220
• HDMI-TPS-TX220
• SW4-OPT-TX240RAK
• DVI-HDCP-TPS-TX220
• SW4-TPS-TX240, SW4-TPS-TX240-Plus
• MMX8x4-HT420M

Leseli la Visual Engineering PLC.
Budapest, Hungary
sales@lightware.com
+36 1 255 3800
support@lightware.com
+36 1 255 3810

©2023 Lightware Visual Engineering. Litokelo tsohle li sirelelitsoe. Matšoao ohle a boletsoeng ke thepa ea beng ba ona. Litlhaloso li ka fetoha ntle le tsebiso.
Lintlha tse ling mabapi le sesebelisoa li fumaneha ho www.lightware.com.

Litokomane / Lisebelisoa

LIGHTWARE TBP6 Button Panel [pdf] Bukana ea Mosebelisi TBP6-EU-W, TBP6-EU-K, TBP6 Konopo Panel, TBP6, Konopo Panel, Phanele

Litšupiso

• Bukana ea Mosebelisi