Boardcon MINI507 Cost Optimized System Module
Selelekela
Mabapi le Bukana ena
Bukana ena e reretsoe ho fa mosebedisi ho fetaview ea boto le melemo, lintlha tse felletseng tsa likarolo, le ho theha lits'ebetso. E na le boitsebiso ba bohlokoa ba tšireletso hape.
Maikutlo le Nchafatso ea Bukana ena
Ho thusa bareki ba rona ho sebelisa lihlahisoa tsa rona hamolemo, re lula re etsa hore lisebelisoa tse ling tse nchafalitsoeng li fumanehe ho Boardcon websaete (www.boardcon.com , www.armdesigner.com). Tsena li kenyelletsa libuka, lintlha tsa kopo, mohlala oa lenaneoamples, le software e ntlafalitsoeng le hardware. Kena nako le nako ho bona tse ncha! Ha re beha mosebetsi pele ho lisebelisoa tsena tse nchafalitsoeng, maikutlo a tsoang ho bareki ke tšusumetso ea pele, Haeba u na le lipotso, maikutlo, kapa matšoenyeho ka sehlahisoa kapa morero oa hau, ka kopo u se ke ua tsilatsila ho ikopanya le rona ho support@armdesigner.com.
Tiisetso e Lekanyelitsoeng
Boardcon e fana ka tumello ea hore sehlahisoa sena se hloke bofokoli linthong tse bonahalang le moetsong nako ea selemo ho tloha ka letsatsi la theko. Nakong ena ea tiisetso Boardcon e tla lokisa kapa e nkele yuniti e nang le bothata ho latela mokhoa o latelang: Khopi ea invoice ea mantlha e tlameha ho kenyeletsoa ha e khutlisetsa unit e nang le bothata ho Boardcon. Tiisetso ena e lekanyelitsoeng ha e koahele litšenyehelo tse bakoang ke ho khantša kapa ho kenngoeng ha motlakase, tšebeliso e mpe, tšebeliso e mpe, maemo a sa tloaelehang a ts'ebetso, kapa liteko tsa ho fetola kapa ho fetola tšebetso ea sehlahisoa. Tiisetso ena e lekanyelitsoe ho lokisoeng kapa ho nkela sebaka se senyehileng. Ha ho ketsahalo e tla ba le boikarabello kapa boikarabello bakeng sa tahlehelo kapa ts'enyehelo efe kapa efe, ho kenyeletsoa empa e sa lekanyetsoe ho phaello efe kapa efe e lahlehileng, ts'enyehelo ea tšohanyetso kapa ea litlamorao, tahlehelo ea khoebo, kapa phaello e lebelletsoeng e bakoang ke ts'ebeliso kapa ho se khone ho sebelisa sehlahisoa sena. Litokiso li etsoa ka mor'a ho fela ha nako ea tiisetso li itšetlehile ka tefiso ea tokiso le litšenyehelo tsa ho khutlisa thepa. Ka kopo ikopanye le Boardcon ho hlophisa litšebeletso life kapa life tsa tokiso le ho fumana leseli la tefiso ea tokiso.
MINI507 Selelekela
Kakaretso
Sistimi ea MINI507-on-module e kentsoe ka Allwinner's T507 quad-core Cortex-A53, G31 MP2 GPU. E etselitsoe ka ho khetheha lisebelisoa tse bohlale tse kang molaoli oa indasteri, lisebelisoa tsa IoT, sehlopha sa dijithale le lisebelisoa tsa likoloi. Ts'ebetso e phahameng le tharollo ea matla a tlase e ka thusa bareki ho hlahisa theknoloji e ncha kapele le ho ntlafatsa katleho ea tharollo ka kakaretso. Ka ho khetheha, T507 e tšoaneleha ho etsa tlhahlobo ea AEC-Q100.
Likaroloana
- Microprocessor
- Quad-core Cortex-A53 ho fihla ho 1.5G
- 32KB I-cache, 32KB D-cache, 512KB L2 cache
- Memori Mokhatlo
- DDR4 RAM ho fihlela ho 4GB
- EMMC ho fihlela ho 64GB
- Qala ROM
- E ts'ehetsa ho jarolla khoutu ea sistimi ka USB OTG
- Tšireletso ID
- Boholo bo fihla ho 2Kbit bakeng sa ID ea ts'ireletso ea chip
- Setsi sa video / Encoder
- E tšehetsa li-decoding tsa video ho fihla ho 4K@30fps
- E tšehetsa H.264 encode
- H.264 HP e khouta ho fihla ho 4K@25fps
- Boholo ba setšoantšo bo fihla ho t0 4096×4096
- Hlahisa Subsystem
- Sephetho sa Video
- E tšehetsa transmitter ea HDMI 2.0 e nang le HDCP 1.4, ho fihla ho 4K@30fps (T507H kgetho)
- E tšehetsa segokanyimmediamentsi sa sebolokigolo sa RGB ho fihla ho 800×640@60fps
- E ts'ehetsa sebopeho sa LVDS Lihokelo tse peli ho fihla ho 1920 × 1080@60fps le sehokelo se le seng ho fihla ho 1366 × 768@60fps E tšehetsa RGB interface ho fihlela 1920 × 1080@60fps
- E tšehetsa BT656 segokanyimmediamentsi sa sebolokigolo ho fihla ho 1920×1080@30fps
- E ts'ehetsa tlhahiso ea 1ch TV ka ho bona plug
- Setšoantšo ka
- E tšehetsa tlhahiso ea MIPI CSI ho fihla ho 8M@30fps kapa 4x1080P@25fps
- E ts'ehetsa likhokahano tse bapileng ho fihla ho 1080P@30fps
- E tšehetsa BT656/BT1120
- Molaetsa oa analog
- E 'ngoe ea li-headphone tsa stereo
- I2S/PCM/ AC97
- Khokahano e meraro ea I2S/PCM
- Tšehetsa ho fihla ho 8-CH DMIC
- Kenyelletso le tlhahiso e le 'ngoe ea SPDIF
- USB
- Lisebelisoa tse 'nè tsa USB 2.0
- USB 2.0 OTG e le 'ngoe, le li-host tse tharo tsa USB
- Ethernet
- Ts'ehetsa li-interface tse peli tsa Ethernet
- E 'ngoe ea 10/100M PHY ho CPU Board
- Khokahano e le 'ngoe ea GMAC/EMAC
- I2C
- Ho fihlela ho li-I2C tse hlano
- Mokhoa o tloaelehileng oa ts'ehetso le mokhoa o potlakileng (ho fihla ho 400kbit / s)
- Sebadi sa Smart Card
- Ts'ehetsa lintlha tsa ISO/IEC 7816-3 le EMV2000(4.0).
- Ts'ehetsa li-synchronous le likarete life kapa life tseo e seng tsa ISO 7816 le tseo e seng tsa EMVcards
- SPI
- Balaoli ba babeli ba SPI, molaoli e mong le e mong oa SPI ea nang le matšoao a mabeli a CS
- Full-duplex synchronous serial interface
- 3 kapa 4-terata mode
- UART
- Ho fihla ho balaoli ba UART ba 6
- UART0/5 e nang le lithapo tse peli
- UART1/2/3/4 e 'ngoe le e 'ngoe e na le lithapo tse 4
- UART0 ea kamehla bakeng sa debug
- E lumellana le maemo a indasteri a 16550 UART
- Ts'ehetsa mokhoa oa RS485 ho lithapo tse 4 tsa UART
- CIR
- Balaoli ba CIR e le 'ngoe
- Flexible receiver bakeng sa moreki IR taolo e hole
- TSC
- Tšehetsa multiple lipalangoang molapo sebopeho
- Tšehetsa DVB-CSA V1.1/2.1 Descrambler
- ADC
- Kenyeletso e mene ea ADC
- Qeto ea 12-bit
- MoqtagE kenya letsoho pakeng tsa 0V le 1.8V
- KEYADC
- Mocha o le mong oa ADC bakeng sa ts'ebeliso ea bohlokoa
- Qeto ea 6-bit
- MoqtagE kenya letsoho pakeng tsa 0V le 1.8V
- Tšehetsa mokhoa o le mong, o tloaelehileng le o tsoelang pele
- PWM
- Li-PWM tse 6 (lipara tse 3 tsa PWM) tse nang le ts'ebetso ea tšitiso
- ho fihla ho 24/100MHz frequency ea tlhahiso
- Qeto e fokolang ke 1/65536
- Khaotsa Molaoli
- Ts'ehetsa likhatiso tse 28
- 3D Graphics Engine
- Phepelo ea ARM G31 MP2
- Tšehetsa OpenGL ES 3.2/2.0/1.1, Vulkan1.1, Open CL 2.0 standard
- Sehlopha sa matla
- AXP853T ka sekepeng
- Litšireletso tsa OVP/UVP/OTP/OCP
- DCDC6 0.5~3.4V@1A tlhahiso
- DCDC1 3.3V@300mA tlhahiso bakeng sa Carry board GPIO
- ALDO5 0.5~3.3V@300mA tlhahiso
- BLDO5 0.5~3.3V@500mA tlhahiso
- Ext-RTC IC ka sekepeng (khetho)
- RTC e tlase haholo e sebelisa hona joale, e ka tlase ho 5uA ho 3V konopo ea Cell (khetho)
- Mocheso
- Boemo ba indasteri, mocheso oa ho sebetsa: -40 ~ 85°C
Setšoantšo se Thibeloang
Setšoantšo sa T507 Block
Boto ea nts'etsopele (EMT507) Block Diagram
Litlhaloso tsa Mini507
| Sebopeho | Litlhaloso |
| CPU | Quad-core Cortex-A53 |
| DDR | 2GB DDR4 (ho fihla ho 4GB) |
| eMMC LEHLANYA | 8GB (ho fihla ho 64GB) |
| Matla | DC 5V |
| LVDS | Dual CH ho fihla ho 4-Lane |
| I2S | EA-3-CH |
| MIPI_CSI | EA-1-CH |
| TSC | EA-1-CH |
| HDMI tsoa | 1-CH(khetho) |
| Khamera | 1-CH(DVP) |
| USB | 3-CH (USB HOST2.0), 1-CH(OTG 2.0) |
|
Ethernet |
1000M GMAC
Le 100M PHY |
| SDMMC | EA-2-CH |
| SPDIF RX/TX | EA-1-CH |
| I2C | EA-5-CH |
| SPI | EA-2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| PWM | EA-6-CH |
| ADC IN | EA-4-CH |
| Boto Dimension | 51 x 65 limilimithara |
Boemo ba Mini507 PCB
MINI507 Pin Definition
| J1 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 1 | MDI-RN | 100M PHY MDI | 1.8V | |
| 2 | MDI-TN | 100M PHY MDI | 1.8V | |
| 3 | MDI-RP | 100M PHY MDI | 1.8V | |
| 4 | MDI-TP | 100M PHY MDI | 1.8V | |
| 5 | LED0/PHYAD0 | 100M PHY Link LED- | 3.3V | |
| 6 | LED3/PHYAD3 | 100M PHY Lebelo la LED+ | 3.3V | |
| 7 | GND | Fatše | 0V |
| J1 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 8 | GND | Fatše | 0V | |
|
9 |
LVDS0-CLKN/LCD-
D7 |
LVDS kapa RGB e bonts'a sebopeho |
PD7/EINT7/TS0-D3 |
3.3V |
|
10 |
Tlhaloso: LVDS0-D3N/LCD-D
9 |
LVDS kapa RGB e bonts'a sebopeho |
PD9/EINT9/TS0-D5 |
3.3V |
|
11 |
LVDS0-CLKP/LCD-
D6 |
LVDS kapa RGB e bonts'a sebopeho |
PD6/EINT6/TS0-D2 |
3.3V |
|
12 |
Tlhaloso: LVDS0-D3P/LCD-D
8 |
LVDS kapa RGB e bonts'a sebopeho |
PD8/EINT8/TS0-D4 |
3.3V |
|
13 |
Tlhaloso: LVDS0-D2P/LCD-D
4 |
LVDS kapa RGB e bonts'a sebopeho |
PD4/EINT4/TS0-D0 |
3.3V |
|
14 |
Tlhaloso: LVDS0-D1N/LCD-D
3 |
LVDS kapa RGB e bonts'a sebopeho |
PD3/EINT3/TS0-DVL
D |
3.3V |
|
15 |
Tlhaloso: LVDS0-D2N/LCD-D
5 |
LVDS kapa RGB e bonts'a sebopeho |
PD5/EINT5/TS0-D1 |
3.3V |
|
16 |
Tlhaloso: LVDS0-D1P/LCD-D
2 |
LVDS kapa RGB e bonts'a sebopeho |
PD2/EINT2/TS0-SYN
C |
3.3V |
|
17 |
Tlhaloso: LVDS1-D3N/LCD-D
19 |
LVDS kapa RGB e bonts'a sebopeho |
PD19/EINT19 |
3.3V |
|
18 |
Tlhaloso: LVDS0-D0N/LCD-D
1 |
LVDS kapa RGB e bonts'a sebopeho |
PD1/EINT1/TS0-EER |
3.3V |
|
19 |
Tlhaloso: LVDS1-D3P/LCD-D
18 |
LVDS kapa RGB e bonts'a sebopeho |
PD18/EINT18/SIM0-
DET |
3.3V |
|
20 |
Tlhaloso: LVDS0-D0P/LCD-D
0 |
LVDS kapa RGB e bonts'a sebopeho |
PD0/EINT0/TS0-CLK |
3.3V |
|
21 |
Tlhaloso: LVDS1-D2N/LCD-D
15 |
LVDS kapa RGB e bonts'a sebopeho |
PD15/EINT15/SIM0-
CLK |
3.3V |
|
22 |
LVDS1-CLKN/LCD-
D17 |
LVDS kapa RGB e bonts'a sebopeho |
PD17/EINT17/SIM0-
RST |
3.3V |
|
23 |
Tlhaloso: LVDS1-D2P/LCD-D
14 |
LVDS kapa RGB e bonts'a sebopeho |
PD14/EINT14/SIM0-
PWREN |
3.3V |
|
24 |
LVDS1-CLKP/LCD-
D16 |
LVDS kapa RGB e bonts'a sebopeho |
PD16/EINT16/SIM0-
DATA |
3.3V |
|
25 |
Tlhaloso: LVDS1-D1N/LCD-D
13 |
LVDS kapa RGB e bonts'a sebopeho |
PD13/EINT13/SIM0-
VPPPP |
3.3V |
|
26 |
Tlhaloso: LVDS1-D0N/LCD-D
11 |
LVDS kapa RGB e bonts'a sebopeho |
PD11/EINT11/TS0-D
7 |
3.3V |
|
27 |
Tlhaloso: LVDS1-D1P/LCD-D
12 |
LVDS kapa RGB e bonts'a sebopeho |
PD12/EINT12/SIM0-
VPPEN |
3.3V |
|
28 |
Tlhaloso: LVDS1-D0P/LCD-D
10 |
LVDS kapa RGB e bonts'a sebopeho |
PD10/EINT10/TS0-D
6 |
3.3V |
| 29 | LCD-D20 | RGB e bonts'a sebopeho | PD20/EINT20 | 3.3V |
| J1 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 30 | LCD-D22 | RGB e bonts'a sebopeho | PD22/EINT22 | 3.3V |
| 31 | LCD-D21 | RGB e bonts'a sebopeho | PD21/EINT21 | 3.3V |
| 32 | LCD-D23 | RGB e bonts'a sebopeho | PD23/EINT23 | 3.3V |
| 33 | LCD-PWM | PWM0 | PD28/EINT28 | 3.3V |
| 34 | LCD-HSYNC | RGB e bonts'a sebopeho | PD26/EINT26 | 3.3V |
| 35 | GND | Fatše | 0V | |
| 36 | LCD-VSYNC | RGB e bonts'a sebopeho | PD27/EINT27 | 3.3V |
| 37 | LCD-CLK | RGB e bonts'a sebopeho | PD24/EINT24 | 3.3V |
| 38 | LCD-DE | RGB e bonts'a sebopeho | PD25/EINT25 | 3.3V |
| 39 | GND | Fatše | 0V | |
| 40 | GND | Fatše | 0V | |
| 41 | USB3-DM | USB3 data - | 3.3V | |
| 42 | HTX2N | HDMI e hlahisoang ke data2- | 1.8V | |
| 43 | USB3-DP | USB3 data + | 3.3V | |
| 44 | HTX2P | HDMI e hlahisoang ke data2+ | 1.8V | |
| 45 | USB2-DM | USB2 data - | 3.3V | |
| 46 | HTX1N | HDMI e hlahisoang ke data1- | 1.8V | |
| 47 | USB2-DP | USB2 data + | 3.3V | |
| 48 | HTX1P | HDMI e hlahisoang ke data1+ | 1.8V | |
| 49 | USB1-DM | USB1 data - | 3.3V | |
| 50 | HTX0N | HDMI e hlahisoang ke data0- | 1.8V | |
| 51 | USB1-DP | USB1 data + | 3.3V | |
| 52 | HTX0P | HDMI e hlahisoang ke data0+ | 1.8V | |
| 53 | USB0-DM | USB0 data - | 3.3V | |
| 54 | HTXCN | HDMI Clock - | 1.8V | |
| 55 | USB0-DP | USB0 data + | 3.3V | |
| 56 | HTXCP | HDMI Oache + | 1.8V | |
| 57 | GND | Fatše | 0V | |
| 58 | HSDA | Lintlha tsa serial tsa HDMI | U hloka ho hula 5V | 5V |
| 59 | UART0-TX | Tlosa Uart | PH0/EINT0/PWM3 | 3.3V |
| 60 | HSCL | HDMI serial ea CLK | U hloka ho hula 5V | 5V |
| 61 | UART0-RX | Tlosa Uart | PH1/EINT1/PWM4 | 3.3V |
| 62 | HHPD | Ho lemoha ha HDMI hot plug | 5V | |
| 63 | PH4 | GPIO kapa SPDIF tlhahiso | I2C3_SCL/PH-EINT4 | 3.3V |
|
64 |
HCEC |
Lisebelisoa tsa elektroniki tsa HDMI
taolo |
3.3V |
|
| 65 | GND | Fatše | 0V | |
| 66 | GND | Fatše | 0V | |
| 67 | MCSI-D3N | Lintlha tse fapaneng tsa MIPI CSI 3N | 1.8V | |
| 68 | MCSI-D2N | Lintlha tse fapaneng tsa MIPI CSI 2N | 1.8V | |
| 69 | MCSI-D3P | MIPI CSI data e fapaneng 3P | 1.8V | |
| 70 | MCSI-D2P | MIPI CSI data e fapaneng 2P | 1.8V |
| J1 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 71 | MCSI-CLKN | MIPI CSI oache e fapaneng ea N | 1.8V | |
| 72 | MCSI-D1N | Lintlha tse fapaneng tsa MIPI CSI 1N | 1.8V | |
| 73 | MCSI-CLKP | MIPI CSI oache e fapaneng P | 1.8V | |
| 74 | MCSI-D1P | MIPI CSI data e fapaneng 1P | 1.8V | |
| 75 | GND | Fatše | 0V | |
| 76 | MCSI-D0N | Lintlha tse fapaneng tsa MIPI CSI 0N | 1.8V | |
| 77 | UART5-RX | UART5 kapa SPDIF ho kapa I2C2SDA | PH3/EINT3/PWM1 | 3.3V |
| 78 | MCSI-D0P | MIPI CSI data e fapaneng 0P | 1.8V | |
|
79 |
UART5-TX |
UART5 kapa SPDIF CLK kapa
I2C2SCL |
PH2/EINT2/PWM2 |
3.3V |
| 80 | PH-I2S3-DOUT0 | I2S-D0 kapa DIN1/SPI1-MISO | PH8/EINT8/CTS2 | 3.3V |
| 81 | LINEOUTR | Tlhahiso ea mohala oa Analog R | Hloka Coupling CAP | 1.8V |
| 82 | PH-I2S3-MCLK | I2S-CLK/SPI1-CS0/UART2-TX | PH5/EINT5/I2C3SDA | 3.3V |
| 83 | LINEOUTL | Tlhahiso ea mohala oa Analog L | Hloka Coupling CAP | 1.8V |
| 84 | PH-I2S3-DIN0 | I2S-D1 or DIN0/SPI1-CS1 | PH9/EINT9 | 3.3V |
| 85 | TS'OANANG | Setsi sa Audio | 0V | |
| 86 | PH-I2S3-LRLK | I2S-CLK/SPI1MOSI/UART2RTS | PH7/EINT7/I2C4SDA | 3.3V |
| 87 | PC3 | Boot-SEL1/SPI0-CS0 | PC-EINT3 | 1.8V |
| 88 | PH-I2S3-BCLK | I2S-CLK/SPI1-CLK/UART2-RX | PH6/EINT6/I2C4SCL | 3.3V |
| 89 | PC4 | Boot-SEL2/SPI0-MISO | PC-EINT4 | 1.8V |
| 90 | LRADC | Kenyelletso ea senotlolo sa 6bit ADC | 1.8V | |
| 91 | GPADC3 | Kakaretso ea 12bit ADC3 ka | 1.8V | |
| 92 | GPADC1 | Kakaretso ea 12bit ADC1 ka | 1.8V | |
| 93 | GPADC0 | Kakaretso ea 12bit ADC0 ka | 1.8V | |
| 94 | GPADC2 | Kakaretso ea 12bit ADC2 ka | 1.8V | |
| 95 | TV-TSOANG | Tlhahiso ea CVBS | 1.0V | |
| 96 | PA/TWI3-SDA | PA11/EINT11 | 3.3V | |
| 97 | IR-RX | Keletso ea IR | PH10/EINT10 | 3.3V |
| 98 | PA/TWI3-SCK | PA10/EINT10 | 3.3V | |
| 99 | PC7 | SPI0-CS1 | PC-EINT7 | 1.8V |
| 100 | GND | Fatše | 0V | |
| J2 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 1 | PE13 | CSI0-D9 | PE13/EINT14 | 3.3V |
| 2 | GND | Fatše | 0V | |
| 3 | PE14 | CSI0-D10 | PE14/EINT15 | 3.3V |
| 4 | SPI0_CLK_1V8 | PC0/EINT0 | 1.8V | |
| 5 | PE15 | CSI0-D11 | PE-EINT16 | 3.3V |
| 6 | PE12 | CSI0-D8 | PE-EINT13 | 3.3V |
| 7 | PE0 | Setšoantšo sa CSI0-PCLK | PE-EINT1 | 3.3V |
| 8 | PE18 | CSI0-D14 | PE-EINT19 | 3.3V |
| 9 | PE16 | CSI0-D12 | PE-EINT17 | 3.3V |
| 10 | PE19 | CSI0-D15 | PE-EINT20 | 3.3V |
| J2 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 11 | PE17 | CSI0-D13 | PE-EINT18 | 3.3V |
| 12 | PE8 | CSI0-D4 | PE-EINT9 | 3.3V |
| 13 | SDC0-DET | Ho fumana karete ea SD | PF6/EINT6 | 3.3V |
| 14 | PE3 | CSI0-VSYNC | PE-EINT4 | 3.3V |
| 15 | GND | Fatše | 0V | |
| 16 | PE2 | CSI0-HSYNC | PE-EINT3 | 3.3V |
| 17 | SDC0-D0 | Lethathamo la lintlha tsa SD0 | PF1/EINT1 | 3.3V |
| 18 | PE1 | CSI0-MCLK | PE-EINT2 | 3.3V |
| 19 | SDC0-D1 | Lethathamo la lintlha tsa SD1 | PF0/EINT0 | 3.3V |
| 20 | SPI0_MOSI_1V8 | PC2/EINT2 | 1.8V | |
| 21 | SDC0-D2 | Lethathamo la lintlha tsa SD2 | PF5/EINT5 | 0V |
| 22 | PE4 | CSI0-D0 | PE-EINT5 | 3.3V |
| 23 | SDC0-D3 | Lethathamo la lintlha tsa SD3 | PF4/EINT4/ | 3.3V |
| 24 | PE5 | CSI0-D1 | PE-EINT6 | 3.3V |
| 25 | SDC0-CMD | Letšoao la Taelo la SD | PF3/EINT3 | 3.3V |
| 26 | PE7 | CSI0-D3 | PE-EINT8 | 3.3V |
| 27 | SDC0-CLK | Tlhahiso ea Clock ea SD | PF2/EINT2 | 3.3V |
| 28 | PE6 | CSI0-D2 | PE-EINT7 | 3.3V |
| 29 | GND | Fatše | 0V | |
| 30 | PE9 | CSI0-D5 | PE-EINT10 | 3.3V |
| 31 | EPHY-CLK-25M | UART4CTS/CLK-Fanout1 | PI16/EINT16/TS0-D7 | 3.3V |
| 32 | PE10 | CSI0-D6 | PE-EINT11 | 3.3V |
| 33 | RGMII-MDIO | UART4RTS/CLK-Fanout0 | PI15/EINT15/TS0-D6 | 3.3V |
| 34 | PE11 | CSI0-D7 | PE-EINT12 | 3.3V |
| 35 | RGMII-MDC | UART4-RX/PWM4 | PI14/EINT14/TS0-D5 | 3.3V |
| 36 | CK32KO | I2S2-MCLK/AC-MCLK | PG10/EINT10 | 1.8V |
| 37 | RGMII-RXCK | H-I2S0-DIN0/DO1 | PI4/EINT4/DMIC-D3 | 3.3V |
| 38 | GND | Fatše | 0V | |
| 39 | RGMII-RXD3 | H-I2S0-MCLK | PI0/EINT0/DMICLK | 3.3V |
| 40 | PG-MCSI-SCK | I2C3-SCL/UART2-RTS | PG17/EINT17 | 1.8V |
| 41 | RGMII-RXD2 | H-I2S0-BCLK | PI1/EINT1/DMIC-D0 | 3.3V |
| 42 | PG-MCSI-SDA | I2C3-SDA/UART2-CTS | PG18/EINT18 | 1.8V |
| 43 | RGMII-RXD1 | RMII-RXD1/H-I2S0-LRCK | PI2/EINT2/DMIC-D1 | 3.3V |
| 44 | PE-TWI2-SCK | CSI0-SCK | PE20-EINT21 | 3.3V |
| 45 | RGMII-RXD0 | RMII-RXD0/H-I2S0-DO0/DIN1 | PI1/EINT1/DMIC-D2 | 3.3V |
| 46 | PE-TWI2-SDA | CSI0-SDA | PE21-EINT22 | 3.3V |
| 47 | RGMII-RXCTL | RMII-CRS/UART2TX/I2C0SCL | PI5/EINT5/TS0-CLK | 3.3V |
| 48 | BT-PCM-CLK | H-I2S2-BCLK/AC-SYNC | PG11/EINT11 | 1.8V |
| 49 | GND | Fatše | 0V | |
| 50 | BT-PCM-SYNC | H-I2S2-LRCLK/AC-ADCL | PG12/EINT12 | 1.8V |
| 51 | RGMII-TXCK | RMII-TXCK/UART3RTS/PWM1 | PI11/EINT11/TS0-D2 | 3.3V |
| 52 | BT-PCM-DOUT | H-I2S2-DO0/DIN1/AC-ADCR | PG13/EINT13 | 1.8V |
| J2 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 53 | RGMII-TXCTL | RMII-TXEN/UART3CTS/PWM2 | PI12/EINT12/TS0-D3 | 3.3V |
| 54 | BT-PCM-DIN | H-I2S2-DO1/DIN0/AC-ADCX | PG14/EINT14 | 1.8V |
| 55 | RGMII-TXD3 | UART2-RTS/I2C1-SCL | PI7/EINT7/TS0SYNC | 3.3V |
| 56 | BT-UART-RTS | UART1-RTS/PLL-LOCK-DBG | PG8/EINT8 | 1.8V |
| 57 | RGMII-TXD2 | UART2-CTS/I2C1-SDA | PI8/EINT8/TS0DVLD | 3.3V |
| 58 | BT-UART-CTS | UART1-CTS/AC-ADCY | PG9/EINT9 | 1.8V |
| 59 | RGMII-TXD1 | RMII-TXD1/UART3TX/I2C2SCL | PI9/EINT9/TS0-D0 | 3.3V |
| 60 | BT-UART-RX | UART1-RX | PG7/EINT7 | 1.8V |
| 61 | RGMII-TXD0 | RMII-TXD0/UART3RX/I2C2SDA | PI10/EINT10/TS0-D1 | 3.3V |
| 62 | BT-UART-TX | UART1-TX | PG6/EINT6 | 1.8V |
| 63 | GND | Fatše | 0V | |
| 64 | GND | Fatše | 0V | |
| 65 | RGMII-CLKIN-125M | UART4-TX/PWM3 | PI13/EINT13/TS0-D4 | 3.3V |
| 66 | WL-SDIO-D0 | SDC1-D0 | PG2/EINT2 | 1.8V |
|
67 |
PHYRSTB |
RMII-RXER/UART2-RX/I2C0-S
DA |
PI6/EINT6/TS0-EER |
3.3V |
| 68 | WL-SDIO-D1 | SDC1-D1 | PG3/EINT3 | 1.8V |
| 69 | GND | Fatše | 0V | |
| 70 | WL-SDIO-D2 | SDC1-D2 | PG4/EINT4 | 1.8V |
| 71 | MCSI-MCLK | PWM1 | PG19/EINT19 | 1.8V |
| 72 | WL-SDIO-D3 | SDC1-D3 | PG5/EINT5 | 1.8V |
| 73 | GND | Fatše | 0V | |
| 74 | WL-SDIO-CMD | SDC1-CMD | PG1/EINT1 | 1.8V |
| 75 | PG-TWI4-SCK | I2C4-SCL/UART2-TX | PG15/EINT15 | 1.8V |
| 76 | WL-SDIO-CLK | SDC1-CLK | PG0/EINT0 | 1.8V |
| 77 | PG-TWI4-SDA | I2C4-SDA/UART2-RX | PG16/EINT16 | 1.8V |
| 78 | GND | Fatše | 0V | |
|
79 |
FEL |
Khetha mokhoa oa ho qala:
Tlase: khoasolla ho tsoa ho USB, Holimo: boot e potlakileng |
3.3V |
|
| 80 | ALDO5 | PMU ALDO5 tlhahiso ea kamehla ea 1.8V | Boholo:300mA | 1.8V |
| 81 | EXT-IRQ | Kenyelletso ea kantle ea IRQ | OD | |
| 82 | BLDO5 | PMU ALDO5 tlhahiso ea kamehla ea 1.2V | Boholo:500mA | 1.2V |
| 83 | PMU-PWRON | Hokela ho Senotlolo sa Matla | 1.8V | |
| 84 | GND | Fatše | 0V | |
| 85 | RTC-BAT | Ho kenya betri ea RTC | 1.8-3.3V | |
| 86 | VSYS_3V3 | Phallo ea sistimi ea 3.3V | Boholo: 300mA | 3.3V |
| 87 | GND | Fatše | 0V | |
| 88 | DCDC6 | PMU DCDC6 kantle(3V3 ea kamehla) | Boholo: 1000mA | 3.3V |
| 89 | SOC-RESET | Sephetho sa Reset ea Sisteme | Hokela ho konopo ea RST | 1.8V |
| 90 | DCDC6 | PMU DCDC6 kantle(3V3 ea kamehla) | Boholo: 1000mA | 3.3V |
| 91 | GND | Fatše | 0V |
| J2 | Letshwao | Tlhaloso | Mesebetsi e meng | Moqtage |
| 92 | GND | Fatše | 0V | |
| 93 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| 94 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| 95 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| 96 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| 97 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| 98 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| 99 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| 100 | DCIN | Kenyelletso ea Matla a Maholo | 3.4V-5.5V | |
| Hlokomela
1. J1 Pin87/89(PC3/PC4) e amahanngoa le Boot-SEL, ka kopo o seke oa hula H kapa L. 2. Yuniti ea PC/PG e maemong a kamehla a 1.8V, empa e ka fetohela ho 3.3V. |
||||
Development Kit (EMT507)
Tataiso ea Moralo oa Hardware
Peripheral Circuit Reference
Matla a Kantle
Debug Circuit
USB OTG Interface Circuit
HDMI Interface Circuit
Sefate sa Matla
B2B sehokelo bakeng sa boto ea mojari
Litšobotsi tsa Motlakase oa Sehlahisoa
Ho senya le Mocheso
| Letšoao | Paramethara | Min | Tlanya | Max | Yuniti |
|
DCIN |
Sesebelisoa sa Voltage |
3.4 |
5 |
5.5 |
V |
|
VSYS_3V3 |
Sistimi ea IO
Moqtage |
3.3-5% |
3.3 |
3.3 + 5% |
V |
|
DCDC6_3V3 |
Peripheral
Moqtage |
3.3-5% |
3.3 |
3.3 + 5% |
V |
|
ALDO5 |
Khamera IO
Moqtage |
0.5 |
1.8 |
3.3 |
V |
|
BLDO5 |
Core ea khamera
Moqtage |
0.5 |
1.2 |
3.3 |
V |
|
Idcin |
DCIN
input Current |
500 |
mA |
||
|
VCC_RTC |
Phatlalatso ea RTCtage |
1.8 |
3 |
3.4 |
V |
|
Irtc |
Tlhahiso ea RTC
Hona joale |
TDB |
uA |
||
|
Ta |
Ho sebetsa
Mocheso |
-40 |
85 |
°C |
|
|
Tstg |
Mocheso oa polokelo |
-40 |
120 |
°C |
Botšepehi ba Teko
| Teko ea Ts'ebetso ea Mocheso o Phahameng | ||
| Litaba | E sebetsa 8h ka mocheso o phahameng | 55 ° C ± 2 ° C |
| Sephetho | TDB | |
| Teko ea Bophelo ea Ts'ebetso | ||
| Litaba | Ho sebetsa ka kamoreng | 120h |
| Sephetho | TDB | |
Litokomane / Lisebelisoa
 |
Boardcon MINI507 Cost Optimized System Module [pdf] Bukana ea Mosebelisi T507, V1.202308, MINI507, MINI507 Cost Optimized System Module, Cost Optimized System Module, Optimized System Module, System Module, Module |
